NetBSD-Users archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: Bug in USB NetBSD 4.0? (Was: Filesystem problems and init.root)
Brendon Costa wrote:
> I have narrowed down the problem a bit more.
>
> The issue *may* have something to do with compressed vnd devices, or the
> drivers for accessing the serial port on a particular platform.
> Basically it works fine if i use a disk image that is not compressed
I may have narrowed it down to the USB device. Basically i can place the
USB device in a state such that any operations on /dev/sd0e produce an
"Input/output error" until i manually remove the USB stick from the USB
port and then re-insert it.
If after doing the vnconfig .... i cause the problem that generates a
"Input/output error" and then i go about manually cleaning up,
unmounting everything, un-configuring the vnd device but leaving the USB
stick mounted. If i then try and read from any of the files on the USB
sticks mounted dos filesystem, i get "Input/output errors" then too.
Then i unmount the USB dos filesystem: umount /mnt/flash
and try to mount it again: mount /dev/sd0e /mnt/flash
I get the error:
mount: cannot open '/dev/sd0e': Input/output error
Finally, if i remove the USB stick from the USB port and then re-insert
it. I can use it successfully again for a while.
There may be some pattern about the usage of the compressed vnd device
that causes this problem in the USB that i have not been able to
reproduce with a non-compressed image.
I have attached some logs that may be helpful from:
dmesg
config -x
usbdevs
Thanks,
Brendon.
addr 1: OHCI root hub, vendor 0x1022
addr 1: EHCI root hub, vendor 0x1022
addr 2: Cruzer Mini, SanDisk Corporation
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 4.0 (mprt) #0: Fri Sep 19 08:09:45 EST 2008
root@radiotest:/tmp/mprt-500-dlink/build_netbsd/nb-obj/sys/arch/i386/compile/mprt
total memory = 111 MB
rbus: rbus_min_start set to 0x20000000
avail memory = 102 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Calibrating TSC clock ... TSC clock: 333287920 Hz
BIOS32 rev. 0 found at 0xfd810
PCI BIOS rev. 2.1 found at 0xfd838
pcibios: config mechanism [1][x], special cycles [x][x], last bus 0
PCI BIOS has 2 Interrupt Routing table entries
PCI Exclusive IRQs: 9 10 11 12
pci_intr_fixup: no compatible PCI ICU found
Warning: unable to fix up PCI interrupt routing
mainbus0 (root)
pci_addr_fixup: 000:15:0 0x1022 0x2090 new address 0x00005800
ACPI Error (tbxfroot-0775): No valid RSDP was found [20060217]
ACPI Exception (tbxfroot-0531): AE_NOT_FOUND, RSDP structure not found -
Flags=8 [20060217]
ACPI Exception (tbxface-0162): AE_NO_ACPI_TABLES, Could not get the RSDP
[20060217]
ACPI Exception (tbxface-0211): AE_NO_ACPI_TABLES, Could not load tables
[20060217]
ACPI: unable to load tables: AE_NO_ACPI_TABLES
cpu0 at mainbus0: (uniprocessor)
cpu0: National Semiconductor Geode (586-class), 333.29 MHz, id 0x552
cpu0: features 80a93d<FPU,DE,PSE,TSC,MSR,CX8,SEP>
cpu0: features 80a93d<PGE,CMOV,MMX>
cpu0: "Geode(TM) Integrated Processor by National Semi"
cpu0: I-cache 16 KB 32B/line 4-way, D-cache 16 KB 32B/line 4-way
cpu0: ITLB 8 4 KB entries fully associative
cpu0: DTLB 8 4 KB entries fully associative
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 1 function 0
pchb0: vendor 0x100b product 0x0028 (rev. 0x21)
vga1 at pci0 dev 1 function 1: vendor 0x100b product 0x0030 (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
wsdisplay0: screen 1-3 added (80x25, vt100 emulation)
vendor 0x1283 product 0x8888 (miscellaneous bridge, revision 0x03) at pci0 dev
6 function 0 not configured
rtk0 at pci0 dev 7 function 0: Realtek 8139 10/100BaseTX (rev. 0x10)
rtk0: interrupting at irq 10
rtk0: Ethernet address 00:e0:c7:07:f3:9a
rlphy0 at rtk0 phy 7: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 15 function 0
pcib0: vendor 0x1022 product 0x2090 (rev. 0x03)
viaide0 at pci0 dev 15 function 2
viaide0: Advanced Micro Devices CS5536 IDE Controller (rev. 0x01)
viaide0: bus-master DMA support present
viaide0: primary channel wired to compatibility mode
viaide0: primary channel ignored (disabled)
viaide0: secondary channel wired to compatibility mode
viaide0: secondary channel ignored (disabled)
vendor 0x1022 product 0x2093 (audio multimedia, revision 0x01) at pci0 dev 15
function 3 not configured
ohci0 at pci0 dev 15 function 4: vendor 0x1022 product 0x2094 (rev. 0x02)
ohci0: interrupting at irq 9
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x1022 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ehci0 at pci0 dev 15 function 5: vendor 0x1022 product 0x2095 (rev. 0x02)
ehci0: interrupting at irq 9
ehci0: EHCI version 1.0
ehci0: companion controller, 4 ports each: ohci0
usb1 at ehci0: USB revision 2.0
uhub1 at usb1
uhub1: vendor 0x1022 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 4 ports with 4 removable, self powered
vendor 0x1022 product 0x2096 (USB serial bus, interface 0xfe, revision 0x02) at
pci0 dev 15 function 6 not configured
vendor 0x1022 product 0x2097 (USB serial bus, interface 0x80, revision 0x02) at
pci0 dev 15 function 7 not configured
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsprobe: reset error 5
attimer0 at isa0 port 0x40-0x43: AT Timer
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
atabus0 at wdc0 channel 0
pcppi0 at isa0 port 0x61
pcppi0: children must have an explicit unit
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
timecounter: Timecounter "TSC" frequency 333287920 Hz quality 800
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
wd0 at atabus0 drive 0: <PQI IDE DiskOnModule>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 495 MB, 1007 cyl, 16 head, 63 sec, 512 bytes/sect x 1015056 sectors
wd0: drive supports PIO mode 4, DMA mode 0, Ultra-DMA mode 2 (Ultra/33)
boot device: wd0
root on wd0a dumps on wd0b
mountroot: trying ffs...
root file system type: ffs
WARNING: clock lost 728 days
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
warning: no /dev/console
init: copying out path `/sbin/init' 11
/dev/wd0a: file system not clean (fs_clean=4); please fsck(8)
/dev/wd0a: lost blocks 0 files 0
/dev/wd0a: file system not clean (fs_clean=4); please fsck(8)
/dev/wd0a: lost blocks 0 files 0
/dev/wd0e: file system not clean (fs_clean=4); please fsck(8)
/dev/wd0e: lost blocks 0 files 0
umass0 at uhub1 port 1 configuration 1 interface 0
umass0: vendor 0x0781 Cruzer Mini, rev 2.00/0.26, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <Generic, STORAGE DEVICE, 0026> disk removable
sd0: fabricating a geometry
sd0: 125 MB, 125 cyl, 64 head, 32 sec, 512 bytes/sect x 256000 sectors
sd0: fabricating a geometry
### START CONFIG FILE
"/tmp/mprt-500-dlink/build_netbsd/usr/src/sys/arch/i386/conf/mprt"
# $NetBSD: GENERIC,v 1.799.2.15 2007/11/26 21:35:47 xtraeme Exp $
#
# GENERIC machine description file
#
# This machine description file is used to generate the default NetBSD
# kernel. The generic kernel does not include all options, subsystems
# and device drivers, but should be useful for most applications.
#
# The machine description file can be customised for your specific
# machine to reduce the kernel size and improve its performance.
#
# For further information on compiling NetBSD kernels, see the config(8)
# man page.
#
# For further information on hardware support for this architecture, see
# the intro(4) man page. For further information about kernel options
# for this architecture, see the options(4) man page. For an explanation
# of each device driver in this file see the section 4 man page for the
# device.
include "arch/i386/conf/std.i386"
options INCLUDE_CONFIG_FILE # embed config file in kernel binary
#ident "GENERIC-$Revision: 1.799.2.15 $"
maxusers 2 # estimated number of users
# CPU support. At least one is REQUIRED.
#options I386_CPU
#options I486_CPU
options I586_CPU
#options I686_CPU
makeoptions CPUFLAGS="-march=i486 -mtune=pentiumpro" # Assume at least 486,
# tune for more modern
# CPU-related options.
#options MATH_EMULATE # floating point emulation
#options VM86 # virtual 8086 emulation
#options USER_LDT # user-settable LDT; used by WINE
# insert delay no-ops in interrupts; recommended on very old machines
#options PIC_DELAY
# Enhanced SpeedStep Technology in the Pentium M
#options ENHANCED_SPEEDSTEP
#options EST_FREQ_USERWRITE # any user can set frequency
# AMD PowerNow! K7
#options POWERNOW_K7
# AMD PowerNow! and Cool`n'Quiet technology
#options POWERNOW_K8
options MTRR # memory-type range register syscall support
# doesn't work with MP just yet..
#options PERFCTRS # performance-monitoring counters support
options MULTIBOOT # Multiboot support (see multiboot(8))
# delay between "rebooting ..." message and hardware reset, in milliseconds
#options CPURESET_DELAY=2000
# This option allows you to force a serial console at the specified
# I/O address. see console(4) for details.
#options CONSDEVNAME="\"com\"",CONADDR=0x2f8,CONSPEED=57600
# you don't want the option below ON iff you are using the
# serial console option of the new boot strap code.
#options CONS_OVERRIDE # Always use above! independent of boot info
# The following options override the memory sizes passed in from the boot
# block. Use them *only* if the boot block is unable to determine the correct
# values. Note that the BIOS may *correctly* report less than 640k of base
# memory if the extended BIOS data area is located at the top of base memory
# (as is the case on most recent systems).
#options REALBASEMEM=639 # size of base memory (in KB)
#options REALEXTMEM=15360 # size of extended memory (in KB)
# Standard system options
options INSECURE # disable kernel security levels - X needs this
options RTC_OFFSET=0 # hardware clock is this many mins. west of GMT
options NTP # NTP phase/frequency locked loop
#options NO_TSC_TIME # Don't use TSC microtime, even if available.
