Port-prep archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: PCI expansion card working?
Hi! Tim,
From: Tim Rightnour <root%garbled.net@localhost>
Date: Sun, 20 Jan 2008 23:22:11 -0700 (MST)
> Just ot be sure I understand you correctly, you mean that you have a few
> different fwohci and ehci cards, and only some of them work, while others do
> not?
Yes. I have some cards. (fwohci+[eo]hci, fwohci, [eo]hci)
However, it was only a card of only of fwohci and [eo]hci that worked.
It agrees from this to Nishimura-san's opinion.
From: "Toru Nishimura" <locore64%alkyltechnology.com@localhost>
Date: Mon, 21 Jan 2008 21:23:09 +0900
> Just a wild guess; some "BIOS" (preboot program to enumerate PCI
> device and prepare various PCI matters for real OS) fail to cope with
> "two-functions-in-a-single" cards which equip two PCI device chips.
> Lately most of PC BIOS do well the job smart, however it's likely a case
> where old RISC firmware fails the similar way, I suspect.
> Yeah.. I think that panic in pcn was fixed in -current.
Thanks. I updated if_pcn.c.
> As for the card that caused the wierd hang after the cpu probe, can you boot
> that card with RESIDUAL_DATA_DUMP and see if it says anything interesting?
> (I'm not sure, that might happen too late to capture it)
Sorry. I get the boot log on com0 with PCI_CONFIGURE_DUMP only.
However, it was felt that I was strange. It hangs up when the console
is vga. However, it booted for com0 with a strange log. As many as
17 S3 86C864-1 doesn't exist in my prep. X-)
^^^^^^^^^^^^^^
typescript.now: working (fwohci, [eo]hci)
typescript.17vga: strange log with com0 (fwohci+[eo]hci, [eo]hci)
I think the slow resignation. If you want to pursue this phenomenon, I
will continue and pass you log.
Thanks,
--
kiyohara
>> NetBSD/prep BOOT, Revision 1.8
>> (builds@wb40, Thu Nov 8 01:45:46 PST 2007)
Boot:
Loading in()
2688248+208176 [172048+166967]=0x316264
start=0x100000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 4.99.49 (TEST) #0: Tue Jan 22 01:26:08 JST 2008
lance%hierophant.fool@localhost:/sys/arch/prep/compile/TEST
Model: IBM PPS Model 7248 (E)
total memory = 128 MB
avail memory = 120 MB
mainbus0 (root)
cpu0 at mainbus0: 604 (Revision 3.4), ID 0 (primary)
cpu0: HID0 c084<ICE,DCE,SGE,BHT>, powersave: 1
cpu0: 133.33 MHz
cpu at mainbus0 not configured
pnpbus0 at mainbus0
wdc0 at pnpbus0: port 0x1f0-0x1f7 0x3f6, irq 13, DMA 6
atabus0 at wdc0 channel 0
wdc1 at pnpbus0: port 0x170-0x177 0x376, irq 13, DMA 7
atabus1 at wdc1 channel 0
mcclock0 at pnpbus0: port 0x70-0x71, irq 8: mc146818 compatible time-of-day
clock
nvram0 at pnpbus0: port 0x74-0x75 0x76
pci0 at mainbus0 bus 0: indirect configuration space access
pchb0 at pci0 dev 0 function 0: PCI configuration registers:
Common header:
0x00: 0x00011057 0x00800146 0x06000024 0x00000000
Vendor Name: Motorola (0x1057)
Device Name: MPC105 "Eagle" Host Bridge (0x0001)
Command register: 0x0146
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0080
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: fast (0x0)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: host (0x00)
Interface: 0x00
Revision ID: 0x24
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00200000 0x00006040 0x00000000 0x00000000
0x90: 0x003f001f 0x00007f5f 0x00000000 0x00000000
0xa0: 0x00000035 0x00000000 0x9f071a09 0xc31b429b
0xb0: 0x00000000 0x00000000 0x01250000 0x00000000
0xc0: 0x520000a5 0x03000010 0xf8030000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0xffcb0aaa 0x00000fa2 0x0002b2dc 0x00000000
Don't know how to pretty-print device-dependent header.
