Re: ohci: WARNING: addr ... not found

[Izumi Tsutsui <tsutsui%ceres.dti.ne.jp@localhost>]

> On Tue, Mar 05, 2013 at 11:10:59PM +0900, Izumi Tsutsui wrote:
> > > Since upgrading from 5.1 to 6.0.1, I get a lot of new warnings I
> > > hadn't seen before:
> > > 
> > > Mar  2 10:23:33 nas /netbsd: ohci1: WARNING: addr 0x00001b80 not found
> >  :
> > > Any ideas what this means and why it's appearing now?
> > 
> > On powerpc?
> 
> No, amd64.

My Shuttle SA76 (AMD760G + SB710) works without problem,
so it would be device specific?

---
NetBSD 6.0.1 (GENERIC)
total memory = 3838 MB
avail memory = 3711 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Shuttle Inc. SA76 (V10)
mainbus0 (root)
ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 
0x0000000000000000/0x1 (20110623/tbfadt-586)
cpu0 at mainbus0 apid 0: AMD Athlon(tm) II X2 260 Processor, id 0x100f63
cpu1 at mainbus0 apid 1: AMD Athlon(tm) II X2 260 Processor, id 0x100f63
 :
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
 :
ohci0 at pci0 dev 18 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 16
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 18 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 16
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ehci0 at pci0 dev 18 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci0: interrupting at ioapic0 pin 17
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
ohci2 at pci0 dev 19 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2: OHCI version 1.0, legacy support
usb3 at ohci2: USB revision 1.0
ohci3 at pci0 dev 19 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci3: interrupting at ioapic0 pin 18
ohci3: OHCI version 1.0, legacy support
usb4 at ohci3: USB revision 1.0
ehci1 at pci0 dev 19 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci1: interrupting at ioapic0 pin 19
ehci1: dropped intr workaround enabled
ehci1: EHCI version 1.0
ehci1: companion controllers, 3 ports each: ohci2 ohci3
usb5 at ehci1: USB revision 2.0
 :
ohci4 at pci0 dev 20 function 5: vendor 0x1002 product 0x4399 (rev. 0x00)
ohci4: interrupting at ioapic0 pin 18
ohci4: OHCI version 1.0, legacy support
usb6 at ohci4: USB revision 1.0
 :
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
uhub2 at usb2: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
uhub3 at usb3: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 3 ports with 3 removable, self powered
uhub4 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 3 ports with 3 removable, self powered
 :
uhub7: at uhub4 port 2 (addr 2) disconnected
uhub7 at uhub4 port 2: Genesys Logic USB Hub, class 9/0, rev 1.01/0.12, addr 2
uhub7: 4 ports with 4 removable, self powered
umass0 at uhub7 port 2 configuration 1 interface 0
umass0: BUFFALO ClipDrive, rev 2.00/2.00, addr 3
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <BUFFALO, ClipDrive, 2.00> disk removable
sd0: fabricating a geometry
sd0: 250 MB, 250 cyl, 64 head, 32 sec, 512 bytes/sect x 512000 sectors
sd0: fabricating a geometry

---
Izumi Tsutsui