ixpide0:0:0: lost interrupt hang

To: port-i386%netbsd.org@localhost
Subject: ixpide0:0:0: lost interrupt hang
From: David Brownlee <abs%absd.org@localhost>
Date: Fri, 3 Oct 2008 20:02:32 +0100 (BST)

        I'm trying to install on a Jetway JNC81-LF AM2+ AMD780G MiniITX
        motherboard (Very nice little board under Windows)

        http://linitx.com/viewproduct.php?prodid=12207

        Under heavy disk load NetBSD hangs with a variant of the message
        below (block numbers change)

ixpide0:0:0: lost inteerupt
        type: ata tc_bcount: 2048 tc_skip: 0
ixpide:0:0:0: bus-master DMA error: missing interrupt, status=0x21
wd0a: DMA error writing fsbn 25741004 of  25741004-25741007 (wd0 bn 87173564; 
cn 86481 tn 11 sn 23), retrying

[..then the following repeated five times..]

ixpide0 channel 0: reset failed for drive 0
ixpide0:0:0: wait timed out
wd0a: device timeout writing fsbn 25741004 of  25741004-25741007 (wd0 bn 
87173564; cn 86481 tn 11 sn 23), retrying

[..then again six times for 25741008, 25741016..]

        Anyone have any thoughts on how to approach this?

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.72 (_PF_) #0: Wed Oct  1 20:35:48 BST 2008
        
