Re: VIA C3

[Andrius V <vezhlys%gmail.com@localhost>]

Hi, Andy,

These VIA CPUs have their own AES and RNG implementation called
padlock. As far as I remember from testing my VT-310DP board few years
back padlock support was disabled by default in NetBSD kernel. You
need to uncomment "#padlock0 at cpu0 # VIA PadLock" line in GENERIC
and recompile the kernel.

On Thu, Jun 16, 2016 at 1:04 AM, Andy Ball <ball%grex.org@localhost> wrote:
> Hello Thor,
>
>     Here's the dmesg output from a very similar kernel that
> includes uhci and ehci for USB 2.0 support.  I will be away
> from this machine for about a week but will happily run some
> tests for you when I return.
>
> -Andy Ball
>
>
> Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
>     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
>     The NetBSD Foundation, Inc.  All rights reserved.
> Copyright (c) 1982, 1986, 1989, 1991, 1993
>     The Regents of the University of California.  All rights reserved.
>
> NetBSD 7.99.30 (NEHEMIAH-2.01) #3: Wed Jun 15 15:43:03 GMT 2016
>         root@nehemiah:/usr/src/sys/arch/i386/compile/NEHEMIAH
> total memory = 991 MB
> avail memory = 969 MB
> timecounter: Timecounters tick every 10.000 msec
> Kernelized RAIDframe activated
> timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
> VIA Technologies, Inc. VT8623-8235 ( )
> mainbus0 (root)
> ACPI: RSDP 0x00000000000F6620 000014 (v00 VT9174)
> ACPI: RSDT 0x000000003DFF3000 000028 (v01 VT9174 AWRDACPI 42302E31 AWRD 00000000)
> ACPI: FACP 0x000000003DFF3040 000074 (v01 VT9174 AWRDACPI 42302E31 AWRD 00000000)
> ACPI: DSDT 0x000000003DFF30C0 002FDD (v01 VT9174 AWRDACPI 00001000 MSFT 0100000C)
> ACPI: FACS 0x000000003DFF0000 000040
> ACPI: 1 ACPI AML tables successfully acquired and loaded
>
> cpu0 at mainbus0
> cpu0: VIA Nehemiah, id 0x691
> acpi0 at mainbus0: Intel ACPICA 20160422
> acpi0: X/RSDT: OemId <VT9174,AWRDACPI,42302e31>, AslId <AWRD,00000000>
> LNKB: ACPI: Found matching pin for 0.13.INTA at func 0: 12
> LNKA: ACPI: Found matching pin for 0.16.INTA at func 0: 11
> LNKB: ACPI: Found matching pin for 0.16.INTB at func 1: 12
> LNKC: ACPI: Found matching pin for 0.16.INTC at func 2: 10
> LNKD: ACPI: Found matching pin for 0.16.INTD at func 3: 5
> LNKA: ACPI: Found matching pin for 0.17.INTA at func 1: 255
> LNKC: ACPI: Found matching pin for 0.17.INTC at func 5: 10
> LNKA: ACPI: Found matching pin for 0.18.INTA at func 0: 11
> acpi0: SCI interrupting at int 9
> timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
> acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
> MEM (PNP0C01) at acpi0 not configured
> PMIO (PNP0C02) at acpi0 not configured
> SYSR (PNP0C02) at acpi0 not configured
> attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
> pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
> midi0 at pcppi1: PC speaker
> sysbeep0 at pcppi1
> COPR (PNP0C04) at acpi0 not configured
> FDC0 (PNP0700) at acpi0 not configured
> UAR1 (PNP0501) at acpi0 not configured
> UAR2 (PNP0501) at acpi0 not configured
> LPT1 (PNP0400) at acpi0 not configured
> pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
> apm0 at acpi0: Power Management spec V1.2
> attimer1: attached to pcppi1
> pckbd0 at pckbc1 (kbd slot)
> pckbc1: using irq 1 for kbd slot
> wskbd0 at pckbd0: console keyboard
> pci0 at mainbus0 bus 0: configuration mode 1
> pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
> pchb0 at pci0 dev 0 function 0: vendor 1106 product 3123 (rev. 0x00)
> agp0 at pchb0: aperture at 0xd0000000, size 0x8000000
> ppb0 at pci0 dev 1 function 0: vendor 1106 product b091 (rev. 0x00)
> pci1 at ppb0 bus 1
> pci1: i/o space, memory space enabled
> vga0 at pci1 dev 0 function 0: vendor 1106 product 3122 (rev. 0x03)
> wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
> wsmux1: connecting to wsdisplay0
> viadrmums0 at vga0drm: Supports vblank timestamp caching Rev 2 (21.10.2013).
> drm: No driver support for vblank timestamp query.
> fwohci0 at pci0 dev 13 function 0: vendor 1106 product 3044 (rev. 0x80)
> fwohci0: interrupting at irq 12
> fwohci0: OHCI version 1.0 (ROM=1)
> fwohci0: No. of Isochronous channels is 4.
