Re: wm0 stopped receiving after mpt0 timeout recovery

To: tech-kern%netbsd.org@localhost
Subject: Re: wm0 stopped receiving after mpt0 timeout recovery
From: Edgar Fuß <ef%math.uni-bonn.de@localhost>
Date: Tue, 5 Jul 2016 11:42:30 +0200

> Please show the full dmesg.
Attached.

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.1_STABLE (MI-Server) #6: Mon Feb 15 13:45:03 CET 2016
	support%trave.math.uni-bonn.de@localhost:/usr/obj/sys/arch/amd64/compile/miserv
total memory = 16366 MB
avail memory = 15883 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Supermicro H8SCM (1234567890)
mainbus0 (root)
cpu0 at mainbus0 apid 16: AMD Opteron(tm) Processor 4226                 , id 0x600f12
cpu1 at mainbus0 apid 17: AMD Opteron(tm) Processor 4226                 , id 0x600f12
cpu2 at mainbus0 apid 18: AMD Opteron(tm) Processor 4226                 , id 0x600f12
cpu3 at mainbus0 apid 19: AMD Opteron(tm) Processor 4226                 , id 0x600f12
cpu4 at mainbus0 apid 20: AMD Opteron(tm) Processor 4226                 , id 0x600f12
cpu5 at mainbus0 apid 21: AMD Opteron(tm) Processor 4226                 , id 0x600f12
ioapic0 at mainbus0 apid 0: pa 0xfec00000, version 21, 24 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <SMCI  ,        ,20111111>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
NMEM (PNP0C02) at acpi0 not configured
UMEM (PNP0C02) at acpi0 not configured
attimer0 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pckbc0 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc1 at acpi0 (PS2M, PNP0F03) (aux port): irq 12
pcppi0 at acpi0 (SPKR, PNP0800): io 0x61
spkr0 at pcppi0
sysbeep0 at pcppi0
SIOR (PNP0C02) at acpi0 not configured
OMSC (PNP0C02) at acpi0 not configured
RMSC (PNP0C02) at acpi0 not configured
com0 at acpi0 (UAR1, PNP0501-1): io 0x3f8-0x3ff irq 4
com0: ns16550a, working fifo
com1 at acpi0 (UAR2, PNP0501-2): io 0x2f8-0x2ff irq 3
com1: ns16550a, working fifo
PCIE (PNP0C02) at acpi0 not configured
RMEM (PNP0C01) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
attimer0: attached to pcppi0
ipmi0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x1002 product 0x5a13 (rev. 0x02)
vendor 0x1002 product 0x5a23 (system, subclass 0x06) at pci0 dev 0 function 2 not configured
ppb0 at pci0 dev 3 function 0: vendor 0x1002 product 0x5a17 (rev. 0x00)
ppb0: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
mpt0 at pci1 dev 0 function 0: vendor 0x1000 product 0x0058 (rev. 0x08)
mpt0: interrupting at ioapic0 pin 19
mpt0: Phy 0: Link Rate 3.0 Gbps
mpt0: Phy 1: Link Rate 3.0 Gbps
mpt0: Phy 2: Link Rate 3.0 Gbps
mpt0: Phy 3: Link Rate 3.0 Gbps
scsibus0 at mpt0: 112 targets, 8 luns per target
ppb1 at pci0 dev 9 function 0: vendor 0x1002 product 0x5a1c (rev. 0x00)
ppb1: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
wm0 at pci2 dev 0 function 0: Intel i82574L (rev. 0x00)
wm0: interrupting at ioapic0 pin 17
wm0: PCI-Express bus
wm0: 2048 words (8 address bits) SPI EEPROM
wm0: Ethernet address 00:25:90:57:ee:00
ukphy0 at wm0 phy 1: OUI 0x000ac2, model 0x000b, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb2 at pci0 dev 10 function 0: vendor 0x1002 product 0x5a1d (rev. 0x00)
ppb2: PCI Express 2.0 <Root Port of PCI-E Root Complex>
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
wm1 at pci3 dev 0 function 0: Intel i82574L (rev. 0x00)
wm1: interrupting at ioapic0 pin 18
wm1: PCI-Express bus
wm1: 2048 words (8 address bits) SPI EEPROM
wm1: Ethernet address 00:25:90:57:ee:01
ukphy1 at wm1 phy 1: OUI 0x000ac2, model 0x000b, rev. 1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ahcisata0 at pci0 dev 17 function 0: vendor 0x1002 product 0x4391 (rev. 0x00)
ahcisata0: interrupting at ioapic0 pin 22