Motorola MPC105 "Eagle" Host Bridge (host bridge, revision 0x24) at ? dev 0
function 0 (intrswiz 0, intrpin 0, i/o off, mem on, no quirks)
pchb0: Motorola MPC105 "Eagle" Host Bridge (rev. 0x24)
pchb0: L2 cache: 512K, write-through mode
pcib0 at pci0 dev 11 function 0: PCI configuration registers:
Common header:
0x00: 0x000a1014 0x04000147 0x06010002 0x00000000
Vendor Name: IBM (0x1014)
Device Name: Fire Coral ISA Bridge w/PnP (0x000a)
Command register: 0x0147
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0400
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: slow (0x2)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: ISA (0x01)
Interface: 0x00
Revision ID: 0x02
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x000081a1 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x000000ff
Base address register at 0x10
type: 32-bit i/o
base: 0x000081a0, size: 0x00000008
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0xff
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000100 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
IBM Fire Coral ISA Bridge w/PnP (ISA bridge, revision 0x02) at ? dev 11
function 0 (intrswiz 0, intrpin 0, i/o on, mem on, no quirks): IBM Fire Coral
ISA Bridge w/PnP (rev. 0x02)
pcn0 at pci0 dev 12 function 0: PCI configuration registers:
Common header:
0x00: 0x20001022 0x02800147 0x02000016 0x0000ff00
Vendor Name: Advanced Micro Devices (0x1022)
Device Name: PCnet-PCI Ethernet (0x2000)
Command register: 0x0147
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x16
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00008181 0x00822a00 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00800000 0x00000000 0x00000000 0xff060100
Base address register at 0x10
type: 32-bit i/o
base: 0x00008180, size: 0x00000020
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x00822a00, size: 0x00000020
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00800000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0xff
Minimum Grant: 0x06
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Advanced Micro Devices PCnet-PCI Ethernet (ethernet network, revision 0x16) at
? dev 12 function 0 (intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks): AMD
PCnet-PCI Ethernet
pcn0: Am79c970A PCnet-PCI II rev 6, Ethernet address 08:00:5a:f8:7c:23
pcn0: interrupting at irq 15
pcn0: 10base5, 10base5-FDX, 10baseT, 10baseT-FDX, auto, auto-FDX
vga0 at pci0 dev 14 function 0: PCI configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00810000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00810000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at ? dev 14 function 0 (intrswiz 0,
intrpin 0, i/o on, mem on, no quirks): S3 86C864-1 ("Vision864") (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1
direct rendering for vga0 unsupported
siop0 at pci0 dev 16 function 0: PCI configuration registers:
Common header:
0x00: 0x00011000 0x02000147 0x01000002 0x0000ff00
Vendor Name: Symbios Logic (0x1000)
Device Name: 53c810 (0x0001)
Command register: 0x0147
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: mass storage (0x01)
Subclass Name: SCSI (0x00)
Interface: 0x00
Revision ID: 0x02
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00008001 0x00822800 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x0000010f
Base address register at 0x10
type: 32-bit i/o
base: 0x00008000, size: 0x00000100
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x00822800, size: 0x00000100
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x0f
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x330000d8 0x1d000007 0x00800000 0x020f0080
0x90: 0x8021ee58 0xffffff00 0x2035f000 0x807e9560
0xa0: 0x00000000 0x98080000 0x8021e290 0x8021e290
0xb0: 0x00000050 0x200000b8 0x010000c0 0x8021e2e0
0xc0: 0x00000000 0x0f000085 0x0080000b 0x80000007
0xd0: 0xffff0000 0xffffff00 0xffff0000 0x80a45a60
0xe0: 0xffffffff 0xffffffff 0xffffffff 0xffffffff
0xf0: 0xffffffff 0xffffffff 0xffffffff 0xffffffff
Don't know how to pretty-print device-dependent header.