# Improves time behavior under VMware.
options KTRACE # system call tracing via ktrace(1)
# @@@Brendon Enabled in 3.1 generic
#options SYSTRACE # system call vetting via systrace(1)
options SYSVMSG # System V-like message queues
options SYSVSEM # System V-like semaphores
#options SEMMNI=10 # number of semaphore identifiers
#options SEMMNS=60 # number of semaphores in system
#options SEMUME=10 # max number of undo entries per process
#options SEMMNU=30 # number of undo structures in system
options SYSVSHM # System V-like memory sharing
#options SHMMAXPGS=2048 # 2048 pages is the default
options P1003_1B_SEMAPHORE # p1003.1b semaphore support
options LKM # loadable kernel modules
options USERCONF # userconf(4) support
#options PIPE_SOCKETPAIR # smaller, but slower pipe(2)
options SYSCTL_INCLUDE_DESCR # Include sysctl descriptions in kernel
# Beep when it is safe to power down the system (requires sysbeep)
#options BEEP_ONHALT
# Some tunable details of the above feature (default values used below)
#options BEEP_ONHALT_COUNT=3 # Times to beep
#options BEEP_ONHALT_PITCH=1500 # Default frequency (in Hz)
#options BEEP_ONHALT_PERIOD=250 # Default duration (in msecs)
# Enable experimental buffer queue strategy for better responsiveness under
# high disk I/O load. Likely stable but not yet the default.
#options BUFQ_READPRIO
#options BUFQ_PRIOCSCAN
# Diagnostic/debugging support options
options DIAGNOSTIC # expensive kernel consistency checks
options DEBUG # expensive debugging checks/support
#options KMEMSTATS # kernel memory statistics (vmstat -m)
# @@@Brendon Do we want to get rid of this?
options DDB # in-kernel debugger
options DDB_ONPANIC=0 # see also sysctl(8): `ddb.onpanic'
options DDB_HISTORY_SIZE=512 # enable history editing in DDB
#options KGDB # remote debugger
#options KGDB_DEVNAME="\"com\"",KGDB_DEVADDR=0x3f8,KGDB_DEVRATE=9600
#makeoptions DEBUG="-g" # compile full symbol table
# Compatibility options
#options COMPAT_NOMID # NetBSD 0.8, 386BSD, and BSDI
#options COMPAT_09 # NetBSD 0.9
#options COMPAT_10 # NetBSD 1.0
#options COMPAT_11 # NetBSD 1.1
#options COMPAT_12 # NetBSD 1.2, 386BSD, and BSDI
#options COMPAT_13 # NetBSD 1.3, 386BSD, and BSDI
#options COMPAT_14 # NetBSD 1.4
#options COMPAT_15 # NetBSD 1.5
#options COMPAT_16 # NetBSD 1.6
#options COMPAT_20 # NetBSD 2.0
#options COMPAT_30 # NetBSD 3.0
#options COMPAT_43 # 4.3BSD, 386BSD, and BSDI
#options COMPAT_386BSD_MBRPART # recognize old partition ID
#options TCP_COMPAT_42 # 4.2BSD TCP/IP bug compat. Not recommended.
#options COMPAT_OSSAUDIO # OSS (Voxware) audio driver compatibility
#options COMPAT_SVR4 # binary compatibility with SVR4
#options COMPAT_IBCS2 # binary compatibility with SCO and ISC
#options COMPAT_LINUX # binary compatibility with Linux
#options COMPAT_FREEBSD # binary compatibility with FreeBSD
#options COMPAT_MACH # binary compatibility with Mach binaries
#options COMPAT_DARWIN # binary compatibility with Darwin binaries
#options EXEC_MACHO # exec MACH-O binaries
#options COMPAT_NDIS # NDIS network driver
#options COMPAT_PECOFF # kernel support to run Win32 apps
options COMPAT_BSDPTY # /dev/[pt]ty?? ptys.
# File systems
file-system FFS # UFS
#file-system EXT2FS # second extended file system (linux)
#file-system LFS # log-structured file system
file-system MFS # memory file system
#file-system NFS # Network File System client
file-system NTFS # Windows/NT file system (experimental)
#file-system CD9660 # ISO 9660 + Rock Ridge file system
file-system MSDOSFS # MS-DOS file system
#file-system FDESC # /dev/fd
#file-system KERNFS # /kern
file-system NULLFS # loopback file system
file-system OVERLAY # overlay file system
#file-system PORTAL # portal filesystem (still experimental)
#file-system PROCFS # /proc
file-system UMAPFS # NULLFS + uid and gid remapping
file-system UNION # union file system
#file-system CODA # Coda File System; also needs vcoda (below)
#file-system SMBFS # experimental - CIFS; also needs nsmb (below)
file-system PTYFS # /dev/ptm support
file-system TMPFS # Efficient memory file-system
#file-system UDF # experimental - OSTA UDF CD/DVD file-system
# File system options
#options QUOTA # UFS quotas
#options FFS_EI # FFS Endian Independent support
options SOFTDEP # FFS soft updates support.
# Note that UFS_DIRHASH is suspected of causing kernel memory corruption.
# It is not recommended for general use.
#options UFS_DIRHASH # UFS Large Directory Hashing - Experimental
#options NFSSERVER # Network File System server
#options FFS_NO_SNAPSHOT # No FFS snapshot support
#options EXT2FS_SYSTEM_FLAGS # makes ext2fs file flags (append and
# immutable) behave as system flags.
# Networking options
#options GATEWAY # packet forwarding
options INET # IP + ICMP + TCP + UDP
options INET6 # IPV6
#options IPSEC # IP security
#options IPSEC_ESP # IP security (encryption part; define w/IPSEC)
#options IPSEC_NAT_T # IPsec NAT traversal (NAT-T)
#options IPSEC_DEBUG # debug for IP security
#options MROUTING # IP multicast routing
#options PIM # Protocol Independent Multicast
#options ISO,TPIP # OSI
#options EON # OSI tunneling over IP
#options NETATALK # AppleTalk networking protocols
#options PPP_BSDCOMP # BSD-Compress compression support for PPP
#options PPP_DEFLATE # Deflate compression support for PPP
#options PPP_FILTER # Active filter support for PPP (requires bpf)
#options PFIL_HOOKS # pfil(9) packet filter hooks
#options IPFILTER_LOG # ipmon(8) log support
#options IPFILTER_LOOKUP # ippool(8) support
#options IPFILTER_DEFAULT_BLOCK # block all packets by default
#options TCP_DEBUG # Record last TCP_NDEBUG packets with SO_DEBUG
#options ALTQ # Manipulate network interfaces' output queues
#options ALTQ_BLUE # Stochastic Fair Blue
#options ALTQ_CBQ # Class-Based Queueing
#options ALTQ_CDNR # Diffserv Traffic Conditioner
#options ALTQ_FIFOQ # First-In First-Out Queue
#options ALTQ_FLOWVALVE # RED/flow-valve (red-penalty-box)
