Re: wd0 dos error

[Philip Miller <sighoya%gmail.com@localhost>]

On 03/01/13 22:10, matthew green wrote:
> > wd0(ixpide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
> ah, this is probably fixable by changing your BIOS to use AHCI
> instead of IDE.
>
> (we really need to fix ixpide in this situation.)
>
>
> .mrg.
Yes this works without errors. dmesg:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.0.1 (GENERIC)
total memory = 6140 MB
avail memory = 5947 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Gigabyte Technology Co., Ltd. GA-890XA-UD3 ( )
mainbus0 (root)
cpu0 at mainbus0 apid 0: AMD Phenom(tm) II X6 1090T Processor, id 0x100fa0
cpu1 at mainbus0 apid 1: AMD Phenom(tm) II X6 1090T Processor, id 0x100fa0
cpu2 at mainbus0 apid 2: AMD Phenom(tm) II X6 1090T Processor, id 0x100fa0
cpu3 at mainbus0 apid 3: AMD Phenom(tm) II X6 1090T Processor, id 0x100fa0
cpu4 at mainbus0 apid 4: AMD Phenom(tm) II X6 1090T Processor, id 0x100fa0
cpu5 at mainbus0 apid 5: AMD Phenom(tm) II X6 1090T Processor, id 0x100fa0
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 21, 24 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <GBT   ,GBTUACPI,42302e31>, AslId <GBTU,01010101>
ACPI: Actual Package length (1) is larger than NumElements field (0), 
truncated

