Re: Booting HP pavilion dv2000 laptop

To: current-users%NetBSD.org@localhost
Subject: Re: Booting HP pavilion dv2000 laptop
From: "John D. Baker" <jdbaker%mylinuxisp.com@localhost>
Date: Sun, 6 Nov 2016 18:39:31 -0600 (CST)
On Sun, 30 Oct 2016, John D. Baker wrote:

> Booting GENERIC with "-2c" to disable ACPI and drop into userconf
> permits disabling the "nouveau*" driver after which the process continues
> as above (hangs probing cd0 and wd0 until power button is pressed).

Booting with -12c to disable SMP and ACPI and disabling nouveau via
userconf, the machine does not hang when probing IDE/ATA devices and
completes multiuser boot without any intervention.

On Sun, 30 Oct 2016 06:47:48 +0000 (UTC),  mlelstv%serpens.de@localhost (Michael
van Elst) wrote:

> >vga0 at pci0 dev 5 function 0: NVIDIA product 0244 (rev. 0xa2)
>
> That's a GeForce Go 6150. Nouveau is "supposed" to support this
> hardware, but there have been lots of issues in the past (on Linux).

Interesting to note.  My brother is the one who installed Linux Mint
17.3 on this machine and told me that he couldn't get "nouveau" to work
either, resorting to the nVidia blob driver.