#options ALTQ_HFSC # Hierarchical Fair Service Curve
#options ALTQ_LOCALQ # Local queueing discipline
#options ALTQ_PRIQ # Priority Queueing
#options ALTQ_RED # Random Early Detection
#options ALTQ_RIO # RED with IN/OUT
#options ALTQ_WFQ # Weighted Fair Queueing
# These options enable verbose messages for several subsystems.
# Warning, these may compile large string tables into the kernel!
#options ACPIVERBOSE # verbose ACPI device autoconfig messages
#options EISAVERBOSE # verbose EISA device autoconfig messages
#options MIIVERBOSE # verbose PHY autoconfig messages
#options PCIVERBOSE # verbose PCI device autoconfig messages
#options PCI_CONFIG_DUMP # verbosely dump PCI config space
#options PCMCIAVERBOSE # verbose PCMCIA configuration messages
#options SCSIVERBOSE # human readable SCSI error messages
#options USBVERBOSE # verbose USB device autoconfig messages
#options PNPBIOSVERBOSE # verbose PnP BIOS messages
#options PNPBIOSDEBUG # more fulsome PnP BIOS debugging messages
#options I2OVERBOSE # verbose I2O driver messages
#options MCAVERBOSE # verbose MCA device autoconfig messages
#options NFS_BOOT_DHCP,NFS_BOOT_BOOTPARAM
#
# wscons options
#
# builtin terminal emulations
#options WSEMUL_SUN # sun terminal emulation
options WSEMUL_VT100 # VT100 / VT220 emulation
# customization of console and kernel output - see dev/wscons/wsdisplayvar.h
options WSDISPLAY_CUSTOM_OUTPUT # color customization from wsconsctl(8)
#options WS_DEFAULT_FG=WSCOL_WHITE
#options WS_DEFAULT_BG=WSCOL_BLACK
#options WS_DEFAULT_COLATTR="(0)"
#options WS_DEFAULT_MONOATTR="(0)"
options WS_KERNEL_FG=WSCOL_GREEN
#options WS_KERNEL_BG=WSCOL_BLACK
#options WS_KERNEL_COLATTR=""
#options WS_KERNEL_MONOATTR=""
# customization of console border color
options WSDISPLAY_CUSTOM_BORDER # custom border colors via wsconsctl(8)
#options WSDISPLAY_BORDER_COLOR=WSCOL_BLUE # default color
# compatibility to other console drivers
options WSDISPLAY_COMPAT_PCVT # emulate some ioctls
options WSDISPLAY_COMPAT_SYSCONS # emulate some ioctls
options WSDISPLAY_COMPAT_USL # VT handling
options WSDISPLAY_COMPAT_RAWKBD # can get raw scancodes
#options WSKBD_EVENT_AUTOREPEAT # auto repeat in event mode
#options WSKBD_USONLY # strip off non-US keymaps
# don't attach pckbd as the console if no PS/2 keyboard is found
options PCKBD_CNATTACH_MAY_FAIL
# see dev/pckbport/wskbdmap_mfii.c for implemented layouts
#options PCKBD_LAYOUT="(KB_DE | KB_NODEAD)" # for pckbd driver
#options UKBD_LAYOUT="(KB_DE | KB_NODEAD)" # for ukbd driver
# allocate a number of virtual screens at autoconfiguration time
options WSDISPLAY_DEFAULTSCREENS=4
# use a large software cursor that doesn't blink
options PCDISPLAY_SOFTCURSOR
# modify the screen type of the console; defaults to "80x25"
#options VGA_CONSOLE_SCREENTYPE="\"80x24\""
# work around a hardware bug that loaded fonts don't work; found on ATI cards
#options VGA_CONSOLE_ATI_BROKEN_FONTSEL
# console scrolling support.
options WSDISPLAY_SCROLLSUPPORT
# enable VGA raster mode capable of displaying multilingual text on console
#options VGA_RASTERCONSOLE
# enable splash screen support; requires hw driver support
#options SPLASHSCREEN
#options SPLASHSCREEN_PROGRESS
# Kernel root file system and dump configuration.
config netbsd root on ? type ?
#config netbsd root on sd0a type ffs
#config netbsd root on ? type nfs
#
# Device configuration
#
mainbus0 at root
cpu* at mainbus?
ioapic* at mainbus?
# Doesn't do anything yet.
#p64h2apic* at pci? dev? function? # P64H2 IOxAPIC
#apm0 at mainbus0 # Advanced power management
# Tuning for power management, see apm(4) for more details.
#options APM_NO_IDLE # Don't call BIOS CPU idle function
#options APM_V10_ONLY # Use only the APM 1.0 calls
#options APM_NO_POWEROFF # Don't power off on halt(8)
#options APM_POWER_PRINT # Print stats on the console
#options APM_DISABLE_INTERRUPTS=0 # Don't disable interrupts
# Basic Bus Support
#IPMI support
#ipmi0 at mainbus?
# Advanced Configuration and Power Interface
# This option can be used to retrieve CPU and APIC information.
# that I/O APICs can be used if ACPI is enabled below.
# To use the I/O APIC(s), enable the ioapic line above.
#options MPBIOS # configure CPUs and APICs using MPBIOS
#options MPBIOS_SCANPCI # find PCI roots using MPBIOS
options ACPI_SCANPCI # find PCI roots using ACPI
acpi0 at mainbus0
#options ACPI_ACTIVATE_DEV # If set, activate inactive devices
#options ACPICA_PEDANTIC # force strict conformance to the Spec.
# ACPI devices
acpiacad* at acpi? # ACPI AC Adapter
acpibat* at acpi? # ACPI Battery
acpibut* at acpi? # ACPI Button
acpiec* at acpi? # ACPI Embedded Controller
acpilid* at acpi? # ACPI Lid Switch
acpitz* at acpi? # ACPI Thermal Zone
# Mainboard devices
attimer* at acpi? # AT Timer
#com* at acpi? # Serial communications interface
#fdc* at acpi? # Floppy disk controller
joy* at acpi? # Joystick/Game port
#lpt* at acpi? # Parallel port
mpu* at acpi? # Roland MPU-401 MIDI UART
npx* at acpi? # Math coprocessor
pckbc* at acpi? # PC keyboard controller
pcppi* at acpi? # AT-style speaker sound
#ug* at acpi? # Abit uGuru Hardware Monitor
wss* at acpi? # NeoMagic 256AV in wss mode
ym* at acpi? # Yamaha OPL3-SA[23] audio
# Sony Vaio jog dial
spic* at acpi? # Sony Programmable I/O Controller
wsmouse* at spic?
# Sony LCD brightness etc.
sony* at acpi? # Sony Miscellaneous Controller
# Toshiba Libretto devices
vald* at acpi?
# Plug-and-Play BIOS and attached devices
#pnpbios* at mainbus?
# mainboard audio chips
#ess* at pnpbios? index ? # ESS AudioDrive
#sb* at pnpbios? index ? # NeoMagic 256AV in sb mode
#wss* at pnpbios? index ? # NeoMagic 256AV in wss mode
#ym* at pnpbios? index ? # Yamaha OPL3-SA[23] audio
# com port
# If enabled, consider changing "com0", "com1", and "com2" under "ISA Serial
# Interfaces" to "com*", otherwise com2 will attach at pnpbios? and there
# will be no com0. A side effect is pcmcia (and other) com? previously
# starting at com3 may attach as com1 or com2.
#com* at pnpbios? index ? # serial ports
# parallel port
# The above "com*" comments apply, cf. "lpt0" under "ISA parallel
# "printer interfaces".
#lpt* at pnpbios? index ? # parallel ports
#pckbc* at pnpbios? index ? # PC keyboard/mouse controller
#fdc* at pnpbios? index ? # floppy controller
#npx* at pnpbios? index ? # Math coprocessor
# IDE controller on Toshiba Portege 3000 series (crippled PCI device)
#pciide* at pnpbios? index ?
# PCI bus support
pci* at mainbus? bus ?
pci* at pchb? bus ?
pci* at ppb? bus ?
# Configure PCI using BIOS information
options PCIBIOS # PCI BIOS support
options PCIBIOSVERBOSE # PCI BIOS verbose info
options PCIBIOS_IRQS_HINT=0x0a00 # PCI interrupts hint. IRQ 9 or 11
#options PCIBIOS_INTR_GUESS # see pcibios(4)
#options PCIBIOS_LIBRETTO_FIXUP # this code makes the Toshiba Libretto
# L2/L3 work, but should not be enabled
# on anything else.
#options PCIBIOS_SHARP_MM20_FIXUP # this code makes the Sharp MM 20
# work, but should not be enabled
# on anything else.
#options PCIINTR_DEBUG # super-verbose PCI interrupt fixup
# PCI fixups, for both PCIBIOS and ACPI
options PCI_ADDR_FIXUP # fixup PCI I/O addresses
options PCI_BUS_FIXUP # fixup PCI bus numbering
options PCI_INTR_FIXUP # fixup PCI interrupt routing
# System Controllers
elansc* at pci? dev ? function ? # AMD Elan SC520 System Controller
gpio* at elansc?
# PCI bridges
#ichlpcib* at pci? dev ? function ? # Intel ICH PCI-ISA w/ watchdog and
# SpeedStep support
piixpcib* at pci? dev ? function ? # Intel PIIX4 PCI-ISA w/ SpeedStep
#gscpcib* at pci? dev ? function ? # NS Geode PCI-ISA w/ GPIO support
#viapcib* at pci? dev ? function ? # VIA VT8235 PCI-ISA w/ SMBus support
#iic* at viapcib?
pchb* at pci? dev ? function ? # PCI-Host bridges
pceb* at pci? dev ? function ? # PCI-EISA bridges
pcib* at pci? dev ? function ? # PCI-ISA bridges
pcmb* at pci? dev ? function ? # PCI-MCA bridges
ppb* at pci? dev ? function ? # PCI-PCI bridges
# XXX 'puc's aren't really bridges, but there's no better place for them here
puc* at pci? dev ? function ? # PCI "universal" comm. cards
agp* at pchb?
# EISA bus support
eisa0 at mainbus?
eisa0 at pceb?
# ISA bus support
#isa0 at ichlpcib?
isa0 at piixpcib?
#isa0 at gscpcib?
#isa0 at viapcib?
isa0 at mainbus?
isa0 at pceb?
isa0 at pcib?
# PCMCIA bus support
pcmcia* at pcic? controller ? socket ?
pcmcia* at tcic? controller ? socket ?
# MCA bus support
mca0 at mainbus?
