Port-sparc64 archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

Re: bge fail on netboot of NetBSD-6 on v215 and v240

 Hi, all.

(2013/05/25 4:43), SAITOH Masanobu wrote:

Hi Erik.

(2013/05/25 2:06), Erik Fair wrote:


On May 24, 2013, at 04:51, SAITOH Masanobu <msaitoh%execsw.org@localhost> wrote:


This problem was fixed correctly in if_bge.c rev. 1.128. I tested with v210,
PowerMac G5_11 and i386.


Has this change been pulled up to netbsd-6?

        Erik <fair%netbsd.org@localhost>



Sorry, I fixed the panic problem I made, not the netboot problem.
I got SB2500 a few days ago and I heard that SB2500 has the same problem.
I'll try to fix the problem.

  Thanks.


  My SB2500 booted fine. Loaded ofwboot.net, loaded netbsd via bge0 and then 
mounted
the root file system using NFS.

Can anyone test with v215 and v240?



Sun Blade 2500, No Keyboard
Copyright 1998-2003 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.9.5, 2048 MB memory installed, Serial #55381183.
Ethernet address 0:3:ba:4d:c:bf, Host ID: 834d0cbf.



Rebooting with command: boot
Boot device: disk  File and args:
The file just loaded does not appear to be executable.
{0} ok boot net netbsd
Boot device: /pci@1c,600000/network@3  File and args: netbsd
1000 Mbps FDX Link up

NetBSD/sparc64 OpenFirmware Boot, Revision 1.16 (Fri May 17 00:08:17 UTC 2013)

1000 Mbps FDX Link up
Using BOOTP protocol:
 ip addr=192.168.1.36
  netmask=255.255.255.0
  gateway=192.168.1.1
  root addr=192.168.1.5
  path=/var/diskless/sparc64-current/root
1000 Mbps FDX Link up
Using BOOTP protocol:
 ip addr=192.168.1.36
  netmask=255.255.255.0
  gateway=192.168.1.1
  root addr=192.168.1.5
  path=/var/diskless/sparc64-current/root
=0xc96128
Loading netbsd: 8773904+614632+332520 [614544+404442]=0xde0900
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.99.20 (GENERIC) #4: Fri May 24 20:37:56 JST 2013
        
