Re: 6.0_BETA boot doesn't complete (same here except with HEAD)

[Blair Sadewitz <blair.sadewitz%gmail.com@localhost>]

I am having the same problem with this board using boot.iso from 201205251930Z.

http://www.intel.com/content/www/us/en/motherboards/desktop-motherboards/desktop-board-dh55pj.html

If I boot with AHCI enabled, I have this problem.  If I disable that
in the BIOS, the boot is successful.  I, too, could not use my
keyboard after the panic.  The message buffer from the successful boot
is appended to this message.

I just filed a PR under port-i386.

Thanks for any insights.

Regards,

--Blair

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.99.7 (GENERIC) #0: Sun May 20 07:09:57 UTC 2012
        
builds%b6.netbsd.org@localhost:/home/builds/ab/HEAD/i386/201205192330Z-obj/home/builds/ab/HEAD/src/sys/arch/i386/compile/GENERIC
total memory = 3253 MB
avail memory = 3186 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
                                                                    (
                               )
mainbus0 (root)
ACPI Warning: 32/64X FACS address mismatch in FADT -
0xCB61BF40/0x00000000CB61BE40, using 32 (20110623/tbfadt-517)
cpu0 at mainbus0 apid 0timecounter: Timecounter "lapic" frequency
133090992 Hz quality -100
: Intel(R) Core(TM) i3 CPU         540  @ 3.07GHz, id 0x20652
cpu1 at mainbus0 apid 1: Intel(R) Core(TM) i3 CPU         540  @
3.07GHz, id 0x20652
cpu2 at mainbus0 apid 4: Intel(R) Core(TM) i3 CPU         540  @
3.07GHz, id 0x20652
cpu3 at mainbus0 apid 5: Intel(R) Core(TM) i3 CPU         540  @
3.07GHz, id 0x20652
ioapic0 at mainbus0 apid 0: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <INTEL ,DH55PJ  ,01072009>, AslId <MSFT,00010013>
ACPI Warning: Incorrect checksum in table [SSDT] - 0x3F, should be
0x1F (20110623/tbutils-282)
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
MCH (PNP0C01) at acpi0 not configured
SIO1 (PNP0C02) at acpi0 not configured
UAR1 (PNP0501) at acpi0 not configured
LPTE (PNP0401) at acpi0 not configured
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
RMSC (PNP0C02) at acpi0 not configured
npx1 at acpi0 (COPR, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
PCH (PNP0C01) at acpi0 not configured
acpivga0 at acpi0 (GFX0): ACPI Display Adapter
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
RMEM (PNP0C01) at acpi0 not configured
OMSC (PNP0C02) at acpi0 not configured
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x0040 (rev. 0x02)
agp0 at pchb0: detected 32764k stolen memory
agp0: aperture at 0xd0000000, size 0x10000000
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x0042 (rev. 0x02)
vga1: WARNING: ignoring 64-bit BAR @ 0x10
vga1: WARNING: ignoring 64-bit BAR @ 0x18
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
vendor 0x8086 product 0x3b64 (miscellaneous communications, revision
0x06) at pci0 dev 22 function 0 not configured
pciide0 at pci0 dev 22 function 2: vendor 0x8086 product 0x3b66 (rev. 0x06)
pciide0: bus-master DMA support present, but unused (no driver support)
pciide0: primary channel wired to native-PCI mode
pciide0: using ioapic0 pin 18 for native-PCI interrupt
atabus0 at pciide0 channel 0
pciide0: secondary channel wired to native-PCI mode
atabus1 at pciide0 channel 1
vendor 0x8086 product 0x3b67 (serial communications, interface 0x02,
revision 0x06) at pci0 dev 22 function 3 not configured
wm0 at pci0 dev 25 function 0: PCH LAN (82578DC) Controller (rev. 0x06)
wm0: interrupting at ioapic0 pin 20
wm0: PCI-Express bus
wm0: FLASH
wm0: Ethernet address 70:71:bc:43:85:82
atphy0 at wm0 phy 2: Atheros AR8021 10/100/1000 PHY, rev. 2
atphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto
ehci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x3b3c (rev. 0x06)
ehci0: interrupting at ioapic0 pin 16
ehci0: EHCI version 1.0
ehci0: wrong number of companions (1 != 0)
usb0 at ehci0: USB revision 2.0
hdaudio0 at pci0 dev 27 function 0: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 22
hdafg0 at hdaudio0: Realtek ALC888
hdafg0: DAC00 2ch: Speaker [Jack]
hdafg0: DAC01 2ch: Speaker [Built-In]
hdafg0: DAC02 2ch: HP Out [Jack]
hdafg0: DIG03 2ch: SPDIF Out [Jack]
hdafg0: ADC04 2ch: Line In [Jack], Mic In [Jack]
hdafg0: ADC05 2ch: Mic In [Jack]
hdafg0: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, independent
hdafg1 at hdaudio0: Intel G45 HDMI
hdafg1: DP00 8ch: Digital Out [Jack]
hdafg1: 8ch/0ch 48000Hz PCM16*
ehci1 at pci0 dev 29 function 0: vendor 0x8086 product 0x3b34 (rev. 0x06)
ehci1: interrupting at ioapic0 pin 23
ehci1: EHCI version 1.0
ehci1: wrong number of companions (1 != 0)
usb1 at ehci1: USB revision 2.0