Symbios Logic 53c810 (SCSI mass storage, revision 0x02) at ? dev 16 function 0
(intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks): Symbios Logic 53c810
(fast scsi)
siop0: interrupting at irq 15
scsibus0 at siop0: 8 targets, 8 luns per target
ohci0 at pci0 dev 18 function 0: PCI configuration registers:
Common header:
0x00: 0x00351033 0x02100146 0x0c031041 0x0080fc08
Vendor Name: NEC (0x1033)
Device Name: USB Host Controller (0x0035)
Command register: 0x0146
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: USB (0x03)
Interface: 0x10
Revision ID: 0x41
BIST: 0x00
Header Type: 0x00+multifunction (0x80)
Latency Timer: 0xfc
Cache Line Size: 0x08
Type 0 ("normal" device) header:
0x10: 0x00820000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00351735
0x30: 0x00000000 0x00000040 0x00000000 0x2a010100
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x00820000, size: 0x00001000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1735
Subsystem ID: 0x0035
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x40
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x2a
Minimum Grant: 0x01
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x00
Capability register at 0x40
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x7e020001 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0xc4303305 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
NEC USB Host Controller (USB serial bus, interface 0x10, revision 0x41) at ?
dev 18 function 0 (intrswiz 0, intrpin 0x1, i/o off, mem on, no quirks): NEC
USB Host Controller (rev. 0x41)
ohci0: interrupting at irq 15
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
ohci1 at pci0 dev 18 function 1: PCI configuration registers:
Common header:
0x00: 0x00351033 0x02100146 0x0c031041 0x0000fc08
Vendor Name: NEC (0x1033)
Device Name: USB Host Controller (0x0035)
Command register: 0x0146
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: USB (0x03)
Interface: 0x10
Revision ID: 0x41
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xfc
Cache Line Size: 0x08
Type 0 ("normal" device) header:
0x10: 0x00821000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00351735
0x30: 0x00000000 0x00000040 0x00000000 0x2a010200
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x00821000, size: 0x00001000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1735
Subsystem ID: 0x0035
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x40
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x2a
Minimum Grant: 0x01
Interrupt pin: 0x02 (pin B)
Interrupt line: 0x00
Capability register at 0x40
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x7e020001 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
NEC USB Host Controller (USB serial bus, interface 0x10, revision 0x41) at ?
dev 18 function 1 (intrswiz 0, intrpin 0x2, i/o off, mem on, no quirks): NEC
USB Host Controller (rev. 0x41)
ohci1: interrupting at irq 15
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
ehci0 at pci0 dev 18 function 2: PCI configuration registers:
Common header:
0x00: 0x00e01033 0x02100146 0x0c032001 0x0000fc08
Vendor Name: NEC (0x1033)
Device Name: USB Host Controller (0x00e0)
Command register: 0x0146
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: USB (0x03)
Interface: 0x20
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xfc
Cache Line Size: 0x08
Type 0 ("normal" device) header:
0x10: 0x00822900 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00e01735
0x30: 0x00000000 0x00000040 0x00000000 0x22100300
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x00822900, size: 0x00000100
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1735
Subsystem ID: 0x00e0
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x40
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x22
Minimum Grant: 0x10
Interrupt pin: 0x03 (pin C)
Interrupt line: 0x00
Capability register at 0x40
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x7e020001 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x003f2020 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0xc4303305 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
NEC USB Host Controller (USB serial bus, interface 0x20, revision 0x01) at ?