ACPI: Actual Package length (1) is larger than NumElements field (0), 
truncated

ACPI: Actual Package length (1) is larger than NumElements field (0), 
truncated

ACPI: Actual Package length (1) is larger than NumElements field (0), 
truncated

acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
SYSR (PNP0C02) at acpi0 not configured
PMIO (PNP0C02) at acpi0 not configured
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
FDC0 (PNP0700) at acpi0 not configured
UAR1 (PNP0501) at acpi0 not configured
EXPL (PNP0C02) at acpi0 not configured
MEM (PNP0C01) at acpi0 not configured
acpiwmi0 at acpi0 (AOD, PNP0C14-0): ACPI WMI Interface
acpiwmibus at acpiwmi0 not configured
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x1002 product 0x5958 (rev. 0x00)
ppb0 at pci0 dev 2 function 0: vendor 0x1002 product 0x5978 (rev. 0x00)
ppb0: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci1 dev 0 function 0: vendor 0x10de product 0x0f00 (rev. 0xa1)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
hdaudio0 at pci1 dev 0 function 1: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 19
hdafg0 at hdaudio0: NVIDIA product 0014
hdafg0: DP00 8ch: Digital Out [Jack]
hdafg0: 8ch/0ch 48000Hz PCM16*
hdafg1 at hdaudio0: NVIDIA product 0014
hdafg1: DP00 8ch: Digital Out [Jack]
hdafg1: 8ch/0ch 48000Hz PCM16*
hdafg2 at hdaudio0: NVIDIA product 0014
hdafg2: DP00 8ch: Digital Out [Jack]
hdafg2: 8ch/0ch 48000Hz PCM16*
hdafg3 at hdaudio0: NVIDIA product 0014
hdafg3: DP00 8ch: Digital Out [Jack]
hdafg3: 8ch/0ch 48000Hz PCM16*
ppb1 at pci0 dev 6 function 0: vendor 0x1002 product 0x597c (rev. 0x00)
ppb1: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
jmide0 at pci2 dev 0 function 0: vendor 0x197b product 0x2363 (rev. 0x03)
jmide0: 1 PATA port, 2 SATA ports
jmide0: interrupting at ioapic0 pin 18
ahcisata0 at jmide0
ahcisata0: AHCI revision 1.0, 2 ports, 32 slots, CAP 
0xc722ff01<PSC,SSC,PMD,SPM,ISS=0x2=Gen2,SCLO,SAL,SALP,SNCQ,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
jmide0: PCI IDE interface used
jmide0: bus-master DMA support present
jmide0: primary channel wired to native-PCI mode
jmide0: primary channel is unused
jmide0: secondary channel wired to native-PCI mode
jmide0: secondary channel is PATA
atabus2 at jmide0 channel 1
ppb2 at pci0 dev 7 function 0: vendor 0x1002 product 0x597d (rev. 0x00)
ppb2: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
vendor 0x1033 product 0x0194 (USB serial bus, interface 0x30, revision 
0x03) at pci3 dev 0 function 0 not configured
ppb3 at pci0 dev 10 function 0: vendor 0x1002 product 0x597f (rev. 0x00)
ppb3: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci4 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet 
(rev. 0x03)
re0: interrupting at ioapic0 pin 18
re0: Ethernet address 6c:f0:49:e7:58:43
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ahcisata1 at pci0 dev 17 function 0: vendor 0x1002 product 0x4391 (rev. 
0x40)
ahcisata1: interrupting at ioapic0 pin 19
ahcisata1: 64-bit DMA
ahcisata1: AHCI revision 1.20, 6 ports, 32 slots, CAP 
0xf732ff05<PSC,SSC,PMD,SPM,ISS=0x3=Gen3,SCLO,SAL,SALP,SMPS,SSNTF,SNCQ,S64A>
atabus3 at ahcisata1 channel 0
atabus4 at ahcisata1 channel 1
atabus5 at ahcisata1 channel 2
atabus6 at ahcisata1 channel 3
atabus7 at ahcisata1 channel 4
atabus8 at ahcisata1 channel 5
ohci0 at pci0 dev 18 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 18
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at pci0 dev 18 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci0: interrupting at ioapic0 pin 17
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controller, 5 ports each: ohci0
usb1 at ehci0: USB revision 2.0
ohci1 at pci0 dev 19 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 18
ohci1: OHCI version 1.0, legacy support
usb2 at ohci1: USB revision 1.0
ehci1 at pci0 dev 19 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci1: interrupting at ioapic0 pin 17
ehci1: dropped intr workaround enabled
ehci1: EHCI version 1.0
ehci1: companion controller, 5 ports each: ohci1
usb3 at ehci1: USB revision 2.0
piixpm0 at pci0 dev 20 function 0: vendor 0x1002 product 0x4385 (rev. 0x41)
piixpm0: polling (SB800)
iic0 at piixpm0: I2C bus
hdaudio1 at pci0 dev 20 function 2: HD Audio Controller
hdaudio1: interrupting at ioapic0 pin 16
hdafg4 at hdaudio1: Realtek ALC892
hdafg4: DAC00 8ch: Speaker [Jack]
hdafg4: DAC01 2ch: HP Out [Jack]
hdafg4: DIG02 2ch: SPDIF Out [Jack]
hdafg4: DIG03 2ch: SPDIF Out [Built-In]
hdafg4: ADC04 2ch: Line In [Jack], Mic In [Jack]
hdafg4: ADC05 2ch: Mic In [Jack]
hdafg4: DIG-In06 2ch: SPDIF In [Jack]
hdafg4: 8ch/2ch 32000Hz 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 
PCM20 PCM24 AC3
audio0 at hdafg4: full duplex, playback, capture, independent
pcib0 at pci0 dev 20 function 3: vendor 0x1002 product 0x439d (rev. 0x40)
ppb4 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x40)
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled
rtk0 at pci5 dev 6 function 0: D-Link Systems DFE 530TX+ (rev. 0x10)
rtk0: interrupting at ioapic0 pin 20
rtk0: Ethernet address 00:0d:88:2a:c7:17
rlphy0 at rtk0 phy 7: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vendor 0x14f1 product 0x8800 (video multimedia, revision 0x05) at pci5 
dev 7 function 0 not configured
vendor 0x14f1 product 0x8801 (miscellaneous multimedia, revision 0x05) 
at pci5 dev 7 function 1 not configured
vendor 0x14f1 product 0x8802 (miscellaneous multimedia, revision 0x05) 
at pci5 dev 7 function 2 not configured
vendor 0x14f1 product 0x8804 (miscellaneous multimedia, revision 0x05) 
at pci5 dev 7 function 4 not configured
fwohci0 at pci5 dev 14 function 0: vendor 0x104c product 0x8024 (rev. 0x00)
fwohci0: interrupting at ioapic0 pin 22
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:e9:af:33:00:6c:f0:49