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.10, 6 ports, 32 slots, CAP 0xf722ff85<CCCS,PSC,SSC,PMD,SPM,ISS=0x2=Gen2,SCLO,SAL,SALP,SMPS,SSNTF,SNCQ,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 2
atabus3 at ahcisata0 channel 3
atabus4 at ahcisata0 channel 4
atabus5 at ahcisata0 channel 5
ohci0 at pci0 dev 18 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 16
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 18 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 16
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ehci0 at pci0 dev 18 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci0: interrupting at ioapic0 pin 17
ehci0: dropped intr workaround enabled
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
ohci2 at pci0 dev 19 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2: OHCI version 1.0, legacy support
usb3 at ohci2: USB revision 1.0
ohci3 at pci0 dev 19 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci3: interrupting at ioapic0 pin 18
ohci3: OHCI version 1.0, legacy support
usb4 at ohci3: USB revision 1.0
ehci1 at pci0 dev 19 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci1: interrupting at ioapic0 pin 19
ehci1: dropped intr workaround enabled
ehci1: EHCI version 1.0
ehci1: companion controllers, 3 ports each: ohci2 ohci3
usb5 at ehci1: USB revision 2.0
piixpm0 at pci0 dev 20 function 0: vendor 0x1002 product 0x4385 (rev. 0x3d)
piixpm0: interrupting at SMI, polling
iic0 at piixpm0: I2C bus
spdmem0 at iic0 addr 0x50
spdmem0: DDR3 SDRAM (registered), ECC, temp-sensor, 4GB, 1333MHz (PC3-10666)
spdmem0: 11 rows, 14 cols, 8 log. banks, 2 phys. banks, 1.500ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 8-8-8-24
spdmem1 at iic0 addr 0x51
spdmem1: DDR3 SDRAM (registered), ECC, temp-sensor, 4GB, 1333MHz (PC3-10666)
spdmem1: 11 rows, 14 cols, 8 log. banks, 2 phys. banks, 1.500ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 8-8-8-24
spdmem2 at iic0 addr 0x52
spdmem2: DDR3 SDRAM (registered), ECC, temp-sensor, 4GB, 1333MHz (PC3-10666)
spdmem2: 11 rows, 14 cols, 8 log. banks, 2 phys. banks, 1.500ns cycle time
spdmem2: tAA-tRCD-tRP-tRAS: 8-8-8-24
spdmem3 at iic0 addr 0x53
spdmem3: DDR3 SDRAM (registered), ECC, temp-sensor, 4GB, 1333MHz (PC3-10666)
spdmem3: 11 rows, 14 cols, 8 log. banks, 2 phys. banks, 1.500ns cycle time
spdmem3: tAA-tRCD-tRP-tRAS: 8-8-8-24
dbcool_chip_ident: addr 0x2e c_id 0x00 d_id 0x00 r_id 0x00: No match.
ixpide0 at pci0 dev 20 function 1: ATI Technologies IXP IDE Controller (rev. 0x00)
ixpide0: bus-master DMA support present
ixpide0: primary channel configured to compatibility mode
ixpide0: primary channel interrupting at ioapic0 pin 14
atabus6 at ixpide0 channel 0
ixpide0: secondary channel configured to compatibility mode
ixpide0: secondary channel interrupting at ioapic0 pin 15
atabus7 at ixpide0 channel 1
pcib0 at pci0 dev 20 function 3: vendor 0x1002 product 0x439d (rev. 0x00)
ppb3 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x00)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled
vga0 at pci4 dev 4 function 0: vendor 0x102b product 0x0532 (rev. 0x0a)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
ohci4 at pci0 dev 20 function 5: vendor 0x1002 product 0x4399 (rev. 0x00)
ohci4: interrupting at ioapic0 pin 18
ohci4: OHCI version 1.0, legacy support
usb6 at ohci4: USB revision 1.0
pchb1 at pci0 dev 24 function 0: vendor 0x1022 product 0x1600 (rev. 0x00)
pchb2 at pci0 dev 24 function 1: vendor 0x1022 product 0x1601 (rev. 0x00)
pchb3 at pci0 dev 24 function 2: vendor 0x1022 product 0x1602 (rev. 0x00)
pchb4 at pci0 dev 24 function 3: vendor 0x1022 product 0x1603 (rev. 0x00)
amdtemp0 at pchb4: AMD CPU Temperature Sensors (Family15h)
pchb5 at pci0 dev 24 function 4: vendor 0x1022 product 0x1604 (rev. 0x00)
pchb6 at pci0 dev 24 function 5: vendor 0x1022 product 0x1605 (rev. 0x00)
isa0 at pcib0