# ISA PCMCIA controllers
pcic0 at isa? port 0x3e0 iomem 0xd0000 iosiz 0x10000
pcic1 at isa? port 0x3e2 iomem 0xe0000 iosiz 0x4000
pcic2 at isa? port 0x3e4 iomem 0xe0000 iosiz 0x4000
tcic0 at isa? port 0x240 iomem 0xd0000 iosiz 0x10000
# PCI PCMCIA controllers
pcic0 at pci? dev? function ?
# ISA Plug-and-Play bus support
isapnp0 at isa?
# ISA Plug-and-Play PCMCIA controllers
pcic* at isapnp?
# CardBus bridge support
cbb* at pci? dev ? function ?
cardslot* at cbb?
# CardBus bus support
cardbus* at cardslot?
pcmcia* at cardslot?
# Coprocessor Support
# Math Coprocessor support
npx0 at isa? port 0xf0 irq 13 # x86 math coprocessor
# Console Devices
# ISA console
#pc0 at isa? port 0x60 irq 1 # pccons generic PC console driver
# Keyboard layout configuration for pccons
#options FRENCH_KBD
#options FINNISH_KBD
#options GERMAN_KBD
#options NORWEGIAN_KBD
# wscons
pckbc0 at isa? # pc keyboard controller
pckbd* at pckbc? # PC keyboard
pms* at pckbc? # PS/2 mouse for wsmouse
#options PMS_DISABLE_POWERHOOK # Disable PS/2 reset on resume
#options PMS_SYNAPTICS_TOUCHPAD # Enable support for Synaptics Touchpads
vga0 at isa?
vga* at pci? dev ? function ?
pcdisplay0 at isa? # CGA, MDA, EGA, HGA
#machfb* at pci? dev ? function ? # ATI Mach64 framebuffer driver
wsdisplay* at vga? console ?
wsdisplay* at pcdisplay? console ?
#wsdisplay* at machfb? console ?
wskbd* at pckbd? console ?
wsmouse* at pms? mux 0
# VESA framebuffer console
#options KVM86 # required for vesabios
#vesabios* at vesabiosbus?
#vesafb* at vesabios?
#options VESAFB_WIDTH=640
#options VESAFB_HEIGHT=480
#options VESAFB_DEPTH=8
#options VESAFB_PM # power management support
#wsdisplay* at vesafb? console ?
attimer0 at isa?
pcppi0 at isa?
sysbeep0 at pcppi?
# Serial Devices
# PCI serial interfaces
com* at puc? port ? # 16x50s on "universal" comm boards
cy* at pci? dev ? function ? # Cyclades Cyclom-Y serial boards
cz* at pci? dev ? function ? # Cyclades-Z multi-port serial boards
# ISA Plug-and-Play serial interfaces
com* at isapnp? # Modems and serial boards
# PCMCIA serial interfaces
com* at pcmcia? function ? # Modems and serial cards
pcmcom* at pcmcia? function ? # PCMCIA multi-port serial cards
com* at pcmcom? slave ? # ...and the slave devices
# CardBus serial interfaces
#com* at cardbus? function ? # Modems and serial cards
# ISA serial interfaces
#options COM_HAYESP # adds Hayes ESP serial board support
com0 at isa? port 0x3f8 irq 4 # Standard PC serial ports
com1 at isa? port 0x2f8 irq 3
com2 at isa? port 0x3e8 irq 5
#com3 at isa? port 0x2e8 irq 9
#ast0 at isa? port 0x1a0 irq 5 # AST 4-port serial cards
#com* at ast? slave ?
#boca0 at isa? port 0x100 irq 5 # BOCA 8-port serial cards
#boca0 at isa? port 0x100 irq 5 # BOCA 16-port serial cards (BB2016)
#boca1 at isa? port 0x140 irq 5 # this line is also needed for BB2016
#com* at boca? slave ?
#tcom0 at isa? port 0x100 irq 7 # TC-800 8-port serial cards
#com* at tcom? slave ?
#rtfps0 at isa? port 0x1230 irq 10 # RT 4-port serial cards
#com* at rtfps? slave ?
#cy0 at isa? iomem 0xd4000 irq 12 # Cyclades serial cards
#addcom0 at isa? port 0x108 irq 5 # Addonics FlexPort 8S
#com* at addcom? slave ?
#moxa0 at isa? port 0x100 irq 5 # MOXA C168H serial card (experimental)
#com* at moxa? slave ?
#ioat* at isa? port 0x220 irq 5 # BOCA IOAT66 6-port serial card
#com* at ioat? slave ?
# MCA serial interfaces
com* at mca? slot ? # 16x50s on comm boards
# Parallel Printer Interfaces
# PCI parallel printer interfaces
lpt* at puc? port ? # || ports on "universal" comm boards
# ISA parallel printer interfaces
lpt0 at isa? port 0x378 irq 7 # standard PC parallel ports
lpt1 at isa? port 0x278
lpt2 at isa? port 0x3bc
# Hardware monitors
# AMD 768 and 8111 power/ACPI controllers
amdpm* at pci? dev ? function ? # RNG and SMBus 1.0 interface
#iic* at amdpm? # sensors below are on this bus
#adt7463c* at iic? addr 0x2C # Unknown other motherboard(s)
#adt7463c* at iic? addr 0x2D # Tyan S2881
#adt7463c* at iic? addr 0x2E # Tyan S2882-D
# Intel PIIX4 power management controllers
piixpm* at pci? dev ? function ? # PIIX4 compatible PM controller
iic* at piixpm? # SMBus on PIIX4
# iTE IT87xxF and compatible hardware monitors
#it0 at isa? port 0x290 # other ports: 0xc00, 0xd00
# LM7[89] and compatible hardware monitors
#lm0 at isa? port 0x290 # other common: 0x280, 0x310
# PC87366 hardware monitor
#nsclpcsio* at isa?
#gpio* at nsclpcsio?
# VIA VT82C686A hardware monitor
#viapm* at pci? dev ? function ?
#viaenv* at viapm?
# I2O devices
iop* at pci? dev ? function ? # I/O processor
iopsp* at iop? tid ? # SCSI/FC-AL ports
ld* at iop? tid ? # block devices
dpti* at iop? tid 0 # DPT/Adaptec control interface
# GPIO devices
#gpio* at gscpcib?
# 1-Wire support
#gpioow* at gpio? offset 6 mask 0x1 # 1-wire bitbanging via gpio
#onewire* at gpioow?
# 1-Wire devices
#owtemp* at onewire? # Temperature sensors
# SCSI Controllers and Devices
# PCI SCSI controllers
#adv* at pci? dev ? function ? # AdvanSys 1200[A,B], 9xx[U,UA] SCSI
#adw* at pci? dev ? function ? # AdvanSys 9x0UW[D], 3940U[2,3]W SCSI
#ahc* at pci? dev ? function ? # Adaptec [23]94x, aic78x0 SCSI
#ahd* at pci? dev ? function ? # Adaptec 29320, 39320 (aic790x) SCSI
#bha* at pci? dev ? function ? # BusLogic 9xx SCSI
#dpt* at pci? dev ? function ? # DPT SmartCache/SmartRAID
#iha* at pci? dev ? function ? # Initio INIC-940/950 SCSI
#isp* at pci? dev ? function ? # Qlogic ISP [12]0x0 SCSI/FibreChannel
#mfi* at pci? dev ? function ? # LSI MegaRAID SAS
#mly* at pci? dev ? function ? # Mylex AcceleRAID and eXtremeRAID
#mpt* at pci? dev ? function ? # LSI Fusion SCSI/FC
#njs* at pci? dev ? function ? # Workbit NinjaSCSI-32
#pcscp* at pci? dev ? function ? # AMD 53c974 PCscsi-PCI SCSI
#siop* at pci? dev ? function ? # Symbios 53c8xx SCSI
#esiop* at pci? dev ? function ? # Symbios 53c875 SCSI and newer
#options SIOP_SYMLED # drive the act. LED in software
#trm* at pci? dev ? function ? # Tekram DC-395U/UW/F, DC-315/U SCSI
# EISA SCSI controllers
#ahb* at eisa? slot ? # Adaptec 174[02] SCSI
#ahc* at eisa? slot ? # Adaptec 274x, aic7770 SCSI
#bha* at eisa? slot ? # BusLogic 7xx SCSI
#dpt* at eisa? slot ? # DPT EATA SCSI
#uha* at eisa? slot ? # UltraStor 24f SCSI
# PCMCIA SCSI controllers
#aic* at pcmcia? function ? # Adaptec APA-1460 SCSI
#esp* at pcmcia? function ? # Qlogic ESP406/FAS408 SCSI
#spc* at pcmcia? function ? # Fujitsu MB87030/MB89352 SCSI
# ISA Plug-and-Play SCSI controllers
#aha* at isapnp? # Adaptec AHA-154[02
#aic* at isapnp? # Adaptec AHA-1520B
# ISA SCSI controllers
#adv0 at isa? port ? irq ? drq ? # AdvanSys APB-514[02] SCSI
#aha0 at isa? port 0x330 irq ? drq ? # Adaptec 154[02] SCSI
#aha1 at isa? port 0x334 irq ? drq ?
