Port-arm archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

Illegal instruction errors on RPI3 with NetBSD-8



	hello.  I just built and loaded a full release of NetBSD-8 on an RPI3.
I'm unable to boot into multi-user mode because a number of programs are
dying with illegal instruction errors, including fsck and ifconfig.  Also,
the serial console intermittently accepts input.  I'm using the latest
bootcode.bin file from the build image.  This problem isn't entirely new, I
was having issues with 7.99.41 back in November of 2016, but I figured it
was due to the relatively new support of the RPI3 at that time.
Any idea if this is a software or hardware problem?  The boot output is
below.

-thanks
-Brian


NetBSD/evbarm (rpi) booting ...
[ Kernel symbol table missing! ]
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 8.0_BETA (RPI2) #0: Wed Jul 26 00:51:28 PDT 2017
	buhrow%lothlorien.nfbcal.org@localhost:/usr/local/netbsd/obj-rpi/sys/arch/evbarm/compile/RPI2
total memory = 944 MB
avail memory = 925 MB
sysctl_createv: sysctl_create(machine_arch) returned 17
mainbus0 (root)
cpu0 at mainbus0 core 0: 600 MHz Cortex-A53 r0p4 (Cortex V8A core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB/64B 2-way L1 VIPT Instruction cache
cpu0: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache
cpu0: 512KB/64B 16-way write-through L2 PIPT Unified cache
vfp0 at cpu0: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu1 at mainbus0 core 1
cpu2 at mainbus0 core 2
cpu3 at mainbus0 core 3
obio0 at mainbus0
bcmicu0 at obio0: Multiprocessor
armgtmr0 at obio0: ARMv7 Generic 64-bit Timer (19200 kHz)
armgtmr0: interrupting on irq 3
bcmmbox0 at obio0 intr 193: VC mailbox
vcmbox0 at bcmmbox0
vchiq0 at obio0 intr 194: BCM2835 VCHIQ
bcmpm0 at obio0: Power management, Reset and Watchdog controller
bcmdmac0 at obio0: DMA0 DMA2 DMA4 DMA5 DMA8 DMA9 DMA10
bcmrng0 at obio0: RNG
plcom0 at obio0 intr 185
plcom0: txfifo disabled
plcom0: console
genfb0 at obio0
wsdisplay0 at genfb0 kbdmux 1
sdhc0 at obio0 intr 190: SDHC controller
sdhc0: interrupting on intr 190
dwctwo0 at obio0 intr 137: USB controller
bcmspi0 at obio0 intr 182: SPI
spi0 at bcmspi0: SPI bus
bsciic0 at obio0 intr 181: disabled
bsciic1 at obio0 intr 181: BSC1
iic0 at bsciic1: I2C bus
bcmgpio0 at obio0: GPIO [0...31]
gpio0 at bcmgpio0: 32 pins
bcmgpio1 at obio0: GPIO [32...53]
gpio1 at bcmgpio1: 22 pins
bcmcm at obio0 not configured
bcmpwm at obio0 not configured
usb0 at dwctwo0: USB revision 2.0
cpu1: 600 MHz Cortex-A53 r0p4 (Cortex V8A core)
cpu1: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu1: 32KB/64B 2-way L1 VIPT Instruction cache
cpu1: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache
cpu1: 512KB/64B 16-way write-through L2 PIPT Unified cache
vfp1 at cpu1: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu2: 600 MHz Cortex-A53 r0p4 (Cortex V8A core)
cpu2: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu2: 32KB/64B 2-way L1 VIPT Instruction cache
cpu2: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache
cpu2: 512KB/64B 16-way write-through L2 PIPT Unified cache
vfp2 at cpu2: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
cpu3: 600 MHz Cortex-A53 r0p4 (Cortex V8A core)
cpu3: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu3: 32KB/64B 2-way L1 VIPT Instruction cache
cpu3: 32KB/64B 4-way write-back-locking-C L1 PIPT Data cache
cpu3: 512KB/64B 16-way write-through L2 PIPT Unified cache
vfp3 at cpu3: NEON MPE (VFP 3.0+), rounding, NaN propagation, denormals
sdhc0: SDHC 3.0, rev 153, platform DMA, 250000 kHz, HS 3.3V, re-tuning mode 1, 1024 byte blocks
sdmmc0 at sdhc0 slot 0
uhub0 at usb0: vendor 0000 (0000) DWC2 root hub (0000), class 9/0, rev 2.00/1.00, addr 1
sdmmc0: SD card status: 4-bit, C10, U1
ld0 at sdmmc0: <0x1b:0x534d:00000:0x10:0x09f15f20:0x106>
ld0: 30543 MB, 7756 cyl, 128 head, 63 sec, 512 bytes/sect x 62552064 sectors
ld0: 4-bit width, High-Speed/SDR25, 50.000 MHz
uhub1 at uhub0 port 1: vendor 0424 (0x424) product 9514 (0x9514), class 9/0, rev 2.00/2.00, addr 2
uhub1: multiple transaction translators
usmsc0 at uhub1 port 1
usmsc0: vendor 0424 (0x424) product ec00 (0xec00), rev 2.00/2.00, addr 3
usmsc0: Ethernet address b8:27:eb:92:4d:59
ukphy0 at usmsc0 phy 1: OUI 0x00800f, model 0x000c, rev. 3
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
uhub0: illegal enable change, port 1
WARNING: 1 error while detecting hardware; check system log.
boot device: ld0
root on ld0a dumps on ld0b
root file system type: ffs
kern.module.path=/stand/evbarm/8.0/modules
vcaudio0 at vchiq0: auds
WARNING: no TOD clock present
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
audio0 at vcaudio0: half duplex, playback, capture, mmap, independent
vcaudio0: Virtual format configured - Format SLINEAR, precision 16, channels 2, frequency 48000
spkr0 at audio0: PC Speaker (synthesized)
Wed Jul 26 11:25:31 PDT 2017
Starting root file system check:
fsck: /dev/rld0a: Illegal instruction
Automatic file system check failed; help!
ERROR: ABORTING BOOT (sending SIGTERM to parent)!
[1]   Terminated              (stty status "^T...
Enter pathname of shell or RETURN for /bin/sh: 


Home | Main Index | Thread Index | Old Index