ppb0 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xa6)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
pcib0 at pci0 dev 31 function 0: vendor 0x8086 product 0x3b06 (rev. 0x06)
piixide0 at pci0 dev 31 function 2: Intel 3400 Serial ATA Controller (rev. 0x06)
piixide0: bus-master DMA support present
piixide0: primary channel configured to native-PCI mode
piixide0: using ioapic0 pin 19 for native-PCI interrupt
atabus2 at piixide0 channel 0
piixide0: secondary channel configured to native-PCI mode
atabus3 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x3b30 (rev. 0x06)
ichsmb0: interrupting at ioapic0 pin 18
iic0 at ichsmb0: I2C bus
piixide1 at pci0 dev 31 function 5: Intel 3400 Serial ATA Controller (rev. 0x06)
piixide1: bus-master DMA support present
piixide1: primary channel wired to native-PCI mode
piixide1: using ioapic0 pin 19 for native-PCI interrupt
atabus4 at piixide1 channel 0
piixide1: secondary channel wired to native-PCI mode
atabus5 at piixide1 channel 1
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat   3 us, pow  1000 mW
acpicpu0: C2: FFH, lat 205 us, pow   500 mW
acpicpu0: C3: FFH, lat 245 us, pow   350 mW, bus master check
acpicpu0: P0: FFH, lat  10 us, pow  9125 mW, 3059 MHz
acpicpu0: P1: FFH, lat  10 us, pow  8250 mW, 2926 MHz
acpicpu0: P2: FFH, lat  10 us, pow  7500 mW, 2793 MHz
acpicpu0: P3: FFH, lat  10 us, pow  6750 mW, 2660 MHz
acpicpu0: P4: FFH, lat  10 us, pow  6125 mW, 2527 MHz
acpicpu0: P5: FFH, lat  10 us, pow  5625 mW, 2394 MHz
acpicpu0: P6: FFH, lat  10 us, pow  5125 mW, 2261 MHz
acpicpu0: P7: FFH, lat  10 us, pow  4625 mW, 2128 MHz
acpicpu0: P8: FFH, lat  10 us, pow  4250 mW, 1995 MHz
acpicpu0: P9: FFH, lat  10 us, pow  2875 mW, 1197 MHz
acpicpu0: T0: FFH, lat   1 us, pow  1000 mW, 100 %
acpicpu0: T1: FFH, lat   1 us, pow   875 mW,  88 %
acpicpu0: T2: FFH, lat   1 us, pow   750 mW,  75 %
acpicpu0: T3: FFH, lat   1 us, pow   625 mW,  63 %
acpicpu0: T4: FFH, lat   1 us, pow   500 mW,  50 %
acpicpu0: T5: FFH, lat   1 us, pow   375 mW,  38 %
acpicpu0: T6: FFH, lat   1 us, pow   250 mW,  25 %
acpicpu0: T7: FFH, lat   1 us, pow   125 mW,  13 %
coretemp0 at cpu0: thermal sensor, 1 C resolution
acpicpu1 at cpu1: ACPI CPU
acpicpu2 at cpu2: ACPI CPU
coretemp1 at cpu2: thermal sensor, 1 C resolution
acpicpu3 at cpu3: ACPI CPU
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 3059220680 Hz quality -100
uhub0 at usb0: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
uhub2 at uhub1 port 1: vendor 0x8087 product 0x0020, class 9/0, rev
2.00/0.00, addr 2
uhub2: single transaction translator
uhub3 at uhub0 port 1: vendor 0x8087 product 0x0020, class 9/0, rev
2.00/0.00, addr 2
uhub3: single transaction translator
uhub3: 6 ports with 6 removable, self powered
uhub2: 8 ports with 8 removable, self powered
wd0 at atabus2 drive 0
wd0: <WDC WD5001AALS-00J7B0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
uaudio0 at uhub3 port 2 configuration 1 interface 0
uaudio0: vendor 0x046d HD Webcam C525, rev 2.00/0.10, addr 3
uaudio0: audio rev 1.00
uaudio0: 2 mixer controls
audio1 at uaudio0: full duplex, playback, capture, independent
uvideo0 at uhub3 port 2 configuration 1 interface 2: vendor 0x046d HD
Webcam C525, rev 2.00/0.10, addr 3
uhidev0 at uhub3 port 3 configuration 1 interface 0
uhidev0: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM), rev
1.10/3.00, addr 4, iclass 3/1
ums0 at uhidev0: 5 buttons and Z dir
wsmouse0 at ums0 mux 0
ulpt0 at uhub3 port 6 configuration 1 interface 0
ulpt0: KONICA MINOLTA PP1350W, rev 1.10/1.00, addr 5, iclass 7/1
ulpt0: using bi-directional mode
atapibus0 at atabus3: 2 targets
cd0 at atapibus0 drive 0: <Optiarc DVD RW AD-7260S, , 1.01> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 26 flags 0 maxoplen 0
crypto: driver 0 registers alg 27 flags 0 maxoplen 0
crypto: driver 0 registers alg 29 flags 0 maxoplen 0
crypto: driver 0 registers alg 33 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 19 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 20 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 24 flags 0 maxoplen 0
crypto: driver 0 registers alg 25 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 21 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 28 flags 0 maxoplen 0
crypto: driver 0 registers alg 30 flags 0 maxoplen 0
crypto: driver 0 registers alg 31 flags 0 maxoplen 0
crypto: driver 0 registers alg 32 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
crypto: driver 0 registers alg 23 flags 0 maxoplen 0
crypto: driver 0 registers alg 22 flags 0 maxoplen 0
Kernelized RAIDframe activated
boot device: cd0
root on cd0a dumps on cd0b
root file system type: cd9660
warning: no /dev/console