#ahc0 at isa? port ? irq ? # Adaptec 284x SCSI
#aic0 at isa? port 0x340 irq 11 # Adaptec 152[02] SCSI
#bha0 at isa? port 0x330 irq ? drq ? # BusLogic [457]4X SCSI
#bha1 at isa? port 0x334 irq ? drq ?
# The "nca" and "dpt" probes might give false hits or hang your machine.
#dpt0 at isa? port 0x170 irq ? drq ? # DPT SmartCache/SmartRAID
#nca0 at isa? port 0x360 irq 15 # Port-mapped NCR 53C80 controller
#nca1 at isa? iomem 0xd8000 irq 5 # Memory-mapped controller (T128, etc.)
#sea0 at isa? iomem 0xc8000 irq 5 # Seagate/Future Domain SCSI
#uha0 at isa? port 0x330 irq ? drq ? # UltraStor [13]4f SCSI
#uha1 at isa? port 0x340 irq ? drq ?
#wds0 at isa? port 0x350 irq 15 drq 6 # WD7000 and TMC-7000 controllers
#wds1 at isa? port 0x358 irq 11 drq 5
# CardBus SCSI cards
#adv* at cardbus? function ? # AdvanSys 1200[A,B], 9xx[U,UA] SCSI
#ahc* at cardbus? function ? # Adaptec ADP-1480
#njs* at cardbus? function ? # Workbit NinjaSCSI-32
# MCA SCSI cards
#aha* at mca? slot ? # Adaptec AHA-1640
# SCSI bus support
scsibus* at scsi?
# SCSI devices
sd* at scsibus? target ? lun ? # SCSI disk drives
st* at scsibus? target ? lun ? # SCSI tape drives
cd* at scsibus? target ? lun ? # SCSI CD-ROM drives
ch* at scsibus? target ? lun ? # SCSI autochangers
ses* at scsibus? target ? lun ? # SCSI Enclosure Services devices
ss* at scsibus? target ? lun ? # SCSI scanners
uk* at scsibus? target ? lun ? # SCSI unknown
# RAID controllers and devices
#aac* at pci? dev ? function ? # Adaptec AAC family
#amr* at pci? dev ? function ? # AMI/LSI Logic MegaRAID
#cac* at eisa? slot ? # Compaq EISA array controllers
#cac* at pci? dev ? function ? # Compaq PCI array controllers
#ciss* at pci? dev ? function ? # HP Smart Array controllers
#icp* at pci? dev ? function ? # ICP-Vortex GDT & Intel RAID
#mlx* at pci? dev ? function ? # Mylex DAC960 & DEC SWXCR family
#mlx* at eisa? slot ? # Mylex DAC960 & DEC SWXCR family
#twa* at pci? dev ? function ? # 3ware Escalade 95xx RAID controllers
#twe* at pci? dev ? function ? # 3ware Escalade RAID controllers
#ld* at aac? unit ? # logical disk devices
#ld* at amr? unit ?
#ld* at cac? unit ?
#ld* at icp? unit ?
#ld* at twa? unit ?
#ld* at twe? unit ?
#ld* at mlx? unit ?
#icpsp* at icp? unit ? # SCSI pass-through
# IDE and related devices
# PCI IDE controllers - see pciide(4) for supported hardware.
# The 0x0001 flag force the driver to use DMA, even if the driver doesn't know
# how to set up DMA modes for this chip. This may work, or may cause
# a machine hang with some controllers.
pciide* at pci? dev ? function ? flags 0x0000 # GENERIC pciide driver
acardide* at pci? dev ? function ? # Acard IDE controllers
aceride* at pci? dev ? function ? # Acer Lab IDE controllers
ahcisata* at pci? dev ? function ? # AHCI SATA controllers
artsata* at pci? dev ? function ? # Intel i31244 SATA controller
cmdide* at pci? dev ? function ? # CMD tech IDE controllers
cypide* at pci? dev ? function ? # Cypress IDE controllers
gcscide* at pci? dev ? function ? # AMD CS5535 Companion IDE
controllers
geodeide* at pci? dev ? function ? # AMD Geode IDE controllers
hptide* at pci? dev ? function ? # Triones/HighPoint IDE
controllers
iteide* at pci? dev ? function ? # IT Express IDE controllers
ixpide* at pci? dev ? function ? # ATI IXP IDE controllers
jmide* at pci? dev ? function ? # JMicron PCI-e PATA/SATA
controllers
ahcisata* at jmide?
optiide* at pci? dev ? function ? # Opti IDE controllers
piixide* at pci? dev ? function ? # Intel IDE controllers
pdcide* at pci? dev ? function ? # Promise IDE controllers
pdcsata* at pci? dev ? function ? # Promise SATA150 controllers
rccide* at pci? dev ? function ? # ServerWorks IDE controllers
satalink* at pci? dev ? function ? # SiI SATALink controllers
siside* at pci? dev ? function ? # SiS IDE controllers
slide* at pci? dev ? function ? # Symphony Labs IDE controllers
svwsata* at pci? dev ? function ? # ServerWorks SATA controllers
stpcide* at pci? dev ? function ? # STMicro STPC IDE controllers
viaide* at pci? dev ? function ? # VIA/AMD/Nvidia IDE controllers
# ISA Plug-and-Play IDE controllers
wdc* at isapnp?
# PCMCIA IDE controllers
wdc* at pcmcia? function ?
# CardBus IDE controllers
#njata* at cardbus? function ? flags 0x01 # Workbit NinjaATA-32
# ISA ST506, ESDI, and IDE controllers
# Use flags 0x01 if you want to try to use 32bits data I/O (the driver will
# fall back to 16bits I/O if 32bits I/O are not functional).
# Some controllers pass the initial 32bit test, but will fail later.
wdc0 at isa? port 0x1f0 irq 14 flags 0x00
wdc1 at isa? port 0x170 irq 15 flags 0x00
# ATA (IDE) bus support
atabus* at ata?
# IDE drives
# Flags are used only with controllers that support DMA operations
# and mode settings (e.g. some pciide controllers)
# The lowest order four bits (rightmost digit) of the flags define the PIO
# mode to use, the next set of four bits the DMA mode and the third set the
# UltraDMA mode. For each set of four bits, the 3 lower bits define the mode
# to use, and the last bit must be 1 for this setting to be used.
# For DMA and UDMA, 0xf (1111) means 'disable'.
# 0x0fac means 'use PIO mode 4, DMA mode 2, disable UltraDMA'.
# (0xc=1100, 0xa=1010, 0xf=1111)
# 0x0000 means "use whatever the drive claims to support".
wd* at atabus? drive ? flags 0x0000
# ATA RAID configuration support, as found on some Promise controllers.
pseudo-device ataraid
ld* at ataraid? vendtype ? unit ?
# ATAPI bus support
atapibus* at atapi?
# ATAPI devices
# flags have the same meaning as for IDE drives.
cd* at atapibus? drive ? flags 0x0000 # ATAPI CD-ROM drives
sd* at atapibus? drive ? flags 0x0000 # ATAPI disk drives
st* at atapibus? drive ? flags 0x0000 # ATAPI tape drives
uk* at atapibus? drive ? flags 0x0000 # ATAPI unknown
# Miscellaneous mass storage devices
# ISA floppy
fdc0 at isa? port 0x3f0 irq 6 drq 2 # standard PC floppy controllers
#fdc1 at isa? port 0x370 irq ? drq ?
fd* at fdc? drive ? # the drives themselves
# some machines need you to do this instead of fd*
#fd0 at fdc0 drive 0
# ISA CD-ROM devices
#mcd0 at isa? port 0x300 irq 10 # Mitsumi CD-ROM drives
# ISA tape devices
# note: the wt driver conflicts unpleasantly with SMC boards at the
# same I/O address. The probe reprograms their EEPROMs. Don't
# uncomment it unless you are actually using it.
#wt0 at isa? port 0x308 irq 5 drq 1 # Archive and Wangtek QIC tape drives
# MCA ESDI devices
edc* at mca? slot ? # IBM ESDI Disk Controllers
ed* at edc?