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: HLT, lat   0 us, pow     0 mW
acpicpu0: C2: I/O, lat 100 us, pow     0 mW
acpicpu0: P0: FFH, lat   5 us, pow 13440 mW, 2700 MHz
acpicpu0: P1: FFH, lat   5 us, pow 10806 mW, 2400 MHz
acpicpu0: P2: FFH, lat   5 us, pow  7677 mW, 2100 MHz
acpicpu0: P3: FFH, lat   5 us, pow  6783 mW, 1900 MHz
acpicpu0: P4: FFH, lat   5 us, pow  3905 mW, 1400 MHz
acpicpu0: T0: I/O, lat   1 us, pow     0 mW, 100 %
acpicpu0: T1: I/O, lat   1 us, pow     0 mW,  88 %
acpicpu0: T2: I/O, lat   1 us, pow     0 mW,  76 %
acpicpu0: T3: I/O, lat   1 us, pow     0 mW,  64 %
acpicpu0: T4: I/O, lat   1 us, pow     0 mW,  52 %
acpicpu0: T5: I/O, lat   1 us, pow     0 mW,  40 %
acpicpu0: T6: I/O, lat   1 us, pow     0 mW,  28 %
acpicpu0: T7: I/O, lat   1 us, pow     0 mW,  16 %
acpicpu1 at cpu1: ACPI CPU
acpicpu2 at cpu2: ACPI CPU
acpicpu3 at cpu3: ACPI CPU
acpicpu4 at cpu4: ACPI CPU
acpicpu5 at cpu5: ACPI CPU
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
ERROR: 3657 cycle TSC drift observed
scsibus0: waiting 2 seconds for devices to settle...
IPsec: Initialized Security Association Processing.
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb2: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 6 ports with 6 removable, self powered
uhub2 at usb6: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 3 ports with 3 removable, self powered
uhub4 at usb3: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 3 ports with 3 removable, self powered
uhub5 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 6 ports with 6 removable, self powered
uhub6 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 3 ports with 3 removable, self powered
sd0 at scsibus0 target 0 lun 0: <SEAGATE, ST9146853SS, 0002> disk fixed
sd0: 136 GB, 107801 cyl, 2 head, 1329 sec, 512 bytes/sect x 286749488 sectors
sd0: tagged queueing
sd1 at scsibus0 target 1 lun 0: <SEAGATE, ST9146853SS, 0002> disk fixed
sd1: 136 GB, 107801 cyl, 2 head, 1329 sec, 512 bytes/sect x 286749488 sectors
sd1: tagged queueing
sd2 at scsibus0 target 4 lun 0: <SEAGATE, ST500NM0001, 0002> disk fixed
sd2: 465 GB, 249000 cyl, 2 head, 1961 sec, 512 bytes/sect x 976773168 sectors
sd2: tagged queueing
sd3 at scsibus0 target 6 lun 0: <SEAGATE, ST500NM0001, 0002> disk fixed
sd3: 465 GB, 249000 cyl, 2 head, 1961 sec, 512 bytes/sect x 976773168 sectors
sd3: tagged queueing
Kernelized RAIDframe activated
raid0: RAID Level 1
raid0: Components: /dev/sd0a /dev/sd1a
raid0: Total Sectors: 286719936 (139999 MB)
boot device: raid0
root on raid0a dumps on raid0b
root file system type: ffs
uhidev0 at uhub6 port 2 configuration 1 interface 0
uhidev0: Winbond Electronics Corp Hermon USB hidmouse Device, rev 1.10/0.01, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir
wsmouse0 at ums0 mux 0
uhidev1 at uhub6 port 2 configuration 1 interface 1
uhidev1: Winbond Electronics Corp Hermon USB hidmouse Device, rev 1.10/0.01, addr 2, iclass 3/1
ukbd0 at uhidev1
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
ipmi0: version 2.0 interface KCS iobase 0xca2/2 spacing 1
ipmi0: critical limit on 'Intrusion'
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

References:
- wm0 stopped receiving after mpt0 timeout recovery
  - From: Edgar Fuß
- Re: wm0 stopped receiving after mpt0 timeout recovery
  - From: Michael van Elst
- Re: wm0 stopped receiving after mpt0 timeout recovery
  - From: Edgar Fuß
- Re: wm0 stopped receiving after mpt0 timeout recovery
  - From: Masanobu SAITOH

Prev by Date: Re: Debugging an early kernel problem (more MIPS trouble)
Next by Date: Re: Debugging an early kernel problem (more MIPS trouble)
Previous by Thread: Re: wm0 stopped receiving after mpt0 timeout recovery
Next by Thread: wm0 stopped receiving without mpt0 timeout recovery
Indexes:

Home | Main Index | Thread Index | Old Index