Current-Users archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

acpi does not work in my hp6515b laptop



Hi,
I installed the i386 5.0 release,  I can not boot the system with acpi enable,
the system is hang up at "uhub5 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1".
attached file is the dmesg output.

Thanks.

Zhongjie Zhu
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0 (GENERIC) #0: Sun Apr 26 18:50:08 UTC 2009
        
builds%b6.netbsd.org@localhost:/home/builds/ab/netbsd-5-0-RELEASE/i386/200904260229Z-obj/home/builds/ab/netbsd-5-0-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 1919 MB
avail memory = 1874 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Hewlett-Packard HP Compaq 6515b (FJ174PA#AB2) (F.0E)
mainbus0 (root)
cpu0 at mainbus0: AMD 686-class, 1995MHz, id 0x60f82
cpu0: AMD PowerNow! Technology 2000 MHz
cpu0: available frequencies (Mhz): 800 1600 1800 2000
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1002 product 0x7910 (rev. 0x00)
ppb0 at pci0 dev 1 function 0: vendor 0x1002 product 0x7912 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 5 function 0: vendor 0x1002 product 0x791f (rev. 0x00)
vga1: WARNING: ignoring 64-bit BAR @ 0x10
vga1: WARNING: ignoring 64-bit BAR @ 0x18
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
ppb1 at pci0 dev 4 function 0: vendor 0x1002 product 0x7914 (rev. 0x00)
pci2 at ppb1 bus 16
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci2 dev 0 function 0: Broadcom BCM5787M Gigabit Ethernet
bge0: interrupting at irq 10
bge0: ASIC BCM5754/5787 A2 (0xb002), Ethernet address 00:1f:29:91:57:b4
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5754/5787 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb2 at pci0 dev 5 function 0: vendor 0x1002 product 0x7915 (rev. 0x00)
pci3 at ppb2 bus 32
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 6 function 0: vendor 0x1002 product 0x7916 (rev. 0x00)
pci4 at ppb3 bus 48
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x14e4 product 0x4311 (miscellaneous network, revision 0x02) at pci4 dev 
0 function 0 not configured
ixpide0 at pci0 dev 18 function 0
ixpide0: ATI Technologies IXP IDE Controller (rev. 0x00)
ixpide0: bus-master DMA support present
ixpide0: primary channel configured to native-PCI mode
ixpide0: using irq 10 for native-PCI interrupt
atabus0 at ixpide0 channel 0
ixpide0: secondary channel configured to native-PCI mode
atabus1 at ixpide0 channel 1
ohci0 at pci0 dev 19 function 0: vendor 0x1002 product 0x4387 (rev. 0x00)
ohci0: interrupting at irq 11
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 19 function 1: vendor 0x1002 product 0x4388 (rev. 0x00)
ohci1: interrupting at irq 5
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ohci2 at pci0 dev 19 function 2: vendor 0x1002 product 0x4389 (rev. 0x00)
ohci2: interrupting at irq 5
ohci2: OHCI version 1.0, legacy support
usb2 at ohci2: USB revision 1.0
ohci3 at pci0 dev 19 function 3: vendor 0x1002 product 0x438a (rev. 0x00)
ohci3: interrupting at irq 5
ohci3: OHCI version 1.0, legacy support
usb3 at ohci3: USB revision 1.0
ohci4 at pci0 dev 19 function 4: vendor 0x1002 product 0x438b (rev. 0x00)
ohci4: interrupting at irq 5
ohci4: OHCI version 1.0, legacy support
usb4 at ohci4: USB revision 1.0
ehci0 at pci0 dev 19 function 5: vendor 0x1002 product 0x4386 (rev. 0x00)
ehci0: interrupting at irq 11
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: ohci0 ohci1 ohci2 ohci3 ohci4
usb5 at ehci0: USB revision 2.0
piixpm0 at pci0 dev 20 function 0
piixpm0: vendor 0x1002 product 0x4385 (rev. 0x14)
piixpm0: interrupting at SMIpiixpm0: polling
iic0 at piixpm0: I2C bus
ixpide1 at pci0 dev 20 function 1
ixpide1: ATI Technologies IXP IDE Controller (rev. 0x00)
ixpide1: bus-master DMA support present
ixpide1: primary channel configured to compatibility mode
ixpide1: primary channel interrupting at irq 14
atabus2 at ixpide1 channel 0
ixpide1: secondary channel wired to compatibility mode
ixpide1: secondary channel interrupting at irq 15
atabus3 at ixpide1 channel 1
azalia0 at pci0 dev 20 function 2: Generic High Definition Audio Controller
azalia0: interrupting at irq 10
azalia0: host: 0x1002/0x4383 (rev. 0), HDA rev. 1.0
pcib0 at pci0 dev 20 function 3
pcib0: vendor 0x1002 product 0x438d (rev. 0x00)
ppb4 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x00)
pci5 at ppb4 bus 2
pci5: i/o space, memory space enabled
cbb0 at pci5 dev 4 function 0: vendor 0x1180 product 0x0476 (rev. 0xb6)
fwohci0 at pci5 dev 4 function 1: vendor 0x1180 product 0x0832 (rev. 0x02)
fwohci0: interrupting at irq 5
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:02:3f:99:29:51:2c:10
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
cbb0: cacheline 0x0 lattimer 0x40
cbb0: bhlc 0x824000
cbb0: interrupting at irq 10
cardslot0 at cbb0
cardbus0 at cardslot0: bus 3
pcmcia0 at cardslot0
pchb1 at pci0 dev 24 function 0
pchb1: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb2 at pci0 dev 24 function 1
pchb2: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb3 at pci0 dev 24 function 2
pchb3: vendor 0x1022 product 0x1102 (rev. 0x00)
amdtemp0 at pci0 dev 24 function 3
amdtemp0: AMD CPU Temperature Sensors (K8: core rev BH-G2, socket S1)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pms0: Synaptics touchpad version 6.2
pms0: Palm detect, Multi-finger
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
attimer0: attached to pcppi0
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: Analog Devices AD1981HD (rev. 2.0), HDA rev. 1.0
azalia0: codec[1]: 0x11c1/0x1040 (rev. 2.0), HDA rev. 1.0
azalia0: codec[1]: No support for modem function groups
azalia0: codec[1] has no audio function groups
audio0 at azalia0: full duplex, independent
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 10 ports with 10 removable, self powered
wd0 at atabus0 drive 0: <TOSHIBA MK1646GSX>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(ixpide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus2: 2 targets
cd0 at atapibus0 drive 0: <MATSHITADVD-RAM UJ-861H, HE58  537537, 1.50> cdrom 
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(ixpide1:0:0): using PIO mode 4, DMA mode 2 (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
umass0 at uhub5 port 1 configuration 1 interface 0
umass0: Kingston DataTraveler 2.0, rev 2.00/1.10, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <Kingston, DataTraveler 2.0, PMAP> disk 
removable
sd0: 1919 MB, 7676 cyl, 16 head, 32 sec, 512 bytes/sect x 3930112 sectors


Home | Main Index | Thread Index | Old Index