USB Printer support

[Pete Rushmere <pete%rushmere.org@localhost>]

Hi All,

Trying to set the Qube up as a print server, but I have run into problems...

Compiled a new 4.0 kernel, added ehci support for good measure - all seems OK 
so far. Qube is equipped with a Belkin 5 port USB card. The Qube recognises 
the printer at ulpt0 as per dmesg...

NetBSD 4.0 (MYKERNEL) #2: Sat May 17 16:14:04 BST 2008
        
pete%qube.rushmere.org@localhost:/usr/src/sys/arch/cobalt/compile/MYKERNEL
Cobalt Qube 2
total memory = 256 MB
avail memory = 246 MB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root)
com0 at mainbus0 addr 0x1c800000 level 3: st16650a, working fifo
com0: console
cpu0 at mainbus0: QED RM5200 CPU (0x28a0) Rev. 10.0 with built-in FPU Rev. 
10.0
cpu0: 32KB/32B 2-way set-associative L1 Instruction cache, 48 TLB entries
cpu0: 32KB/32B 2-way set-associative write-back L1 Data cache
mcclock0 at mainbus0 addr 0x10000070: mc146818 compatible time-of-day clock
panel0 at mainbus0 addr 0x1f000000
gt0 at mainbus0 addr 0x14000000
pci0 at gt0
pci0: i/o space, memory space enabled, rd/line, wr/inv ok
pchb0 at pci0 dev 0 function 0: Galileo GT-64111 System Controller, rev 1
tlp0 at pci0 dev 7 function 0: DECchip 21143 Ethernet, pass 4.1
tlp0: interrupting at level 1
tlp0: Ethernet address 00:10:e0:00:49:c4
lxtphy0 at tlp0 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 9 function 0
pcib0: VIA Technologies VT82C586 PCI-ISA Bridge, rev 39
viaide0 at pci0 dev 9 function 1
viaide0: VIA Technologies VT82C586 (Apollo VP) ATA33 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
uhci0 at pci0 dev 9 function 2: VIA Technologies VT83C572 USB Controller (rev. 
0x02)
uhci0: can't map i/o space
ohci0 at pci0 dev 10 function 0: NEC USB Host Controller (rev. 0x43)
ohci0: interrupting at irq 9
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1 at pci0 dev 10 function 1: NEC USB Host Controller (rev. 0x43)
ohci1: interrupting at irq 9
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 10 function 2: NEC USB Host Controller (rev. 0x04)
ehci0: interrupting at irq 9
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 5 ports with 5 removable, self powered
tlp1 at pci0 dev 12 function 0: DECchip 21143 Ethernet, pass 4.1
tlp1: interrupting at level 2
tlp1: Ethernet address 00:10:e0:00:48:05
lxtphy1 at tlp1 phy 1: LXT970 10/100 media interface, rev. 3
lxtphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mips3_cp0_counter" frequency 125000000 Hz quality 
100
Kernelized RAIDframe activated
ulpt0 at uhub0 port 3 configuration 1 interface 0
ulpt0: Brother HL-2030 series, rev 2.00/1.00, addr 2, iclass 7/1
ulpt0: using bi-directional mode
wd0 at atabus0 drive 0: <SAMSUNG SP0411N>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 32253 MB, 65531 cyl, 16 head, 63 sec, 512 bytes/sect x 66055248 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs

So, I do 'sh /dev/MAKEDEV usbs' which should build the device nodes for the 
usb subsystems, and I get:

root@qube:/home/pete sh /dev/MAKEDEV usbs
/dev/MAKEDEV: usb: unknown device
/dev/MAKEDEV: usb0: unknown device
/dev/MAKEDEV: usb1: unknown device
/dev/MAKEDEV: usb2: unknown device
/dev/MAKEDEV: usb3: unknown device
/dev/MAKEDEV: usb4: unknown device
/dev/MAKEDEV: usb5: unknown device
/dev/MAKEDEV: usb6: unknown device
/dev/MAKEDEV: usb7: unknown device
/dev/MAKEDEV: uhid0: unknown device
/dev/MAKEDEV: uhid1: unknown device
/dev/MAKEDEV: uhid2: unknown device
/dev/MAKEDEV: uhid3: unknown device
/dev/MAKEDEV: ulpt0: unknown device
/dev/MAKEDEV: ulpt1: unknown device
/dev/MAKEDEV: ttyU0: unknown device
/dev/MAKEDEV: ttyU1: unknown device
/dev/MAKEDEV: urio0: unknown device
/dev/MAKEDEV: uscanner0: unknown device
/dev/MAKEDEV: uscanner1: unknown device
/dev/MAKEDEV: ugen0: unknown device

As you can see, it won't build the ulpt* device node for the printer. I'm 
stuck now... Any ideas?

Cheers,
Pete.