abs%iris.absd.org@localhost:/files/netbsd/revivesa/sys/arch/i386/compile/_PF_
total memory = 1791 MB
avail memory = 1749 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Unknow Unknow (Unknow)
mainbus0 (root)
cpu0 at mainbus0 apid 0: AMD 686-class, 2400MHz, id 0x50ff3
cpu0: AMD PowerNow! Technology 2400 MHz
cpu0: available frequencies (Mhz): 1000 1800 2000 2200 2400
ioapic0 at mainbus0 apid 4: pa 0xfec00000, version 21, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <RS780 ,AWRDACPI,42302e31>, AslId <AWRD,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 32-bit timer
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x43
hpet0 at acpi0 (HPET, PNP0103)
hpet0: mem 0xfed00000-0xfed003ff irq 0,8
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
pckbc1 at acpi0 (PS2K, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
FAN (PNP0C0B) at acpi0 not configured
acpitz0 at acpi0 (THRM): active cooling level 0: 68.0C critical 70.0C passive 
48.0C
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1022 product 0x9600 (rev. 0x00)
ppb0 at pci0 dev 1 function 0: vendor 0x1022 product 0x9602 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 5 function 0: vendor 0x1002 product 0x9610 (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
azalia0 at pci1 dev 5 function 1: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 19
azalia0: host: 0x1002/0x960f (rev. 0), HDA rev. 1.0
ppb1 at pci0 dev 4 function 0: vendor 0x1022 product 0x9604 (rev. 0x00)
ppb1: unsupported PCI Express version
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci2 dev 0 function 0: RealTek 8168B/8111B PCIe Gigabit Ethernet (rev. 
0x02)
re0: interrupting at ioapic0 pin 16
re0: Unknown revision (0x3c400000)
re0: Ethernet address 00:30:18:a4:60:5f
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb2 at pci0 dev 5 function 0: vendor 0x1022 product 0x9605 (rev. 0x00)
ppb2: unsupported PCI Express version
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
re1 at pci3 dev 0 function 0: RealTek 8168B/8111B PCIe Gigabit Ethernet (rev. 
0x02)
re1: interrupting at ioapic0 pin 17
re1: Unknown revision (0x3c400000)
re1: Ethernet address 00:30:18:a4:60:60
re1: using 256 tx descriptors
rgephy1 at re1 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ixpide0 at pci0 dev 17 function 0
ixpide0: ATI Technologies IXP IDE Controller (rev. 0x00)
ixpide0: bus-master DMA support present
ixpide0: primary channel configured to native-PCI mode
ixpide0: using ioapic0 pin 22 for native-PCI interrupt
atabus0 at ixpide0 channel 0
ixpide0: secondary channel configured to native-PCI mode
atabus1 at ixpide0 channel 1
ohci0 at pci0 dev 18 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 16
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 18 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 16
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ehci0 at pci0 dev 18 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci0: interrupting at ioapic0 pin 17
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
ohci2 at pci0 dev 19 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2: OHCI version 1.0, legacy support
usb3 at ohci2: USB revision 1.0
ohci3 at pci0 dev 19 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci3: interrupting at ioapic0 pin 18
ohci3: OHCI version 1.0, legacy support
usb4 at ohci3: USB revision 1.0
ehci1 at pci0 dev 19 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci1: interrupting at ioapic0 pin 19
ehci1: dropped intr workaround enabled
ehci1: EHCI version 1.0
ehci1: companion controllers, 3 ports each: ohci2 ohci3
usb5 at ehci1: USB revision 2.0
piixpm0 at pci0 dev 20 function 0
piixpm0: vendor 0x1002 product 0x4385 (rev. 0x3a)
piixpm0: interrupting at SMI
iic0 at piixpm0: I2C bus
ixpide1 at pci0 dev 20 function 1
ixpide1: ATI Technologies IXP IDE Controller (rev. 0x00)
ixpide1: bus-master DMA support present
ixpide1: primary channel configured to compatibility mode
ixpide1: primary channel interrupting at ioapic0 pin 14
atabus2 at ixpide1 channel 0
ixpide1: secondary channel configured to compatibility mode
ixpide1: secondary channel interrupting at ioapic0 pin 15
atabus3 at ixpide1 channel 1
azalia1 at pci0 dev 20 function 2: Generic High Definition Audio Controller
azalia1: interrupting at ioapic0 pin 16
azalia1: host: 0x1002/0x4383 (rev. 0), HDA rev. 1.0
pcib0 at pci0 dev 20 function 3
pcib0: vendor 0x1002 product 0x439d (rev. 0x00)
ppb3 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x00)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled
ohci4 at pci0 dev 20 function 5: vendor 0x1002 product 0x4399 (rev. 0x00)
ohci4: interrupting at ioapic0 pin 18
ohci4: OHCI version 1.0, legacy support
usb6 at ohci4: USB revision 1.0
pchb1 at pci0 dev 24 function 0
pchb1: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb2 at pci0 dev 24 function 1
pchb2: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb3 at pci0 dev 24 function 2
pchb3: vendor 0x1022 product 0x1102 (rev. 0x00)
amdtemp0 at pci0 dev 24 function 3
amdtemp0: AMD CPU Temperature Sensors (K8: core rev DH-F3)
isa0 at pcib0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: ATI RS690/780 HDMI (rev. 0.0), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
azalia1: codec[3]: Realtek ALC662-GR (rev. 1.1), HDA rev. 1.0
audio1 at azalia1: full duplex, independent
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
uhub2 at usb2: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
uhub3 at usb3: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 3 ports with 3 removable, self powered
uhub4 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 3 ports with 3 removable, self powered
uhub5 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 6 ports with 6 removable, self powered
uhub6 at usb6: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
uhub7 at uhub2 port 3: vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/7.02, addr 
2
uhub7: single transaction translator
uhub7: 4 ports with 4 removable, self powered
uhub8 at uhub7 port 1: vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/7.02, addr 
3
uhub8: single transaction translator
uhub8: 4 ports with 4 removable, self powered
wd0 at atabus0 drive 0: <HTS721010G9SA00>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 95396 MB, 193821 cyl, 16 head, 63 sec, 512 bytes/sect x 195371568 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(ixpide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus2: 2 targets
cd0 at atapibus0 drive 0: <Optiarc  DVD RW AD-7633A, , 1.00> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(ixpide1:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
uhub9 at uhub8 port 1: Lite-On Tech USB 1.1 2 port downstream low-power hub, 
class 9/0, rev 1.10/1.26, addr 4
uhub9: 4 ports with 2 removable, bus powered
uhidev0 at uhub9 port 3 configuration 1 interface 0
uhidev0: Lite-On Tech IBM USB Travel Keyboard with UltraNav, rev 1.10/1.16, 
addr 5, iclass 3/1
ukbd0 at uhidev0
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub9 port 3 configuration 1 interface 1
uhidev1: Lite-On Tech IBM USB Travel Keyboard with UltraNav, rev 1.10/1.16, 
addr 5, iclass 3/0
uhidev1: 3 report ids
uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=3, output=0, feature=0
uhidev2 at uhub9 port 4 configuration 1 interface 0
uhidev2: Synaptics Inc. Composite TouchPad / TrackPoint, rev 1.10/0.15, addr 6, 
iclass 3/1
ums0 at uhidev2: 3 buttons
wsmouse0 at ums0 mux 0
uhidev3 at uhub9 port 4 configuration 1 interface 1
uhidev3: Synaptics Inc. Composite TouchPad / TrackPoint, rev 1.10/0.15, addr 6, 
iclass 3/1
ums1 at uhidev3: 3 buttons
wsmouse1 at ums1 mux 0
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio2 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

Follow-Ups:
- Re: ixpide0:0:0: lost interrupt hang
  - From: Manuel Bouyer

Prev by Date: Re: boot(8) diffs
Next by Date: Re: ixpide0:0:0: lost interrupt hang
Previous by Thread: Intel G43 integrated graphics on -current
Next by Thread: Re: ixpide0:0:0: lost interrupt hang
Indexes:

Home | Main Index | Thread Index | Old Index