Problem with hdaudio...

[Paul Goyette <paul%whooppee.com@localhost>]

I replaced my azalia's with hdaudio, and with a 5.99.17 kernel (built 
from sources updated just a couple hours ago) I get the following trace 
during autoconfig (manually transposed, since I'm using a USB keyboard)


audio_calcwater + 0xb
audiosetinfo + 0x4d1
audio_set_defaults + 0xdd
audio_attach + 0x226
config_attach_loc + 0x16b
audio_attach_mi + 0x32
hdaudio_attach_fg + 0xce
hdaudio_attach + 0x4c9
hdaudio_pci_attach + 0x16d
config_attach_loc + 0x16b
pci_probe_device
...

Disabling hdaudio0 (via boot -c) lets me finish booting;  the resulting 
dmesg is attached.

-------------------------------------------------------------------------
|   Paul Goyette   | PGP DSS Key fingerprint: |  E-mail addresses:      |
| Customer Service | FA29 0E3B 35AF E8AE 6651 |  paul at whooppee.com   |
| Network Engineer | 0786 F758 55DE 53BA 7731 | pgoyette at juniper.net |
| Kernel Developer |                          | pgoyette at netbsd.org  |
-------------------------------------------------------------------------

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.17 (ZIPPY (ASUS M3A78-CM) 2009-09-12 20:02:41) #5: Sat Sep 12 
13:09:28 PDT 2009
        