dev 18 function 2 (intrswiz 0, intrpin 0x3, i/o off, mem on, no quirks): NEC
USB Host Controller (rev. 0x01)
ehci0: interrupting at irq 15
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
fwohci0 at pci0 dev 22 function 0: PCI configuration registers:
Common header:
0x00: 0x30441106 0x02100147 0x0c001043 0x0000f808
Vendor Name: VIA Technologies (0x1106)
Device Name: VT6306 IEEE 1394 Host Controller (0x3044)
Command register: 0x0147
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: Firewire (0x00)
Interface: 0x10
Revision ID: 0x43
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xf8
Cache Line Size: 0x08
Type 0 ("normal" device) header:
0x10: 0x00822000 0x00008101 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000050 0x00000000 0x00000100
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x00822000, size: 0x00000800
Base address register at 0x14
type: 32-bit i/o
base: 0x00008100, size: 0x00000080
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x50
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x00
Capability register at 0x50
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00020001 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
VIA Technologies VT6306 IEEE 1394 Host Controller (Firewire serial bus,
interface 0x10, revision 0x43) at ? dev 22 function 0 (intrswiz 0, intrpin 0x1,
i/o on, mem on, no quirks): VIA Technologies VT6306 IEEE 1394 Host Controller
(rev. 0x43)
fwohci0: interrupting at irq 15
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 0c:10:11:00:00:00:04:6d
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S100, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip at ieee1394if0 not configured
fwohci0: Initiate bus reset
isa0 at pcib0
lpt0 at isa0 port 0x3bc-0x3bf irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
spkr0 at pcppi0
isabeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
pcppi0: attached to attimer0
wss0 at isapnp0 port 0x534/4,0x388/4,0x220/16 irq 5 drq 1,0
wss0: Crystal CS4232 Sound Chip : broken
audio0 at wss0: full duplex, mmap
opl at wss0 not configured
isapnp0: <Crystal CS4232 Sound Chip, CSC0001, , > port 0x200/8 not configured
isapnp0: <Crystal CS4232 Sound Chip, CSC0002, , 4232> port 0x10/8 not configured
isapnp0: <Crystal CS4232 Sound Chip, CSC0003, , > port 0x330/2 irq 9 not
configured
isapnp0: <Crystal CS4232 Sound Chip, CSC0004, , CD-ROM> port 0x10/4 not
configured
biomask 80000ce netmask 80000ce ttymask 80000ce
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <CONNER, CFP2105S 2.14GB, 1524> disk fixed
sd0: 2048 MB, 3940 cyl, 10 head, 106 sec, 512 bytes/sect x 4194304 sectors
sd0: sync (100.00ns offset 8), 8-bit (10.000MB/s) transfers, tagged queueing
cd0 at scsibus0 target 3 lun 0: <IBM, CDRM00203\000\000\000\000\000!K, BZ26>
cdrom removable
cd0: sync (200.00ns offset 8), 8-bit (5.000MB/s) transfers
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
Mon Jan 21 16:39:49 GMT 2008
swapctl: adding /dev/sd0b as swap device at priority 0
Checking for botched superblock upgrades: done.
Starting file system checks:
/dev/rsd0a: file system is clean; not checking
/dev/rsd0f: file system is clean; not checking
/dev/rsd0g: file system is clean; not checking
Setting tty flags.
Setting sysctl variables:
Starting network.
Hostname: justice.fool
IPv6 mode: host
Configuring network interfaces: pcn0.
add net default: gateway 192.168.1.21
Adding interface aliases:
Building databases...
Starting syslogd.
Checking for core dump...
savecore: can't find device 1465/105919
Jan 22 01:39:59 justice savecore: can't find device 1465/105919
Setting date via ntp.
Mounting all filesystems...
Clearing /tmp.
Checking quotas: done.
Setting securelevel: kern.securelevel: 0 -> 1
Starting virecover.
Starting local daemons:.
Updating motd.
Starting sshd.
postfix/postfix-script: starting the Postfix mail system
Starting cron.