Below is dmesg.boot with "-12vxc" to get maximum verbosity and debug info:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 7.99.42 (GENERIC) #37: Sun Nov  6 01:40:29 CDT 2016
	sysop%yggdrasil.technoskunk.fur@localhost:/r0/build/current/obj/amd64/sys/arch/amd64/compile/GENERIC
total memory = 1982 MB
avail memory = 1904 MB
Prep module path=acpiverbose len=59520 pa=14eb000
Prep module path=pciverbose len=110136 pa=14fa000
Prep module path=usbverbose len=49696 pa=1515000
Prep module path=miiverbose len=15072 pa=1522000
Prep module path=nfs len=393128 pa=1526000
WARNING: module error: module `nfs' pushed by boot loader already exists
timecounter: Timecounters tick every 10.000 msec
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 26 flags 0 maxoplen 0
crypto: driver 0 registers alg 27 flags 0 maxoplen 0
crypto: driver 0 registers alg 29 flags 0 maxoplen 0
crypto: driver 0 registers alg 33 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 19 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 20 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 24 flags 0 maxoplen 0
crypto: driver 0 registers alg 25 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 21 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 28 flags 0 maxoplen 0
crypto: driver 0 registers alg 30 flags 0 maxoplen 0
crypto: driver 0 registers alg 31 flags 0 maxoplen 0
crypto: driver 0 registers alg 32 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
crypto: driver 0 registers alg 23 flags 0 maxoplen 0
crypto: driver 0 registers alg 22 flags 0 maxoplen 0
Kernelized RAIDframe activated
userconf: configure system autoconfiguration:
uc> disable nouveau
[340] nouveau* disabled
uc> exit
Continuing...
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.4 @ 0xdc010 (27 entries)
Hewlett-Packard HP Pavilion dv2000 (GA536UA#ABA) (F.34)
mainbus0 (root)
cpu0 at mainbus0
cpu0: 8 page colors
cpu0: AMD Turion(tm) 64 X2 , id 0x40f82
cpu0: PAT enabled
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
NVIDIA C51 Host Bridge (0x02f0) (RAM memory, revision 0xa2) at pci0 dev 0 function 0 not configured
NVIDIA C51 Memory Controller 0 (RAM memory, revision 0xa2) at pci0 dev 0 function 1 not configured
NVIDIA C51 Memory Controller 1 (RAM memory, revision 0xa2) at pci0 dev 0 function 2 not configured
NVIDIA C51 Memory Controller 5 (RAM memory, revision 0xa2) at pci0 dev 0 function 3 not configured
NVIDIA C51 Memory Controller 4 (RAM memory, revision 0xa2) at pci0 dev 0 function 4 not configured
Skipping broken PCI header on 0:0:5
Skipping broken PCI header on 0:0:5
NVIDIA C51 Host Bridge (0x02ff) (RAM memory, revision 0xa2) at pci0 dev 0 function 5 not configured
NVIDIA C51 Memory Controller 3 (RAM memory, revision 0xa2) at pci0 dev 0 function 6 not configured
NVIDIA C51 Memory Controller 2 (RAM memory, revision 0xa2) at pci0 dev 0 function 7 not configured
ppb0 at pci0 dev 2 function 0: NVIDIA C51 PCI Express Bridge (0x02fc) (rev. 0xa1)
ppb0: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
ppb0: disabling notification events
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
bwi0 at pci1 dev 0 function 0: Broadcom Wireless
bwi0: interrupting at irq 11
bwi0: BBP id 0x4311, BBP rev 0x2, BBP pkg 0
bwi0: MAC rev 13 is not supported
bwi0: no MAC was found
ppb1 at pci0 dev 3 function 0: NVIDIA C51 PCI Express Bridge (0x02fd) (rev. 0xa1)
ppb1: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
ppb1: disabling notification events
pci2 at ppb1 bus 3
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci0 dev 5 function 0: NVIDIA product 0244 (rev. 0xa2)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
NVIDIA nForce430 Host Bridge (RAM memory, revision 0xa2) at pci0 dev 9 function 0 not configured
pcib0 at pci0 dev 10 function 0: NVIDIA nForce430 PCI-ISA Bridge (rev. 0xa3)
nfsmbc0 at pci0 dev 10 function 1: NVIDIA nForce430 SMBus Controller (rev. 0xa3)
nfsmb0 at nfsmbc0 SMBus 1
iic0 at nfsmb0: I2C bus
nfsmb1 at nfsmbc0 SMBus 2
iic1 at nfsmb1: I2C bus
NVIDIA product 0271 (Co-processor processor, revision 0xa3) at pci0 dev 10 function 3 not configured
