Re: netBSD 5.0 Bogus CIS

To: netbsd-users%NetBSD.org@localhost
Subject: Re: netBSD 5.0 Bogus CIS
From: Vlad Markov <markov%sdf.lonestar.org@localhost>
Date: Tue, 5 May 2009 01:34:39 +0000
On Tue, May 05, 2009 at 12:57:21AM +0000, Christos Zoulas wrote:
> In article <20090504235653.GA27322%SDF.LONESTAR.ORG@localhost>,
> Vlad Markov  <markov%sdf.lonestar.org@localhost> wrote:
> >My computer is a Thinkpad 600E.
> >
> >I run NetBSD 4.0.1 on a Thinkpad 600E now. During and after
> >an install of NetBSD 5.0, no matter which network card I
> >put into the PCMCIA slot, the console reported that the card
> >has a "bogus cis". These network cards work under NetBSD 4.01.
> >
> >Is there some way I can get the PCMCIA cards to work?
> 
> I think that the problem is that the pcmcia bridge is not powering
> up the cards right. What kind of a card you have? Do you have a before
> and after dmesg?
> 
> christos
 I hope by before/after dmesg you mean 4.0.1 and 5.0 dmeesg.

4.0.1 dmesg:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0.1 (GRUMPY 4.01) #4: Thu Nov 27 22:50:47 EST 2008
        root%grumpy.dwarf7.net@localhost:/usr/src/sys/arch/i386/compile/GRUMPY
total memory = 287 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 277 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfd820
PCI BIOS rev. 2.1 found at 0xfd880
pcibios: config mechanism [1][x], special cycles [1][x], last bus 7
PCI IRQ Routing Table rev. 1.0 found at 0xf9e20, size 112 bytes (5 entries)
PCI Interrupt Router at 000:07:0
PCI Exclusive IRQs: 11
------------------------------------------
  device vendor product pin PIRQ IRQ stage
------------------------------------------
000:02:0 0x104c 0xac1d   A  0x00  11  0    already assigned
000:02:1 0x104c 0xac1d   B  0x01  11  0    already assigned
000:06:0 0x1013 0x6001   A  0x00  11  0    already assigned
000:07:2 0x8086 0x7112   D  0x03  11  0    already assigned
001:00:0 0x10c8 0x0005   A  0x00  11  0    already assigned
------------------------------------------
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Mobile Pentium II (686-class), 363.98 MHz, id 0x66a
cpu0: features 183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR>
cpu0: features 183f9ff<PGE,MCA,CMOV,PAT,PSE36,MMX>
cpu0: features 183f9ff<FXSR>
cpu0: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu0: L2 cache 256 KB 32B/line 4-way
cpu0: ITLB 32 4 KB entries 4-way, 2 4 MB entries fully associative
cpu0: DTLB 64 4 KB entries 4-way, 8 4 MB entries 4-way
cpu0: 16 page colors
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <IBM   ,TP600R  ,00000001>, AslId <    ,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 24-bit timer
mpacpi: could not get bus number, assuming bus 0
LNKD: ACPI: Found matching pin for 0.7.INTD at func 2: 11
LNKA: ACPI: Found matching pin for 0.2.INTA at func 0: 11
LNKB: ACPI: Found matching pin for 0.2.INTB at func 1: 11
LNKA: ACPI: Found matching pin for 0.6.INTA at func 0: 9
LNKA: BIOS IRQ 9 for 0.6.INTA does not match previous BIOS IRQ 11
LNKA: ACPI: Found matching pin for 1.0.INTA at func 0: 11
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PNP0C0E): ACPI Sleep Button
PNP0C01 at acpi0 not configured
PNP0A03 at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
PNP0700 at acpi0 not configured
PNP0400 at acpi0 not configured
IBM0071 at acpi0 not configured
CSC0110 at acpi0 not configured
wss0 at acpi0 (CSC0100): NeoMagic 256AV audio
wss0: io 0x530-0x537,0x388-0x38b,0x220-0x233 irq 5 drq 1,0
wss0: CS4236B compatible
audio0 at wss0: full duplex, mmap
opl0 at wss0: model OPL3
midi0 at opl0: WSS Yamaha OPL3 (CPU-intensive output)
CSC0101 at acpi0 not configured
IBM3765 at acpi0 not configured
PNP0000 at acpi0 not configured
PNP0100 at acpi0 not configured
PNP0200 at acpi0 not configured
PNP0800 at acpi0 not configured