Tue Jan 22 01:40:16 JST 2008
NetBSD/prep (justice.fool) (tty00)
login:
>> NetBSD/prep BOOT, Revision 1.8
>> (builds@wb40, Thu Nov 8 01:45:46 PST 2007)
Boot:
Loading in()
2689504+208136 [172224+167077]=0x316844
start=0x100000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 4.99.49 (TEST) #0: Tue Jan 22 02:38:07 JST 2008
lance%hierophant.fool@localhost:/sys/arch/prep/compile/TEST
Model: IBM PPS Model 7248 (E)
total memory = 128 MB
avail memory = 120 MB
mainbus0 (root)
cpu0 at mainbus0: 604 (Revision 3.4), ID 0 (primary)
cpu0: HID0 c084<ICE,DCE,SGE,BHT>, powersave: 1
cpu0: 133.33 MHz
cpu at mainbus0 not configured
Couldn't find PNP data for bus 0 devfunc 0xb0
pnpbus0 at mainbus0
wdc0 at pnpbus0: port 0x1f0-0x1f7 0x3f6, irq 13, DMA 6
atabus0 at wdc0 channel 0
wdc1 at pnpbus0: port 0x170-0x177 0x376, irq 13, DMA 7
atabus1 at wdc1 channel 0
mcclock0 at pnpbus0: port 0x70-0x71, irq 8: mc146818 compatible time-of-day
clock
nvram0 at pnpbus0: port 0x74-0x75 0x76
pci0 at mainbus0 bus 0: indirect configuration space access
pchb0 at pci0 dev 0 function 0: PCI configuration registers:
Common header:
0x00: 0x00011057 0x00800146 0x06000024 0x00000000
Vendor Name: Motorola (0x1057)
Device Name: MPC105 "Eagle" Host Bridge (0x0001)
Command register: 0x0146
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0080
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: fast (0x0)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: host (0x00)
Interface: 0x00
Revision ID: 0x24
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00200000 0x00006040 0x00000000 0x00000000
0x90: 0x003f001f 0x00007f5f 0x00000000 0x00000000
0xa0: 0x00000035 0x00000000 0x9f071a09 0xc31b429b
0xb0: 0x00000000 0x00000000 0x01250000 0x00000000
0xc0: 0x520000a5 0x03000010 0xf8030000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0xffcb0aaa 0x00000fa2 0x0002b2dc 0x00000000
Don't know how to pretty-print device-dependent header.
Motorola MPC105 "Eagle" Host Bridge (host bridge, revision 0x24) at ? dev 0
function 0 (intrswiz 0, intrpin 0, i/o off, mem on, no quirks)
pchb0: Motorola MPC105 "Eagle" Host Bridge (rev. 0x24)
pchb0: L2 cache: 512K, write-through mode
pcib0 at pci0 dev 11 function 0: PCI configuration registers:
Common header:
0x00: 0x000a1014 0x04000147 0x06010002 0x00000000
Vendor Name: IBM (0x1014)
Device Name: Fire Coral ISA Bridge w/PnP (0x000a)
Command register: 0x0147
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0400
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: slow (0x2)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: ISA (0x01)
Interface: 0x00
Revision ID: 0x02
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00008121 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x000000ff
Base address register at 0x10
type: 32-bit i/o
base: 0x00008120, size: 0x00000008
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0xff
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000100 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
IBM Fire Coral ISA Bridge w/PnP (ISA bridge, revision 0x02) at ? dev 11
function 0 (intrswiz 0, intrpin 0, i/o on, mem on, no quirks): IBM Fire Coral
ISA Bridge w/PnP (rev. 0x02)
pcn0 at pci0 dev 12 function 0: PCI configuration registers:
Common header:
0x00: 0x20001022 0x02800147 0x02000016 0x0000ff00
Vendor Name: Advanced Micro Devices (0x1022)
Device Name: PCnet-PCI Ethernet (0x2000)
Command register: 0x0147
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x16
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00008101 0x08b22200 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x08b00000 0x00000000 0x00000000 0xff060100
Base address register at 0x10
type: 32-bit i/o
base: 0x00008100, size: 0x00000020
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x08b22200, size: 0x00000020
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x08b00000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0xff
Minimum Grant: 0x06
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Advanced Micro Devices PCnet-PCI Ethernet (ethernet network, revision 0x16) at
? dev 12 function 0 (intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks): AMD
PCnet-PCI Ethernet
pcn0: Am79c970A PCnet-PCI II rev 6, Ethernet address 08:00:5a:f8:7c:23
pcn0: interrupting at irq 15
