NetBSD-Users archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: troobleshot X
Cyrille Vladimirov a écrit :
Seems like NetBSD does not recognizes your video card correctly.
What is dmesg output?
Cyrille
-----Original Message-----
From: netbsd-users-owner%NetBSD.org@localhost
[mailto:netbsd-users-owner%NetBSD.org@localhost] On Behalf Of Morgan M.C.M-L
Sent: Saturday, December 19, 2009 8:34 PM
To: netbsd-users%NetBSD.org@localhost
Subject: troobleshot X
Hello
I've finished an Acer Laptop installation but X gives me vertical lines
of red and black.
I've done this :
X -configure
vi /root/xorg.conf.new and i've writen this wich is my favorite way to
work out my screen:
HorizSync 31.5 - 48.0
VertRefresh 59.0 - 75.0
X -config /root/xorg.conf.new gave me vertical red an black lines and
freeze the lapptop.
Modifying [Driver "via" by "vesa"] gives me :
Vesa no matching modes
Screen found but bobe have a usable configuration
Any ideas ? Horiz and VertRefresh does match on slackware and
backtrack... Thanx.
Hello Cyrille. Thank You for your answer, I'm late because I was on
hollydays.
So, my graphic is a VIA, I'm sure, and here are 'dmesg.txt' and
'xorg.conf.new'
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 5.0.1 (GENERIC) #0: Thu Jul 30 01:39:11 UTC 2009
builds%b8.netbsd.org@localhost:/home/builds/ab/netbsd-5-0-1-RELEASE/i386/200907292356Z-obj/home/builds/ab/netbsd-5-0-1-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 702 MB
avail memory = 678 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Acer,Inc. Aspire 1350 (3A24)
mainbus0 (root)
cpu0 at mainbus0: AMD 686-class, 796MHz, id 0x6a0
cpu0: AMD Powernow! K7 Technology 1716 MHz
cpu0: frequencies available (Mhz): 1188 1320 1452 1584 1716
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <PTLTD , RSDT ,06040000>, AslId < LTP,00000000>
LNKA: ACPI: Found matching pin for 0.16.INTA at func 0: 0
LNKB: ACPI: Found matching pin for 0.16.INTB at func 1: 0
LNKC: ACPI: Found matching pin for 0.16.INTC at func 2: 0
LNKD: ACPI: Found matching pin for 0.16.INTD at func 3: 0
LNKA: ACPI: Found matching pin for 0.17.INTA at func 1: 0
LNKC: ACPI: Found matching pin for 0.17.INTC at func 5: 9
LNKA: ACPI: Found matching pin for 0.18.INTA at func 0: 4
LNKB: ACPI: Found matching pin for 0.7.INTA at func 0: 255
LNKB: ACPI: Found matching pin for 0.8.INTA at func 0: 5
acpi0: SCI interrupting at int 10
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (BAT1, PNP0C0A-1): ACPI Battery (Control Method)
npx1 at acpi0 (COPR, PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
pckbc1 at acpi0 (KBC0, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (MSE0, PNP0F13): aux port
pckbc2: irq 12
LPTB (PNP0400) at acpi0 not configured
FDC (PNP0700) at acpi0 not configured
FIR (NSC6001) at acpi0 not configured
acpiec0 at acpi0 (EC0, PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
acpibut1 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpitz0 at acpi0 (THRM): critical 87.0C passive 52.0C, passive cooling
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pms0: Synaptics touchpad version 5.8
pms0: Up/down buttons, Palm detect, Multi-finger
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1106 product 0x3205 (rev. 0x00)
agp0 at pchb0 (v3): aperture at 0xe0000000, size 0x10000000
ppb0 at pci0 dev 1 function 0: vendor 0x1106 product 0xb168 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: vendor 0x1106 product 0x7205 (rev. 0x01)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
cbb0 at pci0 dev 7 function 0: vendor 0x104c product 0xac50 (rev. 0x02)
fwohci0 at pci0 dev 8 function 0: vendor 0x104c product 0x8026 (rev. 0x00)
fwohci0: interrupting at irq 5
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:c0:9f:00:00:15:96:b9
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
uhci0 at pci0 dev 16 function 0: vendor 0x1106 product 0x3038 (rev. 0x80)
uhci0: interrupting at irq 4
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 16 function 1: vendor 0x1106 product 0x3038 (rev. 0x80)
uhci1: interrupting at irq 5
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 16 function 2: vendor 0x1106 product 0x3038 (rev. 0x80)
uhci2: interrupting at irq 9
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 16 function 3: vendor 0x1106 product 0x3104 (rev. 0x82)
ehci0: interrupting at irq 11
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
pcib0 at pci0 dev 17 function 0
pcib0: vendor 0x1106 product 0x3177 (rev. 0x00)
viaide0 at pci0 dev 17 function 1
viaide0: VIA Technologies VT8235 ATA133 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
auvia0 at pci0 dev 17 function 5: VIA Technologies VT8235 AC'97 Audio (rev 0x50)
auvia0: interrupting at irq 9
auvia0: ac97: Avance Logic ALC202 codec; headphone, 20 bit DAC, 18 bit ADC,
Realtek 3D
auvia0: ac97: ext id 607<AC97_22,AMAP,SPDIF,DRA,VRA>
audio0 at auvia0: full duplex, mmap, independent
vendor 0x1106 product 0x3068 (miscellaneous communications, revision 0x80) at
pci0 dev 17 function 6 not configured
vr0 at pci0 dev 18 function 0: VIA VT6102 (Rhine II) 10/100 Ethernet
vr0: interrupting at irq 4
vr0: Ethernet address: 00:c0:9f:36:30:2c
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface
ukphy0: OUI 0x0002c6, model 0x0032, rev. 8
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0: cacheline 0x0 lattimer 0x10
cbb0: bhlc 0x21000
cbb0: secondary bus number uninitialized; try PCI_BUS_FIXUP
cbb0: interrupting at irq 5
cardslot0 at cbb0
pcmcia0 at cardslot0
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x1106 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
acpiacad0: AC adapter online.
wd0 at atabus0 drive 0: <IBM-DBCA-206480>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 6194 MB, 13424 cyl, 15 head, 63 sec, 512 bytes/sect x 12685680 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <Slimtype COMBO LSC-24082K, , JKQ1> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(viaide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
Section "Device"
Identifier "Card0"
Driver "via"
VendorName "Unknown Vendor"
BoardName "Unknown Board"
BusID "PCI:1:0:0"
EndSection
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
RgbPath "/usr/X11R7/lib/X11/rgb"
ModulePath "/usr/X11R7/lib/modules"
FontPath "/usr/X11R7/lib/X11/fonts/misc/"
FontPath "/usr/X11R7/lib/X11/fonts/TTF/"
FontPath "/usr/X11R7/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R7/lib/X11/fonts/Type1/"
FontPath "/usr/X11R7/lib/X11/fonts/CID/"
FontPath "/usr/X11R7/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R7/lib/X11/fonts/100dpi/"
EndSection
Section "Module"
Load "GLcore"
Load "cfb"
Load "cfb32"
Load "dbe"
Load "dri"
Load "extmod"
Load "glx"
Load "mfb"
Load "record"
Load "shadow"
Load "xtrap"
Load "freetype"
Load "type1"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "wsmouse"
Option "Device" "/dev/wsmouse"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
HorizSync 31.5 - 48.0
VertRefresh 59.0 - 75.0
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x768"
EndSubSection
EndSection
Home |
Main Index |
Thread Index |
Old Index