paul%speedy.whooppee.com@localhost:/build/netbsd-local/obj/amd64/sys/arch/amd64/compile/ZIPPY
total memory = 6143 MB
avail memory = 5947 MB
timecounter: Timecounters tick every 10.000 msec
userconf: configure system autoconfiguration:
uc> disable hdaudio0
[ 79] hdaudio0 disabled
uc> disable hdaudio1
[ 80] hdaudio1 disabled
uc> disable hdaudo^H ^Hio2
uc> exiot^H ^H^H ^Ht
Continuing...
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
System manufacturer System Product Name (System Version)
mainbus0 (root)
cpu0 at mainbus0 apid 0: AMD 686-class, 3014MHz, id 0x100f42
cpu1 at mainbus0 apid 1: AMD 686-class, 3014MHz, id 0x100f42
cpu2 at mainbus0 apid 2: AMD 686-class, 3014MHz, id 0x100f42
cpu3 at mainbus0 apid 3: AMD 686-class, 3014MHz, id 0x100f42
ioapic0 at mainbus0 apid 4: pa 0xfec00000, version 21, 24 pins
acpi0 at mainbus0: Intel ACPICA 20090730
acpi0: X/RSDT: OemId <071508,XSDT1643,20080715>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 32-bit timer
attimer0 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi0 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
fdc0 at acpi0 (FDC, PNP0700): io 0x3f0-0x3f5,0x3f7 irq 6 drq 2
ACPI Warning for \_SB_.PCI0.SBRG.FDC_._FDE: Return type mismatch - found 
Package, expected Buffer (20090730/nspredef-1139)
fdc0: expected BUFFER, got 4
lpt0 at acpi0 (LPTE, PNP0400): io 0x378-0x37f irq 7
aiboost0 at acpi0 (ASOC, ATK0110-16843024)
aiboost0: ASUS AI Boost Hardware monitor
hpet0 at acpi0 (HPET, PNP0103): mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
com0 at acpi0 (UAR1, PNP0501-1): io 0x3f8-0x3ff irq 4
com0: ns16550a, working fifo
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
attimer0: attached to pcppi0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x1022 product 0x9600 (rev. 0x00)
ppb0 at pci0 dev 2 function 0: vendor 0x1022 product 0x9603 (rev. 0x00)
ppb0: unsupported PCI Express version
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci1 dev 0 function 0: vendor 0x1002 product 0x5b60 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
vendor 0x1002 product 0x5b70 (miscellaneous display) at pci1 dev 0 function 1 
not configured
ppb1 at pci0 dev 6 function 0: vendor 0x1022 product 0x9606 (rev. 0x00)
ppb1: unsupported PCI Express version
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci2 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet (rev. 
0x02)
re0: interrupting at ioapic0 pin 18
re0: Ethernet address 00:22:15:ba:7f:cc
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ixpide0 at pci0 dev 17 function 0: ATI Technologies IXP IDE Controller (rev. 
0x00)
ixpide0: bus-master DMA support present
ixpide0: primary channel configured to native-PCI mode
ixpide0: using ioapic0 pin 22 for native-PCI interrupt
atabus0 at ixpide0 channel 0
ixpide0: secondary channel configured to native-PCI mode
atabus1 at ixpide0 channel 1
ohci0 at pci0 dev 18 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 16
ohci0:  OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 18 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 16
ohci1:  OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ehci0 at pci0 dev 18 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci0: applying AMD SB600/SB700 USB freeze workaround
ehci0: interrupting at ioapic0 pin 17
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
ohci2 at pci0 dev 19 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2:  OHCI version 1.0, legacy support
usb3 at ohci2: USB revision 1.0
ohci3 at pci0 dev 19 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci3: interrupting at ioapic0 pin 18
ohci3:  OHCI version 1.0, legacy support
usb4 at ohci3: USB revision 1.0
ehci1 at pci0 dev 19 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci1: applying AMD SB600/SB700 USB freeze workaround
ehci1: interrupting at ioapic0 pin 19
ehci1: dropped intr workaround enabled
ehci1: EHCI version 1.0
ehci1: companion controllers, 3 ports each: ohci2 ohci3
usb5 at ehci1: USB revision 2.0
piixpm0 at pci0 dev 20 function 0
piixpm0: vendor 0x1002 product 0x4385 (rev. 0x3a)
piixpm0: interrupting at SMI, polling
iic0 at piixpm0: I2C bus
dbcool_chip_ident: addr 0x2e c_id 0x00 d_id 0x00 r_id 0x00: No match.
spdmem0 at iic0 addr 0x50
spdmem0: DDR2 SDRAM, no parity or ECC, 2GB, 800MHz (PC2-6400)
spdmem0: 14 rows, 10 cols, 2 ranks, 8 banks/chip, 2.50ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 5-5-5-18
spdmem0: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
spdmem1 at iic0 addr 0x51
spdmem1: DDR2 SDRAM, no parity or ECC, 2GB, 800MHz (PC2-6400)
spdmem1: 14 rows, 10 cols, 2 ranks, 8 banks/chip, 2.50ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 5-5-5-18
spdmem1: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
spdmem2 at iic0 addr 0x52
spdmem2: DDR2 SDRAM, no parity or ECC, 1GB, 800MHz (PC2-6400)
spdmem2: 14 rows, 10 cols, 2 ranks, 4 banks/chip, 2.50ns cycle time
spdmem2: tAA-tRCD-tRP-tRAS: 5-5-5-18
spdmem2: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
spdmem3 at iic0 addr 0x53
spdmem3: DDR2 SDRAM, no parity or ECC, 1GB, 800MHz (PC2-6400)
spdmem3: 14 rows, 10 cols, 2 ranks, 4 banks/chip, 2.50ns cycle time
spdmem3: tAA-tRCD-tRP-tRAS: 5-5-5-18
spdmem3: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
ixpide1 at pci0 dev 20 function 1: ATI Technologies IXP IDE Controller (rev. 
0x00)
ixpide1: bus-master DMA support present
ixpide1: primary channel configured to compatibility mode
ixpide1: primary channel interrupting at ioapic0 pin 14
atabus2 at ixpide1 channel 0
ixpide1: secondary channel configured to compatibility mode
ixpide1: secondary channel interrupting at ioapic0 pin 15
atabus3 at ixpide1 channel 1
vendor 0x1002 product 0x4383 (multimedia subclass 0x03) at pci0 dev 20 function 
2 not configured
pcib0 at pci0 dev 20 function 3: vendor 0x1002 product 0x439d (rev. 0x00)
ppb2 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x00)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled
tlp0 at pci3 dev 6 function 0: ADMtek AN985 Ethernet, pass 1.1
tlp0: interrupting at ioapic0 pin 20
tlp0: Ethernet address 00:22:6b:bb:d6:2f
ukphy0 at tlp0 phy 1: OUI 0x00e092, model 0x0001, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re1 at pci3 dev 7 function 0: RealTek 8169/8110 Gigabit Ethernet (rev. 0x10)
re1: interrupting at ioapic0 pin 21
re1: Ethernet address 00:1e:2a:3f:6c:29
re1: using 256 tx descriptors
rgephy1 at re1 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 0
rgephy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ohci4 at pci0 dev 20 function 5: vendor 0x1002 product 0x4399 (rev. 0x00)
ohci4: interrupting at ioapic0 pin 18
ohci4:  OHCI version 1.0, legacy support
usb6 at ohci4: USB revision 1.0
pchb1 at pci0 dev 24 function 0: vendor 0x1022 product 0x1200 (rev. 0x00)
pchb2 at pci0 dev 24 function 1: vendor 0x1022 product 0x1201 (rev. 0x00)
pchb3 at pci0 dev 24 function 2: vendor 0x1022 product 0x1202 (rev. 0x00)
amdtemp0 at pci0 dev 24 function 3: AMD CPU Temperature Sensors (Family10h / 
Family11h)
pchb4 at pci0 dev 24 function 4: vendor 0x1022 product 0x1204 (rev. 0x00)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
itesio0 at isa0 port 0x2e-0x2f: iTE IT8712F Super I/O (rev 8)
itesio0: Hardware Monitor registers at 0x290
itesio0: Watchdog Timer present
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 3014263130 Hz quality 3000
fd0 at fdc0 drive 0: density unknown
fd1 at fdc0 drive 1: density unknown
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
uhub2 at usb2: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
uhub3 at usb3: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 3 ports with 3 removable, self powered
uhub4 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 3 ports with 3 removable, self powered
uhub5 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 6 ports with 6 removable, self powered
uhub6 at usb6: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
ehci0: handing over low speed device on port 3 to ohci0
uhidev0 at uhub0 port 3 configuration 1 interface 0
uhidev0: Justcom Technology USB KVM Switch, rev 1.10/1.00, addr 2, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub0 port 3 configuration 1 interface 1
uhidev1: Justcom Technology USB KVM Switch, rev 1.10/1.00, addr 2, iclass 3/1
ums0 at uhidev1: 5 buttons and Z dir.
wsmouse0 at ums0 mux 0
wd0 at atabus0 drive 0: <ST380815AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ixpide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
pad0: outputs: 44100Hz, 16-bit, stereo
audio2 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
Accounting started