# Network Interfaces
# PCI network interfaces
an* at pci? dev ? function ? # Aironet PC4500/PC4800 (802.11)
ath* at pci? dev ? function ? # Atheros 5210/5211/5212 802.11
atw* at pci? dev ? function ? # ADMtek ADM8211 (802.11)
bce* at pci? dev ? function ? # Broadcom 4401 10/100 Ethernet
bge* at pci? dev ? function ? # Broadcom 570x gigabit Ethernet
bnx* at pci? dev ? function ? # Broadcom NetXtremeII gigabit Ethernet
dge* at pci? dev ? function ? # Intel 82597 10GbE LR
en* at pci? dev ? function ? # ENI/Adaptec ATM
ep* at pci? dev ? function ? # 3Com 3c59x
epic* at pci? dev ? function ? # SMC EPIC/100 Ethernet
esh* at pci? dev ? function ? # Essential HIPPI card
ex* at pci? dev ? function ? # 3Com 90x[BC]
fpa* at pci? dev ? function ? # DEC DEFPA FDDI
fxp* at pci? dev ? function ? # Intel EtherExpress PRO 10+/100B
gsip* at pci? dev ? function ? # NS83820 Gigabit Ethernet
hme* at pci? dev ? function ? # Sun Microelectronics STP2002-STQ
ipw* at pci? dev ? function ? # Intel PRO/Wireless 2100
iwi* at pci? dev ? function ? # Intel PRO/Wireless 2200BG
le* at pci? dev ? function ? # PCnet-PCI Ethernet
lmc* at pci? dev ? function ? # Lan Media Corp SSI/HSSI/DS3
mskc* at pci? dev ? function ? # Marvell Yukon 2 Gigabit Ethernet
msk* at mskc? # Marvell Yukon 2 Gigabit Ethernet
mtd* at pci? dev ? function ? # Myson MTD803 3-in-1 Ethernet
#ndis* at pci? dev ? function ? # Experimental - NDIS Network Driver
ne* at pci? dev ? function ? # NE2000-compatible Ethernet
nfe* at pci? dev ? function ? # NVIDIA nForce Ethernet
ntwoc* at pci? dev ? function ? # Riscom/N2 PCI Sync Serial
pcn* at pci? dev ? function ? # AMD PCnet-PCI Ethernet
ral* at pci? dev ? function ? # Ralink Technology RT25x0 802.11a/b/g
re* at pci? dev ? function ? # Realtek 8139C+/8169/8169S/8110S
rtk* at pci? dev ? function ? # Realtek 8129/8139
rtw* at pci? dev ? function ? # Realtek 8180L (802.11)
sf* at pci? dev ? function ? # Adaptec AIC-6915 Ethernet
sip* at pci? dev ? function ? # SiS 900/DP83815 Ethernet
skc* at pci? dev ? function ? # SysKonnect SK9821 Gigabit Ethernet
sk* at skc? # SysKonnect SK9821 Gigabit Ethernet
ste* at pci? dev ? function ? # Sundance ST-201 Ethernet
stge* at pci? dev ? function ? # Sundance/Tamarack TC9021 Gigabit
ti* at pci? dev ? function ? # Alteon ACEnic gigabit Ethernet
tl* at pci? dev ? function ? # ThunderLAN-based Ethernet
tlp* at pci? dev ? function ? # DECchip 21x4x and clones
txp* at pci? dev ? function ? # 3com 3cr990
vge* at pci? dev ? function ? # VIATech VT612X Gigabit Ethernet
vr* at pci? dev ? function ? # VIA Rhine Fast Ethernet
wi* at pci? dev ? function ? # Intersil Prism Mini-PCI (802.11b)
wm* at pci? dev ? function ? # Intel 8254x gigabit
wpi* at pci? dev ? function ? # Intel PRO/Wireless 3945ABG
xge* at pci? dev ? function ? # Neterion (S2io) Xframe-I 10GbE
# EISA network interfaces
ep* at eisa? slot ? # 3Com 3c579 Ethernet
fea* at eisa? slot ? # DEC DEFEA FDDI
tlp* at eisa? slot ? # DEC DE-425 Ethernet
# ISA Plug-and-Play network interfaces
an* at isapnp? # Aironet 802.11
ep* at isapnp? # 3Com 3c509 Ethernet
fmv* at isapnp? # Fujitsu FMV-183
le* at isapnp? # AMD PCnet-ISA Ethernet
ne* at isapnp? # NE2000-compatible Ethernet
tr* at isapnp? # IBM/3COM TROPIC Token-Ring
# PCMCIA network interfaces
an* at pcmcia? function ? # Aironet PC4500/PC4800 (802.11)
awi* at pcmcia? function ? # BayStack 650/660 (802.11FH/DS)
cnw* at pcmcia? function ? # Xircom/Netwave AirSurfer
cs* at pcmcia? function ? # CS89xx Ethernet
ep* at pcmcia? function ? # 3Com 3c589 and 3c562 Ethernet
mbe* at pcmcia? function ? # MB8696x based Ethernet
ne* at pcmcia? function ? # NE2000-compatible Ethernet
ray* at pcmcia? function ? # Raytheon Raylink (802.11)
sm* at pcmcia? function ? # Megahertz Ethernet
# tr at pcmcia has problems with Cardbus bridges
#tr* at pcmcia? function ? # TROPIC based Token-Ring
wi* at pcmcia? function ? # Lucent/Intersil WaveLan IEEE (802.11)
xirc* at pcmcia? function ? # Xircom CreditCard Ethernet
com* at xirc?
xi* at xirc?
mhzc* at pcmcia? function ? # Megahertz Ethernet/Modem combo cards
com* at mhzc?
sm* at mhzc?
# ISA network interfaces
ate0 at isa? port 0x2a0 irq ? # AT1700
cs0 at isa? port 0x300 iomem ? irq ? drq ? # CS8900 Ethernet
ec0 at isa? port 0x250 iomem 0xd8000 irq 9 # 3Com 3c503 Ethernet
eg0 at isa? port 0x280 irq 9 # 3C505 ethernet cards
el0 at isa? port 0x300 irq 9 # 3C501 ethernet cards
ep* at isa? port ? irq ? # 3C509 ethernet cards
ef0 at isa? port 0x360 iomem 0xd0000 irq 7 # 3C507
ai0 at isa? port 0x360 iomem 0xd0000 irq 7 # StarLAN
fmv0 at isa? port 0x2a0 irq ? # FMV-181/182
ix0 at isa? port 0x300 irq 10 # EtherExpress/16
iy0 at isa? port 0x360 irq ? # EtherExpress PRO 10 ISA
lc0 at isa? port 0x320 iomem ? irq ? # DEC EtherWORKS III (LEMAC)
#depca0 at isa? port 0x300 iomem 0xc8000 iosiz 0x8000 irq 5 # DEPCA
#le* at depca?
nele0 at isa? port 0x320 irq 9 drq 7 # NE2100
le* at nele?
#ntwoc0 at isa? port 0x300 irq 5 iomem 0xc8000 flags 1 # Riscom/N2 sync serial
bicc0 at isa? port 0x320 irq 10 drq 7 # BICC IsoLan
le* at bicc?
ne0 at isa? port 0x280 irq 9 # NE[12]000 ethernet cards
ne1 at isa? port 0x300 irq 10
sm0 at isa? port 0x300 irq 10 # SMC91C9x Ethernet
tr0 at isa? port 0xa20 iomem 0xd8000 irq ? # IBM TROPIC based Token-Ring
tr1 at isa? port 0xa24 iomem 0xd0000 irq ? # IBM TROPIC based Token-Ring
tr* at isa? port ? irq ? # 3COM TROPIC based Token-Ring
we0 at isa? port 0x280 iomem 0xd0000 irq 9 # WD/SMC Ethernet
we1 at isa? port 0x300 iomem 0xcc000 irq 10
# CardBus network cards
#ath* at cardbus? function ? # Atheros 5210/5211/5212 802.11
#atw* at cardbus? function ? # ADMtek ADM8211 (802.11)
#ex* at cardbus? function ? # 3Com 3C575TX
#fxp* at cardbus? function ? # Intel i8255x
#rtk* at cardbus? function ? # Realtek 8129/8139
#ral* at cardbus? function ? # Ralink Technology
#rtw* at cardbus? function ? # Realtek 8180L (802.11)
#tlp* at cardbus? function ? # DECchip 21143
# MCA network cards
elmc* at mca? slot ? # 3Com EtherLink/MC (3c523)
ep* at mca? slot ? # 3Com EtherLink III (3c529)
we* at mca? slot ? # WD/SMC Ethernet
ate* at mca? slot ? # Allied Telesis AT1720
ne* at mca? slot ? # Novell NE/2 and clones
tr* at mca? slot ? # IBM Token Ring adapter
tra* at mca? slot ? # Tiara LANCard/E and clones
le* at mca? slot ? # SKNET Personal/MC2+
# MII/PHY support
acphy* at mii? phy ? # Altima AC101 and AMD Am79c874 PHYs
amhphy* at mii? phy ? # AMD 79c901 Ethernet PHYs
bmtphy* at mii? phy ? # Broadcom BCM5201 and BCM5202 PHYs
brgphy* at mii? phy ? # Broadcom BCM5400-family PHYs
ciphy* at mii? phy ? # Cicada CS8201 Gig-E PHYs
dmphy* at mii? phy ? # Davicom DM9101 PHYs
exphy* at mii? phy ? # 3Com internal PHYs
gentbi* at mii? phy ? # Generic Ten-Bit 1000BASE-[CLS]X PHYs
glxtphy* at mii? phy ? # Level One LXT-1000 PHYs
gphyter* at mii? phy ? # NS83861 Gig-E PHY
icsphy* at mii? phy ? # Integrated Circuit Systems ICS189x
igphy* at mii? phy ? # Intel IGP01E1000
ikphy* at mii? phy ? # Intel 82563 PHYs
inphy* at mii? phy ? # Intel 82555 PHYs
iophy* at mii? phy ? # Intel 82553 PHYs
lxtphy* at mii? phy ? # Level One LXT-970 PHYs
makphy* at mii? phy ? # Marvell Semiconductor 88E1000 PHYs
nsphy* at mii? phy ? # NS83840 PHYs
nsphyter* at mii? phy ? # NS83843 PHYs
pnaphy* at mii? phy ? # generic HomePNA PHYs
qsphy* at mii? phy ? # Quality Semiconductor QS6612 PHYs
rgephy* at mii? phy ? # Realtek 8169S/8110S internal PHYs
rlphy* at mii? phy ? # Realtek 8139/8201L PHYs
sqphy* at mii? phy ? # Seeq 80220/80221/80223 PHYs
tlphy* at mii? phy ? # ThunderLAN PHYs
tqphy* at mii? phy ? # TDK Semiconductor PHYs
ukphy* at mii? phy ? # generic unknown PHYs
urlphy* at mii? phy ? # Realtek RTL8150L internal PHYs
# USB Controller and Devices
# PCI USB controllers
ehci* at pci? dev ? function ? # Enhanced Host Controller
ohci* at pci? dev ? function ? # Open Host Controller
uhci* at pci? dev ? function ? # Universal Host Controller (Intel)
# CardBus USB controllers
#ehci* at cardbus? function ? # Enhanced Host Controller
#ohci* at cardbus? function ? # Open Host Controller
#uhci* at cardbus? function ? # Universal Host Controller (Intel)
# ISA USB controllers
#slhci0 at isa? port 0x300 irq 5 # ScanLogic SL811HS
# USB bus support
usb* at ehci?
usb* at ohci?
usb* at uhci?