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
ohci2 at pci0 dev 20 function 5: vendor 0x1002 product 0x4399 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2: OHCI version 1.0, legacy support
usb4 at ohci2: USB revision 1.0
ppb5 at pci0 dev 21 function 0: vendor 0x1002 product 0x43a0 (rev. 0x00)
ppb5: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci6 at ppb5 bus 6
pci6: i/o space, memory space enabled, rd/line, wr/inv ok
jmide1 at pci6 dev 0 function 0: vendor 0x197b product 0x2363 (rev. 0x02)
jmide1: 1 PATA port, 2 SATA ports
jmide1: interrupting at ioapic0 pin 17
ahcisata2 at jmide1
ahcisata2: AHCI revision 1.0, 2 ports, 32 slots, CAP 
0xc722ff01<PSC,SSC,PMD,SPM,ISS=0x2=Gen2,SCLO,SAL,SALP,SNCQ,S64A>
atabus9 at ahcisata2 channel 0
atabus10 at ahcisata2 channel 1
jmide2 at pci6 dev 0 function 1: vendor 0x197b product 0x2363 (rev. 0x02)
jmide2: 1 PATA port, 2 SATA ports
jmide2: interrupting at ioapic0 pin 17
jmide2: PCI IDE interface used
jmide2: bus-master DMA support present
jmide2: primary channel wired to native-PCI mode
jmide2: primary channel is PATA
atabus11 at jmide2 channel 0
jmide2: secondary channel wired to native-PCI mode
jmide2: secondary channel is SATA
atabus12 at jmide2 channel 1
ohci3 at pci0 dev 22 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci3: interrupting at ioapic0 pin 18
ohci3: OHCI version 1.0, legacy support
usb5 at ohci3: USB revision 1.0
ehci2 at pci0 dev 22 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci2: interrupting at ioapic0 pin 17
ehci2: dropped intr workaround enabled
ehci2: EHCI version 1.0
ehci2: companion controller, 4 ports each: ohci3
usb6 at ehci2: USB revision 2.0
pchb1 at pci0 dev 24 function 0: vendor 0x1022 product 0x1200 (rev. 0x00)
pchb2 at pci0 dev 24 function 1: vendor 0x1022 product 0x1201 (rev. 0x00)
pchb3 at pci0 dev 24 function 2: vendor 0x1022 product 0x1202 (rev. 0x00)
pchb4 at pci0 dev 24 function 3: vendor 0x1022 product 0x1203 (rev. 0x00)
amdtemp0 at pchb4: AMD CPU Temperature Sensors (Family10h)
pchb5 at pci0 dev 24 function 4: vendor 0x1022 product 0x1204 (rev. 0x00)
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: HLT, lat   0 us, pow     0 mW
acpicpu0: P0: FFH, lat   4 us, pow 20150 mW, 3200 MHz
acpicpu0: P1: FFH, lat   4 us, pow 14917 mW, 2400 MHz
acpicpu0: P2: FFH, lat   4 us, pow 10500 mW, 1600 MHz
acpicpu0: P3: FFH, lat   4 us, pow  6492 mW,  800 MHz
acpicpu1 at cpu1: ACPI CPU
acpicpu2 at cpu2: ACPI CPU
acpicpu3 at cpu3: ACPI CPU
acpicpu4 at cpu4: ACPI CPU
acpicpu5 at cpu5: ACPI CPU
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 3214772910 Hz quality 3000
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
uhub0 at usb2: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 5 ports with 5 removable, self powered
uhub1 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 5 ports with 5 removable, self powered
uhub2 at usb6: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
uhub3 at usb1: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 5 ports with 5 removable, self powered
uhub4 at usb5: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 4 ports with 4 removable, self powered
uhub5 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb3: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 5 ports with 5 removable, self powered
ahcisata1 port 0: device present, speed: 3.0Gb/s
ahcisata1 port 1: device present, speed: 3.0Gb/s
ahcisata1 port 2: device present, speed: 3.0Gb/s
ahcisata1 port 3: device present, speed: 6.0Gb/s
wd0 at atabus3 drive 0
wd0: <WDC WD5000AAJS-00A8B0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ahcisata1:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 
(Ultra/133) (using DMA)
wd1 at atabus4 drive 0
wd1: <WDC WD5000AAKS-00UU3A0>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(ahcisata1:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 
(Ultra/133) (using DMA)
wd2 at atabus5 drive 0
wd2: <WDC WD5000AAKS-00UU3A0>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd2(ahcisata1:2:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 
(Ultra/133) (using DMA)
wd3 at atabus6 drive 0
wd3: <OCZ-AGILITY3>
wd3: drive supports 16-sector PIO transfers, LBA48 addressing
wd3: 57241 MB, 116301 cyl, 16 head, 63 sec, 512 bytes/sect x 117231408 
sectors
wd3: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd3(ahcisata1:3:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 
(Ultra/133) (using DMA)
atapibus0 at atabus11: 2 targets
cd0 at atapibus0 drive 0: <TSSTcorp CDDVDW SH-S222A, , SB02> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
cd0(jmide2:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
ulpt0 at uhub2 port 1 configuration 1 interface 1
ulpt0: Samsung SCX-4623 Series, rev 2.00/1.00, addr 2, iclass 7/1
ulpt0: using bi-directional mode
umass0 at uhub3 port 2 configuration 1 interface 0
umass0: JMicron Usb production, rev 2.00/0.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <Disk, Name, 01.0> disk fixed
sd0: 298 GB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: Microsoft Basic Optical Mouse, rev 1.10/0.00, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir
wsmouse0 at ums0 mux 0
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
uhidev1 at uhub4 port 2 configuration 1 interface 0
uhidev1: Cherry Mikroschalter product 0x0023, rev 2.00/2.20, addr 2, 
iclass 3/1
ukbd0 at uhidev1
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev2 at uhub4 port 2 configuration 1 interface 1
uhidev2: Cherry Mikroschalter product 0x0023, rev 2.00/2.20, addr 2, 
iclass 3/0
uhidev2: 2 report ids
uhid0 at uhidev2 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev2 reportid 2: input=1, output=0, feature=0
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)


Info: Troxel has redirected this PR to netbsd-users, don't know why.