intel 82576 (quad-port gigabit)

[jym <jym%eileo.net@localhost>]

Hello,

I've a strange behavior on Intel quad port ethernet card. Only two port (wm0 
and wm2) have good ethernet addresses. Others (wm1 and wm3) show 
"ff:ff:ff:ff:ff:ff".

This is a NetBSD-current from today (82576  only supported in current). 

Does anybody is using the same card ?


Thanks!
jym



dmesg is:

wm0 at pci3 dev 0 function 0: 82576 quad-1000BaseT Ethernet, rev. 1
wm0: interrupting at ioapic0 pin 18
wm0: PCI-Express bus
wm0: 65536 word (16 address bits) SPI EEPROM
wm0: Ethernet address 00:1b:21:6e:e6:30
igphy0 at wm0 phy 1: i82566 10/100/1000 media interface, rev. 1
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
wm1 at pci3 dev 0 function 1: 82576 quad-1000BaseT Ethernet, rev. 1
wm1: interrupting at ioapic0 pin 19
wm1: PCI-Express bus
wm1: 65536 word (16 address bits) SPI EEPROM
wm1: Ethernet address ff:ff:ff:ff:ff:ff
igphy1 at wm1 phy 1: i82566 10/100/1000 media interface, rev. 1
igphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
wm2 at pci4 dev 0 function 0: 82576 quad-1000BaseT Ethernet, rev. 1
wm2: interrupting at ioapic0 pin 16
wm2: PCI-Express bus
wm2: 65536 word (16 address bits) SPI EEPROM
wm2: Ethernet address 00:1b:21:6e:e6:34
igphy2 at wm2 phy 1: i82566 10/100/1000 media interface, rev. 1
igphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
wm3 at pci4 dev 0 function 1: 82576 quad-1000BaseT Ethernet, rev. 1
wm3: interrupting at ioapic0 pin 17
wm3: PCI-Express bus
wm3: 65536 word (16 address bits) SPI EEPROM
wm3: Ethernet address ff:ff:ff:ff:ff:ff
igphy3 at wm3 phy 1: i82566 10/100/1000 media interface, rev. 1
igphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto


ifconfig show same things:

wm0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        
capabilities=7ff80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx,TCP6CSUM_Rx,TCP6CSUM_Tx,UDP6CSUM_Rx,UDP6CSUM_Tx,TSO6>
        enabled=0
        address: 00:1b:21:6e:e6:30
        media: Ethernet autoselect (1000baseT full-duplex)
        status: active
        inet6 fe80::21b:21ff:fe6e:e630%wm0 prefixlen 64 scopeid 0x1
wm1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        
capabilities=7ff80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx,TCP6CSUM_Rx,TCP6CSUM_Tx,UDP6CSUM_Rx,UDP6CSUM_Tx,TSO6>
        enabled=0
        address: ff:ff:ff:ff:ff:ff
        media: Ethernet autoselect (1000baseT full-duplex,master)
        status: active
wm2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        
capabilities=7ff80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx,TCP6CSUM_Rx,TCP6CSUM_Tx,UDP6CSUM_Rx,UDP6CSUM_Tx,TSO6>
        enabled=0
        address: 00:1b:21:6e:e6:34
        media: Ethernet autoselect (1000baseT full-duplex)
        status: active
wm3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        
capabilities=7ff80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx,TCP6CSUM_Rx,TCP6CSUM_Tx,UDP6CSUM_Rx,UDP6CSUM_Tx,TSO6>
        enabled=0
        address: ff:ff:ff:ff:ff:ff
        media: Ethernet autoselect (1000baseT full-duplex)
        status: active
bnx0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        
capabilities=3f00<IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx,UDP4CSUM_Rx,UDP4CSUM_Tx>
        enabled=0
        address: b8:ac:6f:8e:b4:b0
        media: Ethernet autoselect (1000baseT full-duplex,master)
        status: active