tech-kern archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: cpu1: failed to start (amd64)
On 2018-05-26 00:21, Greg Troxel wrote:
Did you try no SMP, but leaving ACPI?
It would help to give motherboard brand/model, too,
Thanks Greg, it successfully boots with ACPI and no SMP.
(see attached dmesg-no-smp.txt)
The motherboard is an Intel DG965WH.
I tried adding some aprint_normal_dev() calls to cpu_hatch() but was
having difficulty seeing the output as it scrolled past. So I started
removing devices from the kernel config and stumbled upon a combination
that allowed the kernel to boot. For the time being I have stopped this
printf debugging to follow up device config combinations.
The kernel boots if I remove
uhci* at pci? dev ? function ?
but then the USB drive is not detected and the boot device is not found.
The system has five uchi entries across two dev numbers. Enabling
specific
devices such as:
uhci4 at pci0 dev 29 function 2
allows the kernel to boot, but I have not yet got it to detect the USB
drive in any combinations I have tried so far.
If I enable all five devices specifying dev and function numbers then it
boots but pauses for a very long time (maybe 30+ seconds). I wondered if
there USB retries/errors not being displayed so I turned on USBVERBOSE
but saw no additional output.
Any more suggestions to direct my trouble shooting?
Is it worth connecting up a serial output to capture failed boots? I can
then continue the printf debugging technique but am unsure of what I am
looking for...
Michael.
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
2018 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 7.1.2 (GENERIC.201803151611Z)
total memory = 4021 MB
avail memory = 3887 MB
kern.module.path=/stand/amd64/7.1/modules
timecounter: Timecounters tick every 10.000 msec
RTC BIOS diagnostic error 0x80<clock_battery>
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
( )
mainbus0 (root)
ACPI: RSDP 0xfe020 000014 (v00 INTEL )
ACPI: RSDT 0xcf6fd038 000050 (v01 INTEL DG965WH 00000697 01000013)
ACPI: FACP 0xcf6fc000 000074 (v01 INTEL DG965WH 00000697 MSFT 01000013)
ACPI: DSDT 0xcf6f7000 0040ED (v01 INTEL DG965WH 00000697 MSFT 01000013)
ACPI: FACS 0xcf6a0000 000040
ACPI: APIC 0xcf6f6000 000078 (v01 INTEL DG965WH 00000697 MSFT 01000013)
ACPI: WDDT 0xcf6f5000 000040 (v01 INTEL DG965WH 00000697 MSFT 01000013)
ACPI: MCFG 0xcf6f4000 00003C (v01 INTEL DG965WH 00000697 MSFT 01000013)
ACPI: ASF! 0xcf6f3000 0000A6 (v32 INTEL DG965WH 00000697 MSFT 01000013)
ACPI: HPET 0xcf6f2000 000038 (v01 INTEL DG965WH 00000697 MSFT 01000013)
ACPI: SSDT 0xcf6f0000 0001BC (v01 INTEL CpuPm 00000697 MSFT 01000013)
ACPI: SSDT 0xcf6ef000 000175 (v01 INTEL Cpu0Ist 00000697 MSFT 01000013)
ACPI: SSDT 0xcf6ee000 000175 (v01 INTEL Cpu1Ist 00000697 MSFT 01000013)
ACPI: SSDT 0xcf6ed000 000175 (v01 INTEL Cpu2Ist 00000697 MSFT 01000013)
ACPI: SSDT 0xcf6ec000 000175 (v01 INTEL Cpu3Ist 00000697 MSFT 01000013)
ACPI: All ACPI Tables successfully acquired
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x20, 24 pins
cpu0 at mainbus0 apid 0: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz, id 0x6fb
cpu1 at mainbus0 apid 2: multiprocessor boot disabled
cpu2 at mainbus0 apid 1: multiprocessor boot disabled
cpu3 at mainbus0 apid 3: multiprocessor boot disabled
acpi0 at mainbus0: Intel ACPICA 20131218
acpi0: X/RSDT: OemId <INTEL ,DG965WH ,00000697>, AslId < ,01000013>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
IOCM (PNP0C02) at acpi0 not configured
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
XTRA (PNP0C02) at acpi0 not configured
ECP (PNP0401) at acpi0 not configured
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
UAR1 (PNP0501) at acpi0 not configured
IELK (AWY0001) at acpi0 not configured
APIC (PNP0003) at acpi0 not configured
ACPI: Enabled 4 GPEs in block 00 to 1F
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20131218/hwxface-646)
ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20131218/hwxface-646)
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x29a0 (rev. 0x02)
agp0 at pchb0: i965-family chipset
agp0: detected 7676k stolen memory
agp0: aperture at 0xd0000000, size 0x20000000
i915drmkms0 at pci0 dev 2 function 0: vendor 0x8086 product 0x29a2 (rev. 0x02)
drm: Memory usable by graphics device = 512M
drm: Supports vblank timestamp caching Rev 2 (21.10.2013).
drm: Driver supports precise vblank timestamp query.