pcn0: 10base5, 10base5-FDX, 10baseT, 10baseT-FDX, auto, auto-FDX
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci0 dev 14 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci0 dev 14 function 0 (intrswiz
0, intrpin 0, i/o on, mem on, no quirks) not configured
siop0 at pci0 dev 16 function 0: PCI configuration registers:
Common header:
0x00: 0x00011000 0x02000147 0x01000002 0x0000ff00
Vendor Name: Symbios Logic (0x1000)
Device Name: 53c810 (0x0001)
Command register: 0x0147
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: mass storage (0x01)
Subclass Name: SCSI (0x00)
Interface: 0x00
Revision ID: 0x02
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xff
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00008001 0x08b22000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x0000010f
Base address register at 0x10
type: 32-bit i/o
base: 0x00008000, size: 0x00000100
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0x08b22000, size: 0x00000100
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x0f
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x330000d8 0x1d000007 0x00800000 0x020f0080
0x90: 0x8023ac78 0xffffff00 0x2035f000 0x807e9560
0xa0: 0x00000000 0x98080000 0x8023a0b0 0x8023a0b0
0xb0: 0x00000050 0x200000b8 0x010000c0 0x8023a100
0xc0: 0x00000000 0x0f000049 0x0080000b 0x80000007
0xd0: 0xffff0000 0xffffff00 0xffff0000 0x808b8cf8
0xe0: 0xffffffff 0xffffffff 0xffffffff 0xffffffff
0xf0: 0xffffffff 0xffffffff 0xffffffff 0xffffffff
Don't know how to pretty-print device-dependent header.
Symbios Logic 53c810 (SCSI mass storage, revision 0x02) at ? dev 16 function 0
(intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks): Symbios Logic 53c810
(fast scsi)
siop0: interrupting at irq 15
scsibus0 at siop0: 8 targets, 8 luns per target
ohci0 at pci0 dev 18 function 0: PCI configuration registers:
Common header:
0x00: 0x00351033 0x02100146 0x0c031041 0x0080fc08
Vendor Name: NEC (0x1033)
Device Name: USB Host Controller (0x0035)
Command register: 0x0146
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: USB (0x03)
Interface: 0x10
Revision ID: 0x41
BIST: 0x00
Header Type: 0x00+multifunction (0x80)
Latency Timer: 0xfc
Cache Line Size: 0x08
Type 0 ("normal" device) header:
0x10: 0x08b20000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00351735
0x30: 0x00000000 0x00000040 0x00000000 0x2a010100
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x08b20000, size: 0x00001000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1735
Subsystem ID: 0x0035
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x40
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x2a
Minimum Grant: 0x01
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x00
Capability register at 0x40
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x7e020001 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0xc4303305 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
NEC USB Host Controller (USB serial bus, interface 0x10, revision 0x41) at ?
dev 18 function 0 (intrswiz 0, intrpin 0x1, i/o off, mem on, no quirks): NEC
USB Host Controller (rev. 0x41)
ohci0: interrupting at irq 15
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
ohci1 at pci0 dev 18 function 1: PCI configuration registers:
Common header:
0x00: 0x00351033 0x02100146 0x0c031041 0x0000fc08
Vendor Name: NEC (0x1033)
Device Name: USB Host Controller (0x0035)
Command register: 0x0146
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: USB (0x03)
Interface: 0x10
Revision ID: 0x41
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xfc
Cache Line Size: 0x08
Type 0 ("normal" device) header:
0x10: 0x08b21000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00351735
0x30: 0x00000000 0x00000040 0x00000000 0x2a010200
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x08b21000, size: 0x00001000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1735
Subsystem ID: 0x0035
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x40
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x2a
Minimum Grant: 0x01
Interrupt pin: 0x02 (pin B)
Interrupt line: 0x00
Capability register at 0x40
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x7e020001 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
NEC USB Host Controller (USB serial bus, interface 0x10, revision 0x41) at ?
dev 18 function 1 (intrswiz 0, intrpin 0x2, i/o off, mem on, no quirks): NEC
USB Host Controller (rev. 0x41)
ohci1: interrupting at irq 15
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
ehci0 at pci0 dev 18 function 2: PCI configuration registers:
Common header:
0x00: 0x00e01033 0x02100146 0x0c032001 0x0000fc08
Vendor Name: NEC (0x1033)
Device Name: USB Host Controller (0x00e0)
Command register: 0x0146
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: USB (0x03)
Interface: 0x20
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0xfc
Cache Line Size: 0x08
Type 0 ("normal" device) header:
0x10: 0x08b22100 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00e01735
0x30: 0x00000000 0x00000040 0x00000000 0x22100300
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x08b22100, size: 0x00000100
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1735
Subsystem ID: 0x00e0
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x40
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x22
Minimum Grant: 0x10
Interrupt pin: 0x03 (pin C)
Interrupt line: 0x00
Capability register at 0x40
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x7e020001 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x003f2020 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0xc4303305 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
NEC USB Host Controller (USB serial bus, interface 0x20, revision 0x01) at ?
dev 18 function 2 (intrswiz 0, intrpin 0x3, i/o off, mem on, no quirks): NEC
USB Host Controller (rev. 0x01)
ehci0: interrupting at irq 15
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
ppb0 at pci0 dev 22 function 0: PCI configuration registers:
Common header:
0x00: 0x00213388 0x02900147 0x06040013 0x0001ff08
Vendor Name: HiNT (0x3388)
Device Name: HB1 PCI-PCI Bridge (0x0021)
Command register: 0x0147
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: on
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0290
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: PCI (0x04)
Interface: 0x00
Revision ID: 0x13
BIST: 0x00
Header Type: 0x01 (0x01)
Latency Timer: 0xff
Cache Line Size: 0x08
Type 1 (PCI-PCI bridge) header:
0x10: 0x00000000 0x00000000 0x00010100 0x22800111
0x20: 0x08000000 0x08a10891 0x08900000 0x08afffff
0x30: 0x00000000 0x00000080 0x00000000 0x000300ff
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Primary bus number: 0x00
Secondary bus number: 0x01
Subordinate bus number: 0x01
Secondary bus latency timer: 0x00
Secondary status register: 0x2280
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Signaled Target Abort: off
Received Target Abort: off
Received Master Abort: on
System Error: off
Parity Error: off
I/O region:
base register: 0x11
limit register: 0x01
base upper 16 bits register: 0x0000
limit upper 16 bits register: 0x0000
Memory region:
base register: 0x0000
limit register: 0x0800
Prefetchable memory region:
base register: 0x0891
limit register: 0x08a1
base upper 32 bits register: 0x08900000
limit upper 32 bits register: 0x08afffff
Capability list pointer: 0x80
Expansion ROM Base Address: 0x00000000
Interrupt line: 0xff
Interrupt pin: 0x00 (none)
Bridge control register: 0x0003
Parity error response: on
Secondary SERR forwarding: on
ISA enable: off
VGA enable: off
Master abort reporting: off
Secondary bus reset: off
Fast back-to-back capable: off
Capability register at 0x80
type: 0x01 (Power Management, rev. 1.0)
Capability register at 0x90
type: 0x06 (CompactPCI Hot-swapping)
Capability register at 0xa0
type: 0x03 (VPD)
Device-dependent header:
0x40: 0x02000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0xf6029001 0x00c00000 0x00000000 0x00000000
0x90: 0x0000a006 0x00000000 0x00000000 0x00000000
0xa0: 0x80000003 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00111109 0xffff0004 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00213388 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
HiNT HB1 PCI-PCI Bridge (PCI bridge, revision 0x13) at ? dev 22 function 0
(intrswiz 0, intrpin 0, i/o on, mem on, no quirks): HiNT HB1 PCI-PCI Bridge
(rev. 0x13)
pci1 at ppb0 bus 1
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 8 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 8 function 0 (intrswiz
0x8, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 9 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 9 function 0 (intrswiz
0x9, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 10 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 10 function 0 (intrswiz
0xa, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 11 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 11 function 0 (intrswiz
0xb, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 12 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 12 function 0 (intrswiz