ohci0 at pci0 dev 11 function 0: NVIDIA nForce430 USB Controller (rev. 0xa3)
ohci0: interrupting at irq 11
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
usb0: WARNING: power management not supported
ehci0 at pci0 dev 11 function 1: NVIDIA nForce430 USB2 Controller (rev. 0xa3)
ehci0: interrupting at irq 7
ehci0: BIOS refuses to give up ownership, using force
ehci0: EHCI version 1.0
ehci0: companion controller, 8 ports each: ohci0
usb1 at ehci0: USB revision 2.0
usb1: WARNING: power management not supported
viaide0 at pci0 dev 13 function 0: NVIDIA nForce430 IDE Controller (rev. 0xf1)
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
viaide1 at pci0 dev 14 function 0: NVIDIA nForce430 Serial ATA Controller (rev. 0xf1)
viaide1: bus-master DMA support present
viaide1: primary channel wired to native-PCI mode
viaide1: using irq 5 for native-PCI interrupt
atabus2 at viaide1 channel 0
viaide1: secondary channel wired to native-PCI mode
atabus3 at viaide1 channel 1
ppb2 at pci0 dev 16 function 0: NVIDIA nForce430 PCI-PCI Bridge (rev. 0xa2)
pci3 at ppb2 bus 5
pci3: i/o space, memory space enabled
fwohci0 at pci3 dev 9 function 0: Ricoh 5C832 PCI-SD/MMC/MMC+/MS/xD/Firewire (rev. 0x00)
fwohci0: interrupting at irq 10
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 xx:xx:xx:xx:xx:xx:xx:xx
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
sdhc0 at pci3 dev 9 function 1: Ricoh 5C822 PCI-CardBus Bridge/MS/SD/MMC/SC (rev. 0x19)
sdhc0: interrupting at irq 10
sdhc0: SDHC 1.0, rev 2, SDMA, 33000 kHz, 3.3V, 512 byte blocks
sdmmc0 at sdhc0 slot 0
Ricoh 5C843 PCI-CardBus Bridge/SD/MMC/MMC+/MS/xD/Firewire (miscellaneous system, revision 0x01) at pci3 dev 9 function 2 not configured
Ricoh 5C592 PCI-CardBus Bridge/MS/SD/Firewire (miscellaneous system, revision 0x0a) at pci3 dev 9 function 3 not configured
Ricoh xD-Picture Card Controller (miscellaneous system, revision 0x05) at pci3 dev 9 function 4 not configured
hdaudio0 at pci0 dev 16 function 1: HD Audio Controller
hdaudio0: interrupting at irq 10
hdafg0 at hdaudio0 vendor 0x14F1 product 0x5045 nid 0x01: vendor 14f1 product 5045
hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack]
    nid=10 [pin: Speaker (Built-In)]
           nid=19 [audio output] [source: dac]
    nid=11 [pin: HP Out (Green Jack)]
           nid=19 [audio output] [source: dac]
hdafg0: DIG01 2ch: SPDIF Out [Jack]
    nid=13 [pin: SPDIF Out (Black Jack)]
           nid=18 [audio output] [source: dac]
hdafg0: ADC02 2ch: Mic In [Built-In]
    nid=14 [pin: Mic In (Built-In)]
hdafg0: 2ch/2ch 48000Hz 96000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
hdvsmfg at hdaudio0 vendor 0x14F1 product 0x5045 nid 0x02 not configured
nfe0 at pci0 dev 20 function 0: NVIDIA nForce430 Gigabit Ethernet Controller (rev. 0xa3)
nfe0: interrupting at irq 11
nfe0: Ethernet address xx:xx:xx:xx:xx:xx
ukphy0 at nfe0 phy 1: Marvell 88E1118 Gigabit PHY (OUI 0x000ac2, model 0x0022), rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pchb0 at pci0 dev 24 function 0: AMD K8 AMD64 HyperTransport Configuration (rev. 0x00)
pchb1 at pci0 dev 24 function 1: AMD K8 AMD64 Address Map Configuration (rev. 0x00)
pchb2 at pci0 dev 24 function 2: AMD K8 AMD64 DRAM Configuration (rev. 0x00)
amdnb_misc0 at pci0 dev 24 function 3: AMD NB Misc Configuration
amdtemp0 at amdnb_misc0: AMD CPU Temperature Sensors (K8: core rev BH-F2, socket S1)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pms0: Synaptics touchpad version 6.2
pms0: synaptics_probe: Capabilities 0xa013.
pms0: pms_synaptics_probe_extended: Extended Buttons: 0.
pms0: pms_synaptics_probe_extended: Extended Capabilities: 0x20 0x00 0x00.
pms0: pms_synaptics_probe_extended: Continued Capabilities 0x65 0x3b 0x61.
pms0: Palm detect, Two button click pad, Multi-finger
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
attimer0: attached to pcppi0
powernow0 at cpu0: failed to initialize (err 6)
powernow0: WARNING: power management not supported
Initializing SSP: 4bcb1766eb389ce2 eda7bbeef413ff73 ee9654798192e2a0 399c1642c2385426 db9af3b8a0c60302 e84d4779a76c0d91 9a6c4bcb1234dc a0d79104ba895b6f 
