Xorg on hp nc6120

[Riccardo Mottola <riccardo.mottola%libero.it@localhost>]

Hi,

I installed NetBSD 5.1 on an HP nc6120 laptop, I installed all the 
packages. The machine boots fine, but when I attempt to "startx" or to 
run "X -configure" the computer freezes. No X log gets written. Even 
attempting to start X from a remote console shows no error or warning, 
it freezes right after "List of video drivers:"

The laptop should have an intel GM chipset with shared memory.

Is this supported? What else can I try?

Thank you.
Riccardo

dmesg:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1 (GENERIC) #0: Sun Nov  7 14:39:56 UTC 2010

builds%b6.netbsd.org@localhost:/home/builds/ab/netbsd-5-1-RELEASE/i386/201011061943Z-obj/home/builds/ab/netbsd-5-1-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 503 MB
avail memory = 482 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Hewlett-Packard HP Compaq nc6120 (PY507ET#ABZ) (F.0B)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 1862MHz, id 0x6d8
cpu0: Enhanced SpeedStep (1308 mV) 1867 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 1867 1600 1333 
1067 800
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <HP    ,099C    ,16090520>, AslId <HP  ,00000001>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpiec0 at acpi0 (C004, PNP0C09): io 0x62,0x66
C1A2 (PNP0501) at acpi0 not configured
C1A7 (SMCF010) at acpi0 not configured
C1AF (PNP0401) at acpi0 not configured
npx1 at acpi0 (C1BE, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
attimer1 at acpi0 (C1BF, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (C1C0, PNP0800): io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
pckbc1 at acpi0 (C1C2, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (C1C3, SYN0112) (aux port): irq 12
acpibat0 at acpi0 (C174, PNP0C0A-1): ACPI Battery (Control Method)
acpibat0: battery info: Hewlett-Packard, LIon, Primary 19122 2005/10/25
acpibat1 at acpi0 (C173, PNP0C0A-2): ACPI Battery (Control Method)
acpiacad0 at acpi0 (C172, ACPI0003): ACPI AC Adapter
acpibut0 at acpi0 (C1E8, PNP0C0E): ACPI Sleep Button
acpilid0 at acpi0 (C1E9, PNP0C0D): ACPI Lid Switch
C1EF (PNP0C14) at acpi0 not configured
C248 (PNP0C0B) at acpi0 not configured
C249 (PNP0C0B) at acpi0 not configured
C24A (PNP0C0B) at acpi0 not configured
C24B (PNP0C0B) at acpi0 not configured
acpitz0 at acpi0 (TZ1): active cooling level 0: 75.0C active cooling 
level 1: 65.0C active cooling level 2: 55.0C active cooling level 3: 
45.0C critical 102.0C passive 52.0C
acpitz1 at acpi0 (TZ2): critical 103.0C, passive cooling
acpitz2 at acpi0 (TZ3): critical 102.0C passive 25.0C, passive cooling
acpitz3 at acpi0 (TZ4): critical 110.0C passive 64.0C, passive cooling
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pms0: Synaptics touchpad version 6.2
pms0: Palm detect, Multi-finger
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x2590 (rev. 0x03)
agp0 at pchb0: detected 7932k stolen memory
agp0: aperture at 0xc0000000, size 0x10000000
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x2592 (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
vendor 0x8086 product 0x2792 (miscellaneous display, revision 0x03) at 
pci0 dev 2 function 1 not configured
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x2660 (rev. 0x03)
ppb0: disabling notification events
pci1 at ppb0 bus 16
pci1: no spaces enabled!
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x2658 (rev. 0x03)
uhci0: interrupting at ioapic0 pin 23
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x2659 (rev. 0x03)
uhci1: interrupting at ioapic0 pin 17
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x265a (rev. 0x03)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x265b (rev. 0x03)
uhci3: interrupting at ioapic0 pin 19
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x265c (rev. 0x03)
ehci0: interrupting at ioapic0 pin 23
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb1 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xd3)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
iwi0 at pci2 dev 4 function 0: vendor 0x8086 product 0x4220 (rev. 0x05)
iwi0: interrupting at ioapic0 pin 21
iwi0: 802.11 address 00:15:00:38:b1:9e
iwi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
iwi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 
24Mbps 36Mbps 48Mbps 54Mbps
cbb0 at pci2 dev 6 function 0: vendor 0x104c product 0x8031 (rev. 0x00)
cbb1 at pci2 dev 6 function 1: vendor 0x104c product 0x8031 (rev. 0x00)
fwohci0 at pci2 dev 6 function 2: vendor 0x104c product 0x8032 (rev. 0x00)
fwohci0: interrupting at ioapic0 pin 22
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 71:8b:50:00:29:fd:4d:a6
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
vendor 0x104c product 0x8033 (miscellaneous mass storage) at pci2 dev 6 
function 3 not configured
sdhc0 at pci2 dev 6 function 4: vendor 0x104c product 0x8034 (rev. 0x00)
sdhc0: interrupting at ioapic0 pin 20
sdmmc0 at sdhc0
sdmmc1 at sdhc0
sdmmc2 at sdhc0
vendor 0x104c product 0x8035 (miscellaneous communications) at pci2 dev 
6 function 5 not configured
bge0 at pci2 dev 14 function 0: Broadcom BCM5705M Gigabit Ethernet
bge0: interrupting at ioapic0 pin 16
bge0: ASIC BCM5705 A3 (0x3003), Ethernet address 00:14:c2:d9:1f:f1
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5705 1000BASE-T media interface, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
cbb0: cacheline 0x10 lattimer 0x40
cbb0: bhlc 0x824010
cbb0: interrupting at ioapic0 pin 18
cardslot0 at cbb0
cardbus0 at cardslot0: bus 3
pcmcia0 at cardslot0
cbb1: cacheline 0x10 lattimer 0x40
cbb1: bhlc 0x824010
cbb1: interrupting at ioapic0 pin 19
cardslot1 at cbb1
cardbus1 at cardslot1: bus 4
pcmcia1 at cardslot1
auich0 at pci0 dev 30 function 2: i82801FB (ICH6) AC-97 Audio
auich0: interrupting at ioapic0 pin 21
auich0: ac97: Analog Devices AD1981B codec; headphone, 20 bit DAC, no 3D 
stereo
auich0: ac97: ext id 601<AC97_22,AMAP,VRA>
vendor 0x8086 product 0x266d (modem communications, revision 0x03) at 
pci0 dev 30 function 3 not configured
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x2641 (rev. 0x03)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801FB IDE Controller (ICH6) (rev. 0x03)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
isa0 at ichlpcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com2 at isa0 port 0x3e8-0x3ef irq 5: ns16550a, working fifo
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
acpiacad0: AC adapter online.
auich0: measured ac97 link rate at 47999 Hz, will use 48000 Hz
audio0 at auich0: full duplex, playback, capture, mmap, independent
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <HL-DT-ST DVD-RW GWA-4082N, F0CA6EB85EB8, 
CC15> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
wd0 at atabus0 drive 0: <HITACHI_DK23EA-30>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 28615 MB, 58140 cyl, 16 head, 63 sec, 512 bytes/sect x 58605120 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using 
DMA)
cd0(piixide0:0:1): using PIO mode 4, DMA mode 2 (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)