> fwohci0: EUI64 00:40:63:00:00:03:b9:aa
> fwohci0: Phy 1394a available S400, 2 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> ieee1394if0 at fwohci0: IEEE1394 bus
> fwip at ieee1394if0 not configured
> fwohci0: Initiate bus reset
> uhci0 at pci0 dev 16 function 0: vendor 1106 product 3038 (rev. 0x80)
> uhci0: interrupting at irq 11
> usb0 at uhci0: USB revision 1.0
> uhci1 at pci0 dev 16 function 1: vendor 1106 product 3038 (rev. 0x80)
> uhci1: interrupting at irq 12
> usb1 at uhci1: USB revision 1.0
> uhci2 at pci0 dev 16 function 2: vendor 1106 product 3038 (rev. 0x80)
> uhci2: interrupting at irq 10
> usb2 at uhci2: USB revision 1.0
> ehci0 at pci0 dev 16 function 3: vendor 1106 product 3104 (rev. 0x82)
> ehci0: interrupting at irq 5
> ehci0: dropped intr workaround enabled
> ehci0: EHCI version 1.0
> ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
> usb3 at ehci0: USB revision 2.0
> viapcib0 at pci0 dev 17 function 0: vendor 1106 product 3177 (rev. 0x00)
> viapcib0: SMBus found at 0x500 (revision 0x0)
> iic0 at viapcib0: I2C bus
> viaide0 at pci0 dev 17 function 1
> viaide0: VIA Technologies VT8235 ATA133 controller
> viaide0: bus-master DMA support present
> viaide0: primary channel configured to compatibility mode
> viaide0: primary channel interrupting at irq 14
> atabus0 at viaide0 channel 0
> viaide0: secondary channel configured to compatibility mode
> viaide0: secondary channel interrupting at irq 15
> atabus1 at viaide0 channel 1
> auvia0 at pci0 dev 17 function 5: VIA Technologies VT8235 AC'97 Audio (rev 0x50)
> auvia0: interrupting at irq 10
> auvia0: ac97: VIA Technologies VT1616i codec; headphone, 18 bit DAC, 18 bit ADC, KS Waves 3D
> auvia0: ac97: ext id 0x1c5<LDAC,SDAC,CDAC,SPDIF,VRA>
> audio0 at auvia0: full duplex, playback, capture, mmap, independent
> vr0 at pci0 dev 18 function 0: vendor 1106 product 3065 (rev. 0x74)
> vr0: interrupting at irq 11
> vr0: Ethernet address: 00:40:63:cc:22:37
> ukphy0 at vr0 phy 1: OUI 0x0002c6, model 0x0032, rev. 5
> ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> isa0 at viapcib0
> lpt0 at isa0 port 0x378-0x37b irq 7
> com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
> com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
> acpicpu0 at cpu0: ACPI CPU
> acpicpu0: C1: HLT, lat   0 us, pow     0 mW
> acpicpu0: C2: I/O, lat  90 us, pow     0 mW
> acpicpu0: C3: I/O, lat 900 us, pow     0 mW
> acpicpu0: T0: I/O, lat   1 us, pow     0 mW, 100 %
> acpicpu0: T1: I/O, lat   1 us, pow     0 mW,  50 %
> fwohci0: BUS reset
> fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
> ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
> ieee1394if0: bus manager 0
> timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
> uhub0 at usb0: vendor 1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhub1 at usb1: vendor 1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> uhub2 at usb2: vendor 1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub2: 2 ports with 2 removable, self powered
> uhub3 at usb3: vendor 1106 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub3: 6 ports with 6 removable, self powered
> wd0 at atabus0 drive 0
> wd0: <ST340014A>
> wd0: drive supports 16-sector PIO transfers, LBA48 addressing
> wd0: 38146 MB, 77504 cyl, 16 head, 63 sec, 512 bytes/sect x 78125000 sectors
> wd0: 32-bit data port
> wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
> wd1 at atabus0 drive 1
> wd1: <Maxtor 32049H2>
> wd1: drive supports 16-sector PIO transfers, LBA addressing
> wd1: 19073 MB, 38752 cyl, 16 head, 63 sec, 512 bytes/sect x 39062500 sectors
> wd1: 32-bit data port
> wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
> wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
> wd1(viaide0:0:1): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
> boot device: wd0
> root on wd0a dumps on wd0b
> root file system type: ffs
> kern.module.path=/stand/i386/7.99.30/modules
> wsdisplay0: screen 1 added (80x25, vt100 emulation)
> wsdisplay0: screen 2 added (80x25, vt100 emulation)
> wsdisplay0: screen 3 added (80x25, vt100 emulation)
> wsdisplay0: screen 4 added (80x25, vt100 emulation)