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
TSC not known invariant on this CPU
timecounter: Timecounter "TSC" frequency 1808327960 Hz quality -100
atapibus0 at atabus1: 2 targets
IPsec: Initialized Security Association Processing.
uhub0 at usb0: NVIDIA OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 8 ports with 8 removable, self powered
uhub1 at usb1: NVIDIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 8 ports with 8 removable, self powered
cd0 at atapibus0 drive 0: <HL-DT-ST DVDRAM GSA-T20L, KYC76KA5521, NC08> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(viaide0:1:0): using PIO mode 4, DMA mode 2 (using DMA)
viaide1 port 0: device present, speed: 1.5Gb/s
wd0 at atabus2 drive 0
wd0: <FUJITSU MHV2080BH>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide1:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
uvideo0 at uhub1 port 8 configuration 1 interface 0: Sonix Technology Co., Ltd. USB 2.0 Camera, rev 2.00/2.10, addr 2
video0 at uvideo0: Sonix Technology Co., Ltd. USB 2.0 Camera, rev 2.00/2.10, addr 2
crypto: assign driver 1, flags 2
crypto: driver 1 registers alg 1 flags 0 maxoplen 0
crypto: driver 1 registers alg 2 flags 0 maxoplen 0
crypto: driver 1 registers alg 3 flags 0 maxoplen 0
crypto: driver 1 registers alg 4 flags 0 maxoplen 0
crypto: driver 1 registers alg 5 flags 0 maxoplen 0
crypto: driver 1 registers alg 26 flags 0 maxoplen 0
crypto: driver 1 registers alg 27 flags 0 maxoplen 0
crypto: driver 1 registers alg 29 flags 0 maxoplen 0
crypto: driver 1 registers alg 33 flags 0 maxoplen 0
crypto: driver 1 registers alg 17 flags 0 maxoplen 0
crypto: driver 1 registers alg 6 flags 0 maxoplen 0
crypto: driver 1 registers alg 19 flags 0 maxoplen 0
crypto: driver 1 registers alg 7 flags 0 maxoplen 0
crypto: driver 1 registers alg 20 flags 0 maxoplen 0
crypto: driver 1 registers alg 15 flags 0 maxoplen 0
crypto: driver 1 registers alg 24 flags 0 maxoplen 0
crypto: driver 1 registers alg 25 flags 0 maxoplen 0
crypto: driver 1 registers alg 8 flags 0 maxoplen 0
crypto: driver 1 registers alg 21 flags 0 maxoplen 0
crypto: driver 1 registers alg 16 flags 0 maxoplen 0
crypto: driver 1 registers alg 9 flags 0 maxoplen 0
crypto: driver 1 registers alg 10 flags 0 maxoplen 0
crypto: driver 1 registers alg 13 flags 0 maxoplen 0
crypto: driver 1 registers alg 14 flags 0 maxoplen 0
crypto: driver 1 registers alg 28 flags 0 maxoplen 0
crypto: driver 1 registers alg 30 flags 0 maxoplen 0
crypto: driver 1 registers alg 31 flags 0 maxoplen 0
crypto: driver 1 registers alg 32 flags 0 maxoplen 0
crypto: driver 1 registers alg 11 flags 0 maxoplen 0
crypto: driver 1 registers alg 18 flags 0 maxoplen 0
crypto: driver 1 registers alg 23 flags 0 maxoplen 0
crypto: driver 1 registers alg 22 flags 0 maxoplen 0
pad: requested 1 units
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
Searching for RAID components...
WARNING: 2 errors while detecting hardware; check system log.
boot device: nfe0
root on nfe0
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: q.r.s.t
nfs_boot: my_name=dpe2850e
nfs_boot: my_domain=technoskunk.fur
nfs_boot: my_addr=a.b.c.d
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=l.m.n.o
root on q.r.s.t:/r0/diskless/dpe2850e
root file system type: nfs
kern.module.path=/stand/amd64/7.99.42/modules
wsdisplay0: screen 1 added (80x25, vt100 emulation)
Kernel RNG "kernel" long run test FAILURE: Run of 27 0s found
cprng kernel: failed statistical RNG test
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

-- 
|/"\ John D. Baker, KN5UKS               NetBSD     Darwin/MacOS X
|\ / jdbaker[snail]mylinuxisp[flyspeck]com    OpenBSD            FreeBSD
| X  No HTML/proprietary data in email.   BSD just sits there and works!
|/ \ GPGkeyID:  D703 4A7E 479F 63F8 D3F4  BD99 9572 8F23 E4AD 1645
References:
- Booting HP pavilion dv2000 laptop
  - From: John D. Baker
Prev by Date: Re: Automated report: NetBSD-current/i386 test failure
Next by Date: daily CVS update output
Previous by Thread: Re: Booting HP pavilion dv2000 laptop
Next by Thread: internal compiler error heimdal
Indexes:
Home | Main Index | Thread Index | Old Index