I have a Dell Optiplex that boots a NetBSD/amd64 kernel built from
5.0_RC3 sources with azalia* disabled just fine. Booting a NetBSD/xen
kernel built from the same sources (also with azalia* disabled) hangs
the machine. The last message on the console is
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <TSSTcorp CD-RW/DVD-ROM TS-H493A, , D200> cdrom
removable
If I disable ehci NetBSD/xen boots.
Here is the dmesg of the NetBSD/amd64 kernel:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 5.99.8 (NETPLEX) #0: Fri Mar 27 16:15:07 AST 2009
root@:/usr/obj/sys/arch/amd64/compile/NETPLEX
total memory = 2037 MB
avail memory = 1959 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Dell Inc. OptiPlex 745
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2394MHz, id 0x6f6
cpu1 at mainbus0 apid 1: Intel 686-class, 2394MHz, id 0x6f6
ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <DELL , B8K ,00000014>, AslId <ASL ,00000061>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpibut0 at acpi0 (VBTN, PNP0C0C): ACPI Power Button
pcppi1 at acpi0 (SPK, PNP0800): io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x5f irq 0
PRT (PNP0401) at acpi0 not configured
COMA (PNP0501) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103): mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x2990 (rev. 0x02)
agp0 at pchb0: detected 7676k stolen memory
agp0: aperture at 0xc0000000, size 0x20000000
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x2991 (rev. 0x02)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci0 dev 2 function 0: vendor 0x8086 product 0x2992 (rev. 0x02)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
vendor 0x8086 product 0x2993 (miscellaneous display, revision 0x02) at pci0 dev
2 function 1 not configured
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x2834 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x2835 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 17
usb1 at uhci1: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x283a (rev. 0x02)
ehci0: interrupting at ioapic0 pin 22
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1
usb2 at ehci0: USB revision 2.0
vendor 0x8086 product 0x284b (multimedia subclass 0x03, revision 0x02) at pci0
dev 27 function 0 not configured
ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x283f (rev. 0x02)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 28 function 4: vendor 0x8086 product 0x2847 (rev. 0x02)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci3 dev 0 function 0: Broadcom BCM5754 Gigabit Ethernet
bge0: interrupting at ioapic0 pin 16
bge0: ASIC BCM5754/5787 A2 (0xb002), Ethernet address 00:1a:a0:b4:5d:43
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5754/5787 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
uhci2 at pci0 dev 29 function 0: vendor 0x8086 product 0x2830 (rev. 0x02)
uhci2: interrupting at ioapic0 pin 23
usb3 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 1: vendor 0x8086 product 0x2831 (rev. 0x02)
uhci3: interrupting at ioapic0 pin 17
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 2: vendor 0x8086 product 0x2832 (rev. 0x02)
uhci4: interrupting at ioapic0 pin 18
usb5 at uhci4: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x2836 (rev. 0x02)
ehci1: interrupting at ioapic0 pin 23
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci2 uhci3 uhci4
usb6 at ehci1: USB revision 2.0
ppb3 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xf2)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x2810 (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO timer reboot disabled by hardware; hope SMBIOS properly handles
it.
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 2
piixide0: Intel 82801H Serial ATA Controller (ICH8) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to native-PCI mode
piixide0: using ioapic0 pin 20 for native-PCI interrupt
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to native-PCI mode
atabus1 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x283e (rev. 0x02)
ichsmb0: interrupting at ioapic0 pin 20
iic0 at ichsmb0: I2C bus
piixide1 at pci0 dev 31 function 5
piixide1: Intel 82801H Serial ATA Controller (ICH8) (rev. 0x02)
piixide1: bus-master DMA support present
piixide1: primary channel wired to native-PCI mode
piixide1: using ioapic0 pin 20 for native-PCI interrupt
atabus2 at piixide1 channel 0
piixide1: secondary channel wired to native-PCI mode
atabus3 at piixide1 channel 1
isa0 at ichlpcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 2394139680 Hz quality 3000
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 6 ports with 6 removable, self powered
uhub7 at uhub6 port 4: vendor 0x0424 product 0x2504, class 9/0, rev 2.00/0.01,
addr 2
uhub7: multiple transaction translators
uhub7: 4 ports with 4 removable, self powered
uhci1: host controller halted
ugen0 at uhub4 port 1
ugen0: American Power Conversion Back-UPS CS 500 FW:806.q8.D USB FW:q8, rev
1.10/0.06, addr 2
wd0 at atabus0 drive 0: <WDC WD800JD-75MSA3>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 76293 MB, 155009 cyl, 16 head, 63 sec, 512 bytes/sect x 156250000 sectors
uhidev0 at uhub7 port 4 configuration 1 interface 0
uhidev0: Dell Dell USB Mouse, rev 2.00/1.10, addr 3, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
uhidev1 at uhub5 port 2 configuration 1 interface 0
uhidev1: Dell Dell USB Keyboard, rev 1.10/3.01, addr 2, iclass 3/1
ukbd0 at uhidev1
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <TSSTcorp CD-RW/DVD-ROM TS-H493A, , D200> cdrom
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
uhci0: host controller halted
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
MarkoAttachment:
pgp4Ygf6mXRNs.pgp
Description: PGP signature