0xc, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 13 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 13 function 0 (intrswiz
0xd, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 14 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 14 function 0 (intrswiz
0xe, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 15 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 15 function 0 (intrswiz
0xf, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 24 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 24 function 0 (intrswiz
0x18, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 25 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 25 function 0 (intrswiz
0x19, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 26 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 26 function 0 (intrswiz
0x1a, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 27 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 27 function 0 (intrswiz
0x1b, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 28 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 28 function 0 (intrswiz
0x1c, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 29 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 29 function 0 (intrswiz
0x1d, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 30 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 30 function 0 (intrswiz
0x1e, intrpin 0, i/o on, mem on, no quirks) not configured
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 31 function 0: PCI
configuration registers:
Common header:
0x00: 0x88c15333 0x02000003 0x00010000 0x00000000
Vendor Name: S3 (0x5333)
Device Name: 86C864-1 ("Vision864") (0x88c1)
Command register: 0x0003
I/O space accesses: on
Memory space accesses: on
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Interrupt disable: off
Status register: 0x0200
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: prehistoric (0x00)
Subclass Name: VGA (0x01)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x07800000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x089f0000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0x07800000, size: 0x00800000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x089f0000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
S3 86C864-1 ("Vision864") (VGA prehistoric) at pci1 dev 31 function 0 (intrswiz
0x1f, intrpin 0, i/o on, mem on, no quirks) not configured
isa0 at pcib0
lpt0 at isa0 port 0x3bc-0x3bf irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
spkr0 at pcppi0
isabeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
pcppi0: attached to attimer0
wss0 at isapnp0 port 0x534/4,0x388/4,0x220/16 irq 5 drq 1,0
wss0: Crystal CS4232 Sound Chip : broken
audio0 at wss0: full duplex, mmap
opl at wss0 not configured
isapnp0: <Crystal CS4232 Sound Chip, CSC0001, , > port 0x200/8 not configured
isapnp0: <Crystal CS4232 Sound Chip, CSC0002, , 4232> port 0x10/8 not configured
isapnp0: <Crystal CS4232 Sound Chip, CSC0003, , > port 0x330/2 irq 9 not
configured
isapnp0: <Crystal CS4232 Sound Chip, CSC0004, , CD-ROM> port 0x10/4 not
configured
biomask 800004e netmask 800004e ttymask 800004e
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 0 lun 0: <CONNER, CFP2105S 2.14GB, 1524> disk fixed
sd0: 2048 MB, 3940 cyl, 10 head, 106 sec, 512 bytes/sect x 4194304 sectors
sd0: sync (100.00ns offset 8), 8-bit (10.000MB/s) transfers, tagged queueing
cd0 at scsibus0 target 3 lun 0: <IBM, CDRM00203\000\000\000\000\000!K, BZ26>
cdrom removable
cd0: sync (200.00ns offset 8), 8-bit (5.000MB/s) transfers
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
Mon Jan 21 17:47:08 GMT 2008
swapctl: adding /dev/sd0b as swap device at priority 0
Checking for botched superblock upgrades: done.
Starting file system checks:
/dev/rsd0a: file system is clean; not checking
/dev/rsd0f: file system is clean; not checking
/dev/rsd0g: file system is clean; not checking
Setting tty flags.
Setting sysctl variables:
Starting network.
Hostname: justice.fool
IPv6 mode: host
Configuring network interfaces: pcn0.
add net default: gateway 192.168.1.21
Adding interface aliases:
Building databases...
Starting syslogd.
Checking for core dump...
savecore: /dev/wd0a: Device not configured
Jan 22 02:47:18 justice savecore: /dev/wd0a: Device not configured
Setting date via ntp.
Mounting all filesystems...
Clearing /tmp.
Checking quotas: done.
Setting securelevel: kern.securelevel: 0 -> 1
Starting virecover.
Starting local daemons:.
Updating motd.
Starting sshd.
postfix/postfix-script: starting the Postfix mail system
Starting cron.
Tue Jan 22 02:47:34 JST 2008
NetBSD/prep (justice.fool) (tty00)
login:
Home |
Main Index |
Thread Index |
Old Index