msaitoh%five.execsw.org@localhost:/disk/sources/4NetBSD-current/src/sys/arch/sparc64/compile/GENERIC
total memory = 2048 MB
avail memory = 1993 MB
mainbus0 (root): SUNW,Sun-Blade-2500 (Sun Blade 2500): hostid 834d0cbf
cpu0 at mainbus0: SUNW,UltraSPARC-IIIi @ 1280 MHz, UPA id 0
cpu0: system tick frequency 12 MHz
cpu0: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
cpu1 at mainbus0: SUNW,UltraSPARC-IIIi @ 1280 MHz, UPA id 1
cpu1: system tick frequency 12 MHz
cpu1: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
memory-controller at mainbus0 not configured
memory-controller at mainbus0 not configured
schizo0 at mainbus0: addr 4000e600000: "Tomatillo", version 0, ign 700, bus A 0 
to 0
schizo0:  pci0 at schizo0
bge0 at pci0 dev 3 function 0: Broadcom BCM5703 Gigabit Ethernet
Map control/status regs
pci_mem_find
pci_intr_map
pci_intr_string
pci_intr_establish
bge0: interrupting at ivec 371c
bge0: HW config 00000000, 00000000, 00000000, 00000000
(bge0: PCI 2.2 DMA setting)
bge0: ASIC BCM5702/5703 A2 (0x1002), Ethernet address 00:03:ba:4d:0c:bf
bus_dmamem_alloc
bus_dmamem_map
bus_dmamem_create
bus_dmamem_load
bzero
bge_jumbo_buf = 0x158a6a000
strcpy if_xname
mii setup
brgphy0 at bge0 phy 1: BCM5703 1000BASE-T media interface, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
if_attach
ether_ifattach
callout_init
Hardware Flags:
 - 5700 Family
 - Supports Jumbo Frames
 - No EEPROM
 - ADC bug
ppm at mainbus0 not configured
schizo1 at mainbus0: addr 4000ef00000: "Tomatillo", version 0, ign 740, bus B 0 
to 0
schizo1:  pci1 at schizo1
esiop0 at pci1 dev 4 function 0: Symbios Logic 53c1010-66 (ultra3-wide scsi)
esiop0: using on-board RAM
esiop0: interrupting at ivec 1f69
scsibus0 at esiop0: 16 targets, 8 luns per target
esiop1 at pci1 dev 4 function 1: Symbios Logic 53c1010-66 (ultra3-wide scsi)
esiop1: using on-board RAM
esiop1: interrupting at ivec 1f68
scsibus1 at esiop1: 16 targets, 8 luns per target
schizo2 at mainbus0: addr 4000f600000: "Tomatillo", version 0, ign 780, bus A 0 
to 1
schizo2:  pci2 at schizo2
ebus0 at pci2 dev 7 function 0
ebus0: Acer Labs M1533 PCI-ISA Bridge, revision 0x00
flashprom at ebus0 addr 0-fffff not configured
rtc0 at ebus0 addr 70-71: mc146818 compatible time-of-day clock: m5819p
pcfiic0 at ebus0 addr 320-321 ipl 2e
iic0 at pcfiic0: I2C bus
i2c-bridge at iic0 addr 0x09 not configured
gpio at iic0 addr 0x18 not configured
dbcool0 at iic0 addr 0x2c
dbcool0: ADM1031 dBCool(tm) Controller (rev 0x0083)
dbcool1 at iic0 addr 0x2e
dbcool1: ADM1031 dBCool(tm) Controller (rev 0x0083)
gpio at iic0 addr 0x37 not configured
gpio at iic0 addr 0x4e not configured
seeprom0 at iic0 addr 0x50: audio-card-fru-prom: size 8192
seeprom1 at iic0 addr 0x51: motherboard-fru-prom: size 8192
seeprom2 at iic0 addr 0x54: scsi-backplane-fru-prom: size 8192
spdmem0 at iic0 addr 0x5d
spdmem0: DDR SDRAM (registered), data ECC, 1GB, 286MHz (PC-2300)
spdmem1 at iic0 addr 0x5e
spdmem1: DDR SDRAM (registered), data ECC, 1GB, 286MHz (PC-2300)
clock-generator at iic0 addr 0x69 not configured
power at ebus0 addr 800-82f ipl 20 not configured
com0 at ebus0 addr 3f8-3ff ipl 2c: ns16550a, working fifo
com0: console
com1 at ebus0 addr 2e8-2ef ipl 2c: ns16550a, working fifo
dma at ebus0 addr 0-ffff not configured
alipm0 at pci2 dev 6 function 0: 223KHz clock
iic1 at alipm0: I2C bus
card-reader at iic1 addr 0x20 not configured
autri0 at pci2 dev 8 function 0: Acer Labs M5451 AC-Link Controller Audio 
Device (rev. 0x02)
autri0: interrupting at ivec 7a4
autri0: ac97: Analog Devices AD1881A codec; headphone, Analog Devices Phat 
Stereo
audio0 at autri0: full duplex, playback, capture, mmap, independent
midi0 at autri0: 4DWAVE MIDI UART
ohci0 at pci2 dev 10 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 
0x03)
ohci0: interrupting at ivec 7a7
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci2 dev 11 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 
0x03)
ohci1: interrupting at ivec 7a6
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
aceride0 at pci2 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 
0xc4)
aceride0: using ivec 1f98 for native-PCI interrupt
atabus0 at aceride0 channel 0
atabus1 at aceride0 channel 1
esiop2 at pci2 dev 2 function 0: Symbios Logic 53c875 (ultra-wide scsi)
esiop2: using on-board RAM
esiop2: interrupting at ivec 1f8c
scsibus2 at esiop2: 16 targets, 8 luns per target
ppb0 at pci2 dev 4 function 0: Texas Instruments product 0xac23 (rev. 0x02)
pci3 at ppb0 bus 1
ohci2 at pci3 dev 8 function 0: NEC USB Host Controller (rev. 0x43)
ohci2: interrupting at ivec 794
ohci2: OHCI version 1.0
usb2 at ohci2: USB revision 1.0
ohci3 at pci3 dev 8 function 1: NEC USB Host Controller (rev. 0x43)
ohci3: interrupting at ivec 795
ohci3: OHCI version 1.0
usb3 at ohci3: USB revision 1.0
ehci0 at pci3 dev 8 function 2: NEC USB2 Host Controller (rev. 0x04)
ehci0: interrupting at ivec 796
ehci0: companion controllers, 3 ports each: ohci2 ohci3
usb4 at ehci0: USB revision 2.0
fwohci0 at pci3 dev 11 function 0: Texas Instruments TSB43AA23 IEEE 1394 Host 
Controller (rev. 0x00)
fwohci0: interrupting at ivec 797
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:05:16:00:00:40:3a:85
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
ppm at mainbus0 not configured
schizo3 at mainbus0: addr 4000ff00000: "Tomatillo", version 0, ign 7c0, bus B 0 
to 0
schizo3:  pci4 at schizo3
wcfb0 at pci4 dev 2 function 0: 3D Labs WILDCAT 5110 (rev. 0x01)
i2c at mainbus0 not configured
pcons at mainbus0 not configured
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0
No counter-timer -- using %stick at 12MHz as system clock.
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
scsibus2: waiting 2 seconds for devices to settle...
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <JLMS XJ-HD166S, , D3S4> cdrom removable
uhub0 at usb0: Acer Labs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1 at usb2: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2 at usb1: Acer Labs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3 at usb3: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4 at usb4: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
sd0 at scsibus0 target 0 lun 0: <SEAGATE, ST336607LSUN36G, 0507> disk fixed
sd0: 34732 MB, 24622 cyl, 27 head, 107 sec, 512 bytes/sect x 71132959 sectors
sd0: sync (12.50ns offset 62), 16-bit (160.000MB/s) transfers, tagged queueing
sd1 at scsibus0 target 1 lun 0: <SEAGATE, ST336607LSUN36G, 0307> disk fixed
sd1: 34732 MB, 24622 cyl, 27 head, 107 sec, 512 bytes/sect x 71132959 sectors
sd1: sync (12.50ns offset 62), 16-bit (160.000MB/s) transfers, tagged queueing
rndattach: maxcpu = 32
root on bge0
nfs_boot: trying DHCP/BOOTP
(bge0: PCI 2.2 DMA setting)
nfs_boot: DHCP next-server: 192.168.1.5
nfs_boot: my_domain=execsw.org
nfs_boot: my_addr=192.168.1.36
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=192.168.1.1
root on 192.168.1.5:/var/diskless/sparc64-current/root
root file system type: nfs
#






--
-----------------------------------------------
                SAITOH Masanobu (msaitoh%execsw.org@localhost
                                 msaitoh%netbsd.org@localhost)
Home | Main Index | Thread Index | Old Index