#usb* at slhci?
# USB Hubs
uhub* at usb?
uhub* at uhub? port ? configuration ? interface ?
# USB HID device
uhidev* at uhub? port ? configuration ? interface ?
# USB Mice
ums* at uhidev? reportid ?
wsmouse* at ums? mux 0
# USB eGalax touch-panel
uep* at uhub? port ?
wsmouse* at uep? mux 0
# USB Keyboards
ukbd* at uhidev? reportid ?
wskbd* at ukbd? console ? mux 1
# USB serial adapter
ucycom* at uhidev? reportid ?
# USB Generic HID devices
uhid* at uhidev? reportid ?
# USB Printer
ulpt* at uhub? port ? configuration ? interface ?
# USB Modem
umodem* at uhub? port ? configuration ?
ucom* at umodem?
# USB Mass Storage
umass* at uhub? port ? configuration ? interface ?
wd* at umass?
# USB audio
uaudio* at uhub? port ? configuration ?
# USB MIDI
umidi* at uhub? port ? configuration ?
# USB IrDA
# USB-IrDA bridge spec
uirda* at uhub? port ? configuration ? interface ?
irframe* at uirda?
# SigmaTel STIr4200 USB/IrDA Bridge
ustir* at uhub? port ?
irframe* at ustir?
# USB Ethernet adapters
aue* at uhub? port ? # ADMtek AN986 Pegasus based adapters
axe* at uhub? port ? # ASIX AX88172 based adapters
cdce* at uhub? port ? # CDC, Ethernet Networking Control Model
cue* at uhub? port ? # CATC USB-EL1201A based adapters
kue* at uhub? port ? # Kawasaki LSI KL5KUSB101B based adapters
udav* at uhub? port ? # Davicom DM9601 based adapters
url* at uhub? port ? # Realtek RTL8150L based adapters
# USB 802.11 adapters
atu* at uhub? port ? # Atmel AT76C50XX based adapters
ral* at uhub? port ? # Ralink Technology RT25x0 802.11a/b/g
rum* at uhub? port ? # Ralink Technology RT2501/RT2601 802.11a/b/g
# Prolific PL2301/PL2302 host-to-host adapter
upl* at uhub? port ?
# Serial adapters
ubsa* at uhub? port ? # Belkin serial adapter
ucom* at ubsa? portno ?
uftdi* at uhub? port ? # FTDI FT8U100AX serial adapter
ucom* at uftdi? portno ?
uipaq* at uhub? port ? # iPAQ PDAs
ucom* at uipaq? portno ?
umct* at uhub? port ? # MCT USB-RS232 serial adapter
ucom* at umct? portno ?
uplcom* at uhub? port ? # I/O DATA USB-RSAQ2 serial adapter
ucom* at uplcom? portno ?
uslsa* at uhub? port ? # Silicon Labs USB-RS232 serial adapter
ucom* at uslsa? portno ?
uvscom* at uhub? port ? # SUNTAC Slipper U VS-10U serial adapter
ucom* at uvscom? portno ?
# Diamond Multimedia Rio 500
urio* at uhub? port ?
# USB Handspring Visor
uvisor* at uhub? port ?
ucom* at uvisor?
# Kyocera AIR-EDGE PHONE
ukyopon* at uhub? port ?
ucom* at ukyopon? portno ?
# USB scanners
uscanner* at uhub? port ?
# USB scanners that use SCSI emulation, e.g., HP5300
usscanner* at uhub? port ?
# Topfield TF5000PVR range of DVB recorders
utoppy* at uhub? port ?
# Y@P firmware loader
uyap* at uhub? port ?
# D-Link DSB-R100 USB radio
udsbr* at uhub? port ?
radio* at udsbr?
# USB Generic driver
ugen* at uhub? port ?
# On ugen bulk endpoints, perform read-ahead and write-behind.
options UGEN_BULK_RA_WB
# IrDA and Consumer Ir devices
# Toshiba Oboe
#oboe* at pci? dev ? function ?
#irframe* at oboe?
# PCI IEEE1394 controllers
fwohci* at pci? dev ? function ? # IEEE1394 Open Host Controller
# CardBus IEEE1394 controllers
#fwohci* at cardbus? function ? # IEEE1394 Open Host Controller
ieee1394if* at fwohci?
fwip* at ieee1394if? # IP over IEEE1394
sbp* at ieee1394if? euihi ? euilo ? # SCSI over IEEE1394
# Audio Devices
# PCI audio devices
#auacer* at pci? dev ? function ? # ALi M5455 integrated AC'97 Audio
#auich* at pci? dev ? function ? # Intel ICH integrated AC'97 Audio
#auixp* at pci? dev ? function ? # ATI IXP AC'97 Audio
#autri* at pci? dev ? function ? # Trident 4DWAVE based AC'97 Audio
#auvia* at pci? dev ? function ? # VIA VT82C686A integrated AC'97 Audio
#azalia* at pci? dev ? function ? # High Definition Audio
#clcs* at pci? dev ? function ? # Cirrus Logic CS4280
#clct* at pci? dev ? function ? # Cirrus Logic CS4281
#cmpci* at pci? dev ? function ? # C-Media CMI8338/8738
#eap* at pci? dev ? function ? # Ensoniq AudioPCI
#emuxki* at pci? dev ? function ? # Creative SBLive! and PCI512
#esa* at pci? dev ? function ? # ESS Allegro-1 / Maestro-3 PCI Audio
#esm* at pci? dev ? function ? # ESS Maestro-1/2/2e PCI Audio
Accelerator
#eso* at pci? dev ? function ? # ESS Solo-1 PCI AudioDrive
#fms* at pci? dev ? function ? # Forte Media FM801
#neo* at pci? dev ? function ? # NeoMagic 256 AC'97 Audio
#sv* at pci? dev ? function ? # S3 SonicVibes
#yds* at pci? dev ? function ? # Yamaha DS-1 PCI Audio
# ISA Plug-and-Play audio devices
#ess* at isapnp? # ESS Tech ES1887, ES1888, ES888 audio
#guspnp* at isapnp? # Gravis Ultra Sound PnP audio
#sb* at isapnp? # SoundBlaster-compatible audio
#wss* at isapnp? # Windows Sound System
ym* at isapnp? # Yamaha OPL3-SA[23] audio
# ISA audio devices
# the "aria" probe might give false hits
#aria0 at isa? port 0x290 irq 10 # Aria
#ess0 at isa? port 0x220 irq 5 drq 1 drq2 5 # ESS 18XX
#gus0 at isa? port 0x220 irq 7 drq 1 drq2 6 # Gravis Ultra Sound
#pas0 at isa? port 0x220 irq 7 drq 1 # ProAudio Spectrum
#sb0 at isa? port 0x220 irq 5 drq 1 drq2 5 # SoundBlaster
#wss0 at isa? port 0x530 irq 10 drq 0 drq2 1 # Windows Sound System
# PCMCIA audio devices
#esl* at pcmcia? function ? # ESS 1688 AudioDrive
#cms0 at isa? port 0x220 # Creative Music System
# OPL[23] FM synthesizers
#opl0 at isa? port 0x388 # use only if not attached to sound card
#opl* at cmpci? flags 1
#opl* at esl?
#opl* at eso?
#opl* at ess?
#opl* at fms?
#opl* at sb?
#opl* at sv?
#opl* at wss?
#opl* at yds?
#opl* at ym?
# Audio support
audio* at audiobus?
# MPU 401 UARTs
#mpu* at isa? port 0x330 irq 9 # MPU401 or compatible card
#mpu* at isapnp?
#mpu* at cmpci?
#mpu* at eso?
#mpu* at fms?
#mpu* at sb?
#mpu* at yds?
#mpu* at ym?
# MIDI support
midi* at midibus?
midi* at pcppi? # MIDI interface to the PC speaker
# The spkr driver provides a simple tone interface to the built in speaker.
#spkr0 at pcppi? # PC speaker
# FM-Radio devices
# ISA radio devices
#az0 at isa? port 0x350 # Aztech/PackardBell FM Radio Card
#az1 at isa? port 0x358
#rt0 at isa? port 0x20c # AIMS Lab Radiotrack & compatible
#rt1 at isa? port 0x284
#rt2 at isa? port 0x30c
#rt3 at isa? port 0x384
#rtii0 at isa? port 0x20c # AIMS Lab Radiotrack II FM Radio Card
#rtii1 at isa? port 0x30c
#sf2r0 at isa? port 0x384 # SoundForte RadioLink SF16-FMR2 FM Radio Card
# PCI radio devices
#gtp* at pci? dev ? function ? # Guillemot Maxi Radio FM 2000 Radio Card
# Radio support
#radio* at az?
#radio* at gtp?
#radio* at rt?
#radio* at rtii?
#radio* at sf2r?
# TV cards
# Brooktree 848/849/878/879 based TV cards
#bktr* at pci? dev ? function ?
#radio* at bktr?
# Bluetooth Controller and Device support
# Bluetooth PCMCIA Controllers
bt3c* at pcmcia? function ? # 3Com 3CRWB6096-A
# Bluetooth USB Controllers
ubt* at uhub? port ? configuration ? interface ?
# Bluetooth Device Hub
bthub* at bt3c?
bthub* at ubt?
# Bluetooth HID support
bthidev* at bthub?
# Bluetooth Mouse
btms* at bthidev? reportid ?
wsmouse* at btms? mux 0
# Bluetooth Keyboard
btkbd* at bthidev? reportid ?
wskbd* at btkbd? console ? mux 1
# Bluetooth Audio support
btsco* at bthub?
# Mice
# ISA busmice
lms0 at isa? port 0x23c irq 5 # Logitech bus mouse
lms1 at isa? port 0x238 irq 5
mms0 at isa? port 0x23c irq 5 # Microsoft InPort mouse
mms1 at isa? port 0x238 irq 5
wsmouse* at lms? mux 0
wsmouse* at mms? mux 0
# Cryptographic Devices
# PCI cryptographic devices
#glxsb* at pci? dev ? function ? # AMD Geode LX Security Block
#hifn* at pci? dev ? function ? # Hifn 7755/7811/795x
#ubsec* at pci? dev ? function ? # Broadcom 5501/5601/580x/582x
# Joysticks
#joy* at pnpbios? index ? # Game port
# ISA Plug-and-Play joysticks
#joy* at isapnp? # Game ports (usually on audio cards)
# PCI joysticks
#joy* at pci? # Game ports (usually on audio cards)
#joy* at eap? # See CAVEATS in eap(4) before enabling
#joy* at eso? # ESS Solo-1 on-board joystick
# ISA joysticks. Probe is a little strange; add only if you have one.
#joy0 at isa? port 0x201
# Miscellaneous Devices
geodegcb* at pci? dev ? function ? # Geode GCB area
geodewdog* at geodegcb? # AMD Geode SC1100 watchdog timer
geodecntr* at geodegcb? # AMD Geode SC1100 high res. counter
# Planetconnect Satellite receiver driver.
#satlink0 at isa? port 0x300 drq 1
# Middle Digital, Inc. PCI-Weasel serial console board control
# devices (watchdog timer, etc.)
#weasel* at pci?
# Pull in optional local configuration
include "arch/i386/conf/GENERIC.local"
# Pseudo-Devices
pseudo-device crypto # /dev/crypto device
pseudo-device swcrypto # software crypto implementation
# disk/mass storage pseudo-devices
#pseudo-device bio # RAID control device driver
#pseudo-device ccd 4 # concatenated/striped disk devices
#pseudo-device cgd 4 # cryptographic disk devices
#pseudo-device raid 8 # RAIDframe disk driver
#options RAID_AUTOCONFIG # auto-configuration of RAID components
# Options to enable various other RAIDframe RAID types.
#options RF_INCLUDE_EVENODD=1
#options RF_INCLUDE_RAID5_RS=1
#options RF_INCLUDE_PARITYLOGGING=1
#options RF_INCLUDE_CHAINDECLUSTER=1
#options RF_INCLUDE_INTERDECLUSTER=1
#options RF_INCLUDE_PARITY_DECLUSTERING=1
#options RF_INCLUDE_PARITY_DECLUSTERING_DS=1
#pseudo-device fss 4 # file system snapshot device
pseudo-device md 1 # memory disk device (ramdisk)
pseudo-device vnd # disk-like interface to files
options VND_COMPRESSION # compressed vnd(4)
# network pseudo-devices
pseudo-device bpfilter # Berkeley packet filter
#pseudo-device carp # Common Address Redundancy Protocol
#pseudo-device ipfilter # IP filter (firewall) and NAT
pseudo-device loop # network loopback
#pseudo-device ppp # Point-to-Point Protocol
#pseudo-device pppoe # PPP over Ethernet (RFC 2516)
#pseudo-device sl # Serial Line IP
#pseudo-device strip # Starmode Radio IP (Metricom)
#pseudo-device irframetty # IrDA frame line discipline
#pseudo-device tap # virtual Ethernet
#pseudo-device tun # network tunneling over tty
#pseudo-device gre # generic L3 over IP tunnel
#pseudo-device gif # IPv[46] over IPv[46] tunnel (RFC1933)
#pseudo-device faith # IPv[46] tcp relay translation i/f
pseudo-device stf # 6to4 IPv6 over IPv4 encapsulation
pseudo-device vlan # IEEE 802.1q encapsulation
pseudo-device bridge # simple inter-network bridging
#options BRIDGE_IPF # bridge uses IP/IPv6 pfil hooks too
pseudo-device agr # IEEE 802.3ad link aggregation
#pseudo-device pf # PF packet filter
#pseudo-device pflog # PF log if
# miscellaneous pseudo-devices
pseudo-device pty # pseudo-terminals
#pseudo-device sequencer 1 # MIDI sequencer
# rnd works; RND_COM does not on port i386 yet.
pseudo-device rnd # /dev/random and in-kernel generator
#options RND_COM # use "com" randomness as well (BROKEN)
pseudo-device clockctl # user control of clock subsystem
pseudo-device ksyms # /dev/ksyms
# a pseudo device needed for Coda # also needs CODA (above)
#pseudo-device vcoda 4 # coda minicache <-> venus comm.
# a pseudo device needed for SMBFS
#pseudo-device nsmb # experimental - SMB requester
# wscons pseudo-devices
pseudo-device wsmux # mouse & keyboard multiplexor
pseudo-device wsfont
options FILEASSOC # fileassoc(9) - required for Veriexec
#options FILEASSOC_NHOOKS=4 # Default number of storage slots
# Veriexec
pseudo-device veriexec
#
# Uncomment the fingerprint methods below that are desired. Note that
# removing fingerprint methods will have almost no impact on the kernel
# code size.
#
options VERIFIED_EXEC_FP_RMD160
options VERIFIED_EXEC_FP_SHA256
options VERIFIED_EXEC_FP_SHA384
options VERIFIED_EXEC_FP_SHA512
options VERIFIED_EXEC_FP_SHA1
options VERIFIED_EXEC_FP_MD5
options PAX_MPROTECT=0 # PaX mprotect(2) restrictions
### END CONFIG FILE
"/tmp/mprt-500-dlink/build_netbsd/usr/src/sys/arch/i386/conf/mprt"
### (included from "arch/i386/conf/std.i386")
###> # $NetBSD: std.i386,v 1.26 2005/12/11 12:17:41 christos Exp $
###> #
###> # standard, required NetBSD/i386 'options'
###>
###> machine i386 x86
###> include "conf/std" # MI standard options
###>
###> options EXEC_AOUT # exec a.out binaries
###> options EXEC_ELF32 # exec ELF binaries
###> options EXEC_SCRIPT # exec #! scripts
###>
###> options INET6_MD_CKSUM # machine-dependant code for in6_cksum
###> #options CRYPTO_MD_DES_ENC # machine-dependant code for DES
###> #options CRYPTO_MD_DES_CBC # machine-dependant DES CBC code
###> #options CRYPTO_MD_BF_ENC # machine-dependant code for BF_encrypt
###> #options CRYPTO_MD_BF_CBC # careful: uses bswapl, requires 486
### (end include "arch/i386/conf/std.i386")
### (included from "conf/std")
###> # $NetBSD: std,v 1.7 2006/09/08 20:58:57 elad Exp $
###> #
###> # standard MI 'options'
###> #
###> # this file is for options which can't be off-by-default for some reasons.
###> # "it's commonly used" is NOT a good reason to enable options here.
###>
###> # the following options are on-by-default to keep
###> # kernel config file compatibility.
###> options VMSWAP # Swap device/file support
###> options BUFQ_FCFS # First-come First-serve strategy
###> options BUFQ_DISKSORT # Traditional min seek sort strategy
###> options RFC2292 # Previous version of Adv. Sockets API for IPv6
###> options PTRACE # Include ptrace(2)
###> options COREDUMP # allow processes to coredump.
###>
###> #
###> # Security model.
###> #
###> options secmodel_bsd44 # Traditional 4.4BSD security model
### (end include "conf/std")
### (included from "arch/i386/conf/GENERIC.local")
###> # $NetBSD: GENERIC.local,v 1.3 2005/12/11 12:17:40 christos Exp $
###> #
###> # GENERIC.local -- local additions to the GENERIC configuration
###> #
### (end include "arch/i386/conf/GENERIC.local")
Home |
Main Index |
Thread Index |
Old Index