PNP0C02 at acpi0 not configured
PNP0C04 at acpi0 not configured
PNP0303 at acpi0 not configured
IBM3780 at acpi0 not configured
PNP0B00 at acpi0 not configured
acpiec0 at acpi0 (PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
acpibat0 at acpi0 (PNP0C0A-0): ACPI Battery (Control Method)
acpiacad0 at acpi0 (ACPI0003-0): ACPI AC Adapter
PNP0C0B at acpi0 not configured
PNP0C0B at acpi0 not configured
PNP0C0B at acpi0 not configured
PNP0C0B at acpi0 not configured
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: active cooling level 0: 90.0C
WARNING: Callback scheduled before sysmon task queue thread present.
acpitz0: critical 98.0C passive 47.8C
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
acpitz1 at acpi0: ACPI Thermal Zone
acpitz1: unable to get polling interval; using default of 30.0s
acpitz1: critical 63.0C
acpitz2 at acpi0: ACPI Thermal Zone
acpitz2: unable to get polling interval; using default of 30.0s
acpitz2: critical 60.0C
acpitz3 at acpi0: ACPI Thermal Zone
acpitz3: unable to get polling interval; using default of 30.0s
acpitz3: critical 57.0C
apm0 at acpi0: Power Management spec V1.2
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
WARNING: Callback scheduled before sysmon task queue thread present.
acpibat0: battery info: IBM Corporation , LION, ThinkPad Battery, 
acpiacad0: AC adapter online.
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x7190 (rev. 0x03)
agp0 at pchb0: aperture at 0x40000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x7191 (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: vendor 0x10c8 product 0x0005 (rev. 0x20)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
cbb0 at pci0 dev 2 function 0: vendor 0x104c product 0xac1d (rev. 0x00)
cbb1 at pci0 dev 2 function 1: vendor 0x104c product 0xac1d (rev. 0x00)
vendor 0x1013 product 0x6001 (audio multimedia, revision 0x01) at pci0 dev 6 
function 0 not configured
piixpcib0 at pci0 dev 7 function 0
piixpcib0: vendor 0x8086 product 0x7110 (rev. 0x02)
piixpcib0: SpeedStep SMI enabled
piixide0 at pci0 dev 7 function 1
piixide0: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
uhci0 at pci0 dev 7 function 2: vendor 0x8086 product 0x7112 (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
piixpm0 at pci0 dev 7 function 3: Power Management Controller
timecounter: Timecounter "piixpm0" frequency 3579545 Hz quality 900
piixpm0 24-bit timer
piixpm0: interrupting at SMI
iic0 at piixpm0: I2C bus
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2
pcmcia0 at cardslot0
cbb1: interrupting at irq 11
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 3
pcmcia1 at cardslot1
isa0 at piixpcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
pcppi0: children must have an explicit unit
midi1 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
WARNING: Callback scheduled before sysmon task queue thread present.
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
Kernelized RAIDframe activated
ath0 at cardbus0 function 0
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 
36Mbps 48Mbps 54Mbps
ath0: mac 7.9 phy 4.5 radio 5.6
wd0 at atabus0 drive 0: <IBM-DADA-25120>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 4887 MB, 10592 cyl, 15 head, 63 sec, 512 bytes/sect x 10009440 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <CRN-8241B, 1999/09/04, 1.22> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(piixide0:1:0): using PIO mode 4, DMA mode 2 (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
ath0: interrupting at 11
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x25, vt100 emulation)

---------------------------------------------------------------------------
netbsd 5.0 dmesg:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0 (GENERIC) #0: Sun Apr 26 18:50:08 UTC 2009
        
