kern/40531: 5.0_BETA/i386 doesn't power off on Dell Latitude X1 with CF card plugged in

[denbrok%uni-bonn.de@localhost]

>Number:         40531
>Category:       kern
>Synopsis:       5.0_BETA/i386 doesn't power off on Dell Latitude X1 with CF 
>card plugged in
>Confidential:   no
>Severity:       serious
>Priority:       medium
>Responsible:    kern-bug-people
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Sun Feb 01 16:00:00 +0000 2009
>Originator:     Dennis den Brok
>Release:        5.0_BETA
>Organization:
-
>Environment:
NetBSD 5.0_BETA i386
>Description:
As in one-line summary. Unplugging the CF card solves the problem, which didn't 
occur at all under 4.0.1.

dmesg output:

NetBSD 5.0_BETA (GENERIC) #0: Fri Jan 23 00:16:07 UTC 2009
        
builds%b0.netbsd.org@localhost:/home/builds/ab/netbsd-5/i386/200901220000Z-obj/home/builds/ab/netbsd-5/src/sys/arch/i386/compile/GENERIC
total memory = 1271 MB
avail memory = 1237 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Dell Inc. Latitude X1                     
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 1097MHz, id 0x6d8
cpu0: Enhanced SpeedStep (940 mV) 1100 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 1100 1000 900 800 600
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <DELL  , CPi R  ,27d50c19>, AslId <ASL ,00000061>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 24-bit timer
acpiacad0 at acpi0 (AC, ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (BAT0, PNP0C0A-1): ACPI Battery (Control Method)
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PBTN, PNP0C0C): ACPI Power Button
acpibut1 at acpi0 (SBTN, PNP0C0E): ACPI Sleep Button
pckbc1 at acpi0 (PS2M, PNP0F13): aux port
pckbc1: irq 12
pckbc2 at acpi0 (KBC, PNP0303): kbd port
pckbc2: io 0x60,0x64,0x62,0x66 irq 1
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x43,0x50-0x53 irq 2
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61,0x63,0x65,0x67
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
acpitz0 at acpi0 (THM): critical 95.0C, passive cooling
apm0 at acpi0: Power Management spec V1.2
pckbd0 at pckbc2 (kbd slot)
pckbc2: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc2 (aux slot)
pms0: Synaptics touchpad version 6.2
pms0: Palm detect, Multi-finger
pckbc2: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x2590 (rev. 0x03)
agp0 at pchb0: detected 7932k stolen memory
agp0: aperture at 0xc0000000, size 0x10000000
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x2592 (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
vendor 0x8086 product 0x2792 (miscellaneous display, revision 0x03) at pci0 dev 
2 function 1 not configured
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x2660 (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci1 dev 0 function 0: Broadcom BCM5751 Gigabit Ethernet
bge0: interrupting at ioapic0 pin 16
bge0: ASIC BCM5750 A1 (0x4001), Ethernet address 00:13:72:6a:f5:80
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5750 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x2658 (rev. 0x03)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 2: vendor 0x8086 product 0x265a (rev. 0x03)
uhci1: interrupting at ioapic0 pin 18
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 3: vendor 0x8086 product 0x265b (rev. 0x03)
uhci2: interrupting at ioapic0 pin 19
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x265c (rev. 0x03)
ehci0: interrupting at ioapic0 pin 16
ehci0: EHCI version 1.0
ehci0: wrong number of companions (4 != 3)
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
ppb1 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xd3)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
cbb0 at pci2 dev 1 function 0: vendor 0x1180 product 0x0476 (rev. 0xb3)
fwohci0 at pci2 dev 1 function 1: vendor 0x1180 product 0x0552 (rev. 0x08)
fwohci0: interrupting at ioapic0 pin 18
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 32:4f:c0:00:04:15:a4:50
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
vendor 0x1180 product 0x0822 (SD Host Controller system, interface 0x01, 
revision 0x17) at pci2 dev 1 function 2 not configured
iwi0 at pci2 dev 3 function 0: vendor 0x8086 product 0x4220 (rev. 0x05)
iwi0: interrupting at ioapic0 pin 17
iwi0: 802.11 address 00:16:6f:73:96:e2
iwi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
iwi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 
36Mbps 48Mbps 54Mbps
cbb0: cacheline 0x0 lattimer 0x40
cbb0: bhlc 0x824000
cbb0: interrupting at ioapic0 pin 19
cardslot0 at cbb0
cardbus0 at cardslot0: bus 3
pcmcia0 at cardslot0
auich0 at pci0 dev 30 function 2: i82801FB (ICH6) AC-97 Audio
auich0: interrupting at ioapic0 pin 16
auich0: ac97: SigmaTel STAC9752/53 codec; headphone, 20 bit DAC, 20 bit ADC, 
SigmaTel 3D
auich0: ac97: ext id a01<AC97_23,AMAP,VRA>
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x2641 (rev. 0x03)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801FB IDE Controller (ICH6) (rev. 0x03)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x266a (rev. 0x03)
ichsmb0: interrupting at SMI
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
acpiacad0: AC adapter online.
auich0: measured ac97 link rate at 47998 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 8 ports with 8 removable, self powered
wdc2 at pcmcia0 function 0: <TRANSCEND, TS1GCF80, >
wdc2: i/o mapped mode
atabus1 at wdc2 channel 0
wd0 at atabus0 drive 0: <SanDisk SDCFX3-004G>
wd0: drive supports 4-sector PIO transfers, LBA addressing
wd0: 3919 MB, 7964 cyl, 16 head, 63 sec, 512 bytes/sect x 8027712 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
wd1 at atabus1 drive 0: <TRANSCEND>
wd1: drive supports 1-sector PIO transfers, LBA addressing
wd1: 991 MB, 2014 cyl, 16 head, 63 sec, 512 bytes/sect x 2030112 sectors
wd1: drive supports PIO mode 4
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
>How-To-Repeat:

>Fix: