NetBSD 5.0 on Warp board

[David Wetzel <dave%turbocat.de@localhost>]

Hi,

I am using 5.0 on a PC Engines Warp board.
The ath0 gets many device timeouts and the RC4 was not very stable. (I  
had watchdog resets) Is this a known bug?
The fixups are needed for the board to make USB working. Is there  
something I have to change in my Kernel?

I use:

# PCI fixups, for both PCIBIOS and ACPI
options         PCI_ADDR_FIXUP          # fixup PCI I/O addresses
options         PCI_BUS_FIXUP           # fixup PCI bus numbering
options         PCI_INTR_FIXUP          # fixup PCI interrupt routing


Thanks!

David


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004,  
2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0 (WARP) #2: Thu Apr 30 03:41:19 CEST 2009
        dave@netbsd5:/usr/src/sys/arch/i386/compile/WARP
total memory = 127 MB
avail memory = 113 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Generic PC
PCI BIOS rev. 2.1 found at 0xfc47b
pcibios: config mechanism [1][x], special cycles [1][x], last bus 0
pcibios_get_intr_routing: function not supported
No PCI IRQ Routing information available.
mainbus0 (root)
pci_addr_fixup: 000:18:5 0x100b 0x0515 new address 0x08000000
pci_addr_fixup: 000:18:5 0x100b 0x0515 new address 0x08000040
pci_addr_fixup: 000:18:5 0x100b 0x0515 new address 0x08000080
pci_addr_fixup: 000:18:5 0x100b 0x0515 new address 0x080000c0
pci_addr_fixup: 000:18:5 0x100b 0x0515 new address 0x08000100
ACPI Error (tbxfroot-0308): A valid RSDP was not found [20080321]
ACPI: unable to initialize ACPI tables: AE_NOT_FOUND
cpu0 at mainbus0: NS/Cyrix 586-class, id 0x540
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1078 product 0x0001 (rev. 0x00)
ath0 at pci0 dev 13 function 0
ath0: interrupting at irq 12
ath0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps  
24Mbps 36Mbps 48Mbps 54Mbps
ath0: mac 10.5 phy 6.1 radio 6.3
sip0 at pci0 dev 14 function 0: NatSemi DP83815 10/100 Ethernet, rev 00
sip0: interrupting at irq 10
sip0: Ethernet address 00:0d:b9:06:53:00
nsphyter0 at sip0 phy 0: DP83815 10/100 media interface, rev. 1
nsphyter0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sip1 at pci0 dev 15 function 0: NatSemi DP83815 10/100 Ethernet, rev 00
sip1: interrupting at irq 9
sip1: Ethernet address 00:0d:b9:06:53:01
nsphyter1 at sip1 phy 0: DP83815 10/100 media interface, rev. 1
nsphyter1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sip2 at pci0 dev 16 function 0: NatSemi DP83815 10/100 Ethernet, rev 00
sip2: interrupting at irq 11
sip2: Ethernet address 00:0d:b9:06:53:02
nsphyter2 at sip2 phy 0: DP83815 10/100 media interface, rev. 1
nsphyter2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 18 function 0
pcib0: vendor 0x100b product 0x0510 (rev. 0x00)
vendor 0x100b product 0x0511 (miscellaneous bridge) at pci0 dev 18  
function 1 not configured
geodeide0 at pci0 dev 18 function 2
geodeide0: AMD Geode SC1100 IDE controller (rev. 0x01)
geodeide0: bus-master DMA support present
geodeide0: primary channel wired to compatibility mode
geodeide0: primary channel interrupting at irq 14
atabus0 at geodeide0 channel 0
geodeide0: secondary channel wired to compatibility mode
geodeide0: secondary channel interrupting at irq 15
atabus1 at geodeide0 channel 1
vendor 0x100b product 0x0503 (audio multimedia) at pci0 dev 18  
function 3 not configured
geodegcb0 at pci0 dev 18 function 5: AMD Geode GCB (rev. 0x03)
geodewdog0 at geodegcb0: AMD Geode SC1100 Watchdog Timer
geodecntr0 at geodegcb0: AMD Geode SC1100 27MHz Counter
timecounter: Timecounter "geodecounter" frequency 27000000 Hz quality  
1000
ohci0 at pci0 dev 19 function 0: vendor 0x0e11 product 0xa0f8 (rev.  
0x08)
ohci0: interrupting at irq 9
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
attimer0: attached to pcppi0
isapnp0: no ISA Plug 'n Play devices found
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: vendor 0x0e11 OHCI root hub, class 9/0, rev 1.00/1.00,  
addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at uhub0 port 3: vendor 0x0409 product 0x005a, class 9/0, rev  
2.00/1.00, addr 2
uhub1: 4 ports with 4 removable, self powered
uhmodem0 at uhub1 port 1 configuration 1 interface 0
uhmodem0: HUAWEI Technologies HUAWEI Mobile, rev 1.10/0.00, addr 3
ucom0 at uhmodem0 portno 0: modem
ucom1 at uhmodem0 portno 1: alt#1
umass0 at uhub1 port 1 configuration 1 interface 2
umass0: HUAWEI Technologies HUAWEI Mobile, rev 1.10/0.00, addr 3
umass0: using SCSI over Bulk-Only
umass0: could not read endpoint descriptor
wd0 at atabus0 drive 0: <SanDisk SDCFH2-002G>
wd0: drive supports 4-sector PIO transfers, LBA addressing
wd0: 1953 MB, 3970 cyl, 16 head, 63 sec, 512 bytes/sect x 4001760  
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2
wd0(geodeide0:0:0): using PIO mode 4, DMA mode 2 (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
ath0: setting keyix 0 w/o power
ath0: device timeout (txq 8, txintrperiod 1)
ath0: device timeout (txq 8, txintrperiod 1)
ath0: device timeout (txq 8, txintrperiod 1) <--- (there are lots of  
these)