builds%b6.netbsd.org@localhost:/home/builds/ab/netbsd-5-0-RELEASE/i386/200904260229Z-obj/home/builds/ab/netbsd-5-0-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 223 MB
avail memory = 208 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
IBM 26455AU (Not Available)
mainbus0 (root)
cpu0 at mainbus0: Intel 686-class, 363MHz, id 0x66a
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <IBM   ,TP600R  ,00000001>, AslId <    ,00000000>
LNKA: ACPI: Found matching pin for 0.2.INTA at func 0: 11
LNKB: ACPI: Found matching pin for 0.2.INTB at func 1: 11
LNKA: ACPI: Found matching pin for 0.6.INTA at func 0: 9
LNKA: BIOS IRQ 9 for 0.6.INTA does not match previous BIOS IRQ 11
LNKA: ACPI: Found matching pin for 1.0.INTA at func 0: 11
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 24-bit timer
acpilid0 at acpi0 (LID0, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
FDC0 (PNP0700) at acpi0 not configured
UAR1 (PNP0501) at acpi0 not configured
LPT (PNP0400) at acpi0 not configured
attimer1 at acpi0 (TIMR, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (MPRC, PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
pckbc1 at acpi0 (KBD0, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (MOU0, IBM3780): aux port
pckbc2: irq 12
acpiec0 at acpi0 (EC0, PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
acpiec0: using global ACPI lock
acpibat0 at acpi0 (BAT0, PNP0C0A-0): ACPI Battery (Control Method)
acpibat0: battery info: IBM Corporation , LION, ThinkPad Battery 
acpiacad0 at acpi0 (AC, ACPI0003-0): ACPI AC Adapter
FN00 (PNP0C0B) at acpi0 not configured
FN20 (PNP0C0B) at acpi0 not configured
FN60 (PNP0C0B) at acpi0 not configured
FN70 (PNP0C0B) at acpi0 not configured
acpitz0 at acpi0 (THM0): active cooling level 0: 90.0C critical 98.0C passive 
37.8C
acpitz1 at acpi0 (THM2): active cooling level 0: 36.0C critical 63.0C
acpitz2 at acpi0 (THM6): active cooling level 0: 52.0C critical 60.0C
acpitz3 at acpi0 (THM7): active cooling level 0: 50.0C critical 57.0C
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x7190 (rev. 0x03)
agp0 at pchb0: aperture at 0x40000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x7191 (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: vendor 0x10c8 product 0x0005 (rev. 0x20)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
cbb0 at pci0 dev 2 function 0: vendor 0x104c product 0xac1d (rev. 0x00)
cbb1 at pci0 dev 2 function 1: vendor 0x104c product 0xac1d (rev. 0x00)
vendor 0x1013 product 0x6001 (audio multimedia, revision 0x01) at pci0 dev 6 
function 0 not configured
pcib0 at pci0 dev 7 function 0
pcib0: vendor 0x8086 product 0x7110 (rev. 0x02)
piixide0 at pci0 dev 7 function 1
piixide0: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
uhci0 at pci0 dev 7 function 2: vendor 0x8086 product 0x7112 (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
piixpm0 at pci0 dev 7 function 3
piixpm0: vendor 0x8086 product 0x7113 (rev. 0x02)
timecounter: Timecounter "piixpm0" frequency 3579545 Hz quality 900
piixpm0: 24-bit timer
piixpm0: interrupting at SMIpiixpm0: polling
iic0 at piixpm0: I2C bus
cbb0: cacheline 0x8 lattimer 0xa8
cbb0: bhlc 0x82a808
cbb0: interrupting at irq 11
cardslot0 at cbb0
cardbus0 at cardslot0: bus 2
pcmcia0 at cardslot0
cbb1: cacheline 0x8 lattimer 0xa8
cbb1: bhlc 0x82a808
cbb1: interrupting at irq 11
cardslot1 at cbb1
cardbus1 at cardslot1: bus 5
pcmcia1 at cardslot1
isa0 at pcib0
lpt2 at isa0 port 0x3bc-0x3bf irq : polled
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
sb0 at isa0 port 0x220-0x237 irq 5 drq 1: dsp v3.02
audio0 at sb0: half duplex, mmap, independent
midi1 at sb0: SB MIDI UART (CPU-intensive output)
opl0 at sb0: model OPL3
midi2 at opl0: SB Yamaha OPL3 (CPU-intensive output)
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
acpiacad0: AC adapter online.
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
wd0 at atabus0 drive 0: <HITACHI_DK239A-65B>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 6149 MB, 13328 cyl, 15 head, 63 sec, 512 bytes/sect x 12594960 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <TOSHIBA CD-ROM XM-1902B, , 1717> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(piixide0:1:0): using PIO mode 4, DMA mode 2 (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

------------------------------------------------------------------------------
Follow-Ups:
- Re: netBSD 5.0 Bogus CIS
  - From: Christos Zoulas
References:
- netBSD 5.0 Bogus CIS
  - From: Vlad Markov
- Re: netBSD 5.0 Bogus CIS
  - From: Christos Zoulas
Prev by Date: Re: netBSD 5.0 Bogus CIS
Next by Date: Re: perspective regarding documented problem in NetBSD 5.0
Previous by Thread: Re: netBSD 5.0 Bogus CIS
Next by Thread: Re: netBSD 5.0 Bogus CIS
Indexes:
Home | Main Index | Thread Index | Old Index