i915drmkms0: interrupting at ioapic0 pin 16 (i915)
drm: initialized overlay support
intelfb0 at i915drmkms0
i915drmkms0: info: registered panic notifier
intelfb0: framebuffer at 0xffff8000478b0000, size 1280x1024, depth 32, stride 5120
wsdisplay0 at intelfb0 kbdmux 1: console (default, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
vendor 0x8086 product 0x29a4 (miscellaneous communications, revision 0x02) at pci0 dev 3 function 0 not configured
wm0 at pci0 dev 25 function 0: Intel i82801H LAN Controller (rev. 0x02)
wm0: interrupting at ioapic0 pin 20
wm0: PCI-Express bus
wm0: 2048 words FLASH
wm0: Ethernet address XX:XX:XX:XX:XX:XX
igphy0 at wm0 phy 1: i82566 10/100/1000 media interface, rev. 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x2834 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x2835 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 21
usb1 at uhci1: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x283a (rev. 0x02)
ehci0: interrupting at ioapic0 pin 18
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1
usb2 at ehci0: USB revision 2.0
hdaudio0 at pci0 dev 27 function 0: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 22
hdafg0 at hdaudio0: Sigmatel STAC9271D
hdafg0: DAC00 6ch: Speaker [Jack], HP Out [Jack]
hdafg0: ADC01 2ch: Line In [Jack], Mic In [Jack]
hdafg0: ADC02 2ch: Mic In [Jack]
hdafg0: DIG03 2ch: SPDIF Out [Jack]
hdafg0: 6ch/2ch 44100Hz 48000Hz 88200Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x283f (rev. 0x02)
ppb0: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x2841 (rev. 0x02)
ppb1: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
pciide0 at pci2 dev 0 function 0: vendor 0x11ab product 0x6101 (rev. 0xb1)
pciide0: bus-master DMA support present, but unused (no driver support)
pciide0: primary channel configured to native-PCI mode
pciide0: using ioapic0 pin 17 for native-PCI interrupt
atabus0 at pciide0 channel 0
pciide0: secondary channel configured to native-PCI mode
atabus1 at pciide0 channel 1
ppb2 at pci0 dev 28 function 2: vendor 0x8086 product 0x2843 (rev. 0x02)
ppb2: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 28 function 3: vendor 0x8086 product 0x2845 (rev. 0x02)
ppb3: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 28 function 4: vendor 0x8086 product 0x2847 (rev. 0x02)
ppb4: PCI Express capability version 1 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
uhci2 at pci0 dev 29 function 0: vendor 0x8086 product 0x2830 (rev. 0x02)
uhci2: interrupting at ioapic0 pin 23
usb3 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 1: vendor 0x8086 product 0x2831 (rev. 0x02)
uhci3: interrupting at ioapic0 pin 19
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 2: vendor 0x8086 product 0x2832 (rev. 0x02)
uhci4: interrupting at ioapic0 pin 18
usb5 at uhci4: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x2836 (rev. 0x02)
ehci1: interrupting at ioapic0 pin 23
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci2 uhci3 uhci4
usb6 at ehci1: USB revision 2.0
ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xf2)
pci6 at ppb5 bus 6
pci6: i/o space, memory space enabled
fwohci0 at pci6 dev 3 function 0: vendor 0x104c product 0x8023 (rev. 0x00)
fwohci0: interrupting at ioapic0 pin 19
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 XX:XX:XX:XX:XX:XX:XX:XX
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
ichlpcib0 at pci0 dev 31 function 0: vendor 0x8086 product 0x2812 (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
ahcisata0 at pci0 dev 31 function 2: vendor 0x8086 product 0x2821 (rev. 0x02)
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.10, 6 ports, 32 slots, CAP 0xe320ffc5<EMS,CCCS,PSC,SSC,PMD,ISS=0x2=Gen2,SCLO,SAL,SSNTF,SNCQ,S64A>
atabus2 at ahcisata0 channel 0
atabus3 at ahcisata0 channel 1
atabus4 at ahcisata0 channel 2
atabus5 at ahcisata0 channel 3
atabus6 at ahcisata0 channel 4
atabus7 at ahcisata0 channel 5
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x283e (rev. 0x02)
ichsmb0: interrupting at ioapic0 pin 21
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: HLT, lat 0 us, pow 0 mW
acpicpu0: P0: FFH, lat 10 us, pow 89000 mW, 2394 MHz
acpicpu0: P1: FFH, lat 10 us, pow 56960 mW, 1596 MHz
acpicpu0: T0: I/O, lat 1 us, pow 0 mW, 100 %
acpicpu0: T1: I/O, lat 1 us, pow 0 mW, 88 %
acpicpu0: T2: I/O, lat 1 us, pow 0 mW, 76 %
acpicpu0: T3: I/O, lat 1 us, pow 0 mW, 64 %
acpicpu0: T4: I/O, lat 1 us, pow 0 mW, 52 %
acpicpu0: T5: I/O, lat 1 us, pow 0 mW, 40 %
acpicpu0: T6: I/O, lat 1 us, pow 0 mW, 28 %
acpicpu0: T7: I/O, lat 1 us, pow 0 mW, 16 %
coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
atapibus0 at atabus0: 2 targets
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub6: 6 ports with 6 removable, self powered
cd0 at atapibus0 drive 0: <PIONEER DVD-RW DVR-110D, EHDC152514WL, 1.08> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
IPsec: Initialized Security Association Processing.
umass0 at uhub6 port 5 configuration 1 interface 0
umass0: SanDisk Cruzer Fit, rev 2.00/1.27, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <SanDisk, Cruzer Fit, 1.27> disk removable
sd0: 7633 MB, 15509 cyl, 16 head, 63 sec, 512 bytes/sect x 15633408 sectors
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
Home |
Main Index |
Thread Index |
Old Index