Re: configuring raid using gpt, large drives

To: current-users%netbsd.org@localhost
Subject: Re: configuring raid using gpt, large drives
From: mlh%goathill.org@localhost (MLH)
Date: Fri, 14 Feb 2020 15:40:38 -0500 (EST)
Continuation of a long story... 

Emmanuel has expended an immense amount of time trying to help me
solve this problem. I finally have accepted that while my motherboard
purports to support EFI booting of large drives, the bios doesn't
appear to support it in any way we can determine.

Nor does it appear to support booting from a raid array that pretty
clearly has been set up correctly.

BAck with 7.x -current I had tried to use gpt with ffs booting to
be able to use these two 4T drives in a raid array but back then
there was some software problem with doing that under NetBSD.

Emmanuel suggested I go back to using a boot wedge to bring up the
bootloader and switching to the raid array.

I had jsut (apparently) got that working, where the bootloader was
comoing up from either of my wd2 or wd3 boot wedges and askign for
the raid0 but then this happened, which is preventing the kernel
from seeing either wd2 or wd3:

[     2.152423] ahcisata1 port 5: device present, speed: 3.0Gb/s
[     2.152423] ahcisata1 port 0: device present, speed: 3.0Gb/s
[     2.152423] ahcisata1 port 4: device present, speed: 3.0Gb/s
[     2.752630] autoconfiguration error: ahcisata1 port 5: setting WDCTL_RST failed for drive 15
[     2.752630] autoconfiguration error: ahcisata1 port 4: setting WDCTL_RST failed for drive 15
[     3.252803] autoconfiguration error: ahcisata1 port 5: drive 15 reset failed, disabling PMP
[     3.252803] autoconfiguration error: ahcisata1 port 4: drive 15 reset failed, disabling PMP
[     3.352837] ahcisata1 port 5: device present, speed: 3.0Gb/s
[     3.352837] ahcisata1 port 4: device present, speed: 3.0Gb/s

wd0 and wd1 are old drives I really need to take offline. wd1 is
getting errors.

Full dmesg:

[     1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
[     1.000000]     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
[     1.000000]     2018, 2019, 2020 The NetBSD Foundation, Inc.  All rights reserved.
[     1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[     1.000000]     The Regents of the University of California.  All rights reserved.

[     1.000000] NetBSD 9.99.46 (HDMIAUDIO) #0: Thu Feb 13 13:00:32 EST 2020
[     1.000000] 	xxxx@xxxxxx:/opt/obj/amd64/opt/src/sys/arch/amd64/compile/HDMIAUDIO
[     1.000000] total memory = 4079 MB
[     1.000000] avail memory = 3933 MB
[     1.000000] pool redzone disabled for 'buf4k'
[     1.000000] pool redzone disabled for 'buf64k'
[     1.000000] timecounter: Timecounters tick every 10.000 msec
[     1.000000] Kernelized RAIDframe activated
[     1.000000] running cgd selftest aes-xts-256 aes-xts-512 done
[     1.000000] timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
[     1.000003] Gigabyte Technology Co., Ltd. H61M-S2-B3 ( )
[     1.000003] mainbus0 (root)
[     1.000003] ACPI: RSDP 0x00000000000F6EA0 000014 (v00 GBT   )
[     1.000003] ACPI: RSDT 0x00000000DF7D3040 00004C (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[     1.000003] ACPI: FACP 0x00000000DF7D3100 000074 (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[     1.000003] ACPI: DSDT 0x00000000DF7D31C0 0049F2 (v01 GBT    GBTUACPI 00001000 MSFT 04000000)
[     1.000003] ACPI: FACS 0x00000000DF7D0000 000040
[     1.000003] ACPI: MSDM 0x00000000DF7D7D00 000055 (v03 GBT    GBTUACPI 42302E31 GBTU 01010101)
[     1.000003] ACPI: HPET 0x00000000DF7D7DC0 000038 (v01 GBT    GBTUACPI 42302E31 GBTU 00000098)
[     1.000003] ACPI: MCFG 0x00000000DF7D7E40 00003C (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[     1.000003] ACPI: ASPT 0x00000000DF7D7F00 000034 (v07 GBT    PerfTune 312E3042 UTBG 01010101)
[     1.000003] ACPI: SSPT 0x00000000DF7D7F40 002270 (v01 GBT    SsptHead 312E3042 UTBG 01010101)
[     1.000003] ACPI: EUDS 0x00000000DF7DA1B0 0000C0 (v01 GBT             00000000      00000000)
[     1.000003] ACPI: TAMG 0x00000000DF7DA270 000382 (v01 GBT    GBT   B0 5455312E BG?? 45240101)
[     1.000003] ACPI: APIC 0x00000000DF7D7C00 0000BC (v01 GBT    GBTUACPI 42302E31 GBTU 01010101)
[     1.000003] ACPI: SSDT 0x00000000DF7DA600 001EC8 (v01 INTEL  PPM RCM  80000001 INTL 20061109)
[     1.000003] ACPI: 2 ACPI AML tables successfully acquired and loaded
[     1.000003] ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x20, 24 pins
[     1.000003] cpu0 at mainbus0 apid 0
[     1.000003] cpu0: Intel(R) Core(TM) i3-2120 CPU @ 3.30GHz, id 0x206a7
[     1.000003] cpu0: node 0, package 0, core 0, smt 0
[     1.000003] cpu1 at mainbus0 apid 2
[     1.000003] cpu1: Intel(R) Core(TM) i3-2120 CPU @ 3.30GHz, id 0x206a7
[     1.000003] cpu1: node 0, package 0, core 1, smt 0
[     1.000003] cpu2 at mainbus0 apid 1
[     1.000003] cpu2: Intel(R) Core(TM) i3-2120 CPU @ 3.30GHz, id 0x206a7
[     1.000003] cpu2: node 0, package 0, core 0, smt 1
[     1.000003] cpu3 at mainbus0 apid 3
[     1.000003] cpu3: Intel(R) Core(TM) i3-2120 CPU @ 3.30GHz, id 0x206a7
[     1.000003] cpu3: node 0, package 0, core 1, smt 1
[     1.000003] acpi0 at mainbus0: Intel ACPICA 20191213
[     1.000003] acpi0: X/RSDT: OemId <GBT   ,GBTUACPI,42302e31>, AslId <GBTU,01010101>
[     1.000003] acpi0: MCFG: segment 0, bus 0-63, address 0x00000000f4000000
[     1.000003] acpi0: SCI interrupting at int 9
[     1.000003] acpi0: fixed power button present
[     1.000003] timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
[     1.022303] hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
[     1.022303] timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
[     1.022563] acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
[     1.022563] SYSR (PNP0C02) at acpi0 not configured
[     1.022563] attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43
[     1.022563] pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
[     1.022563] spkr0 at pcppi1: PC Speaker
[     1.022563] wsbell at spkr0 not configured
[     1.022563] midi0 at pcppi1: PC speaker
[     1.022563] sysbeep0 at pcppi1
[     1.022563] UAR1 (PNP0501) at acpi0 not configured
[     1.022563] LPT1 (PNP0400) at acpi0 not configured
[     1.022563] PMIO (PNP0C02) at acpi0 not configured
[     1.022563] PTMD (ICD0001) at acpi0 not configured
[     1.022563] CWDT (INT3F0D) at acpi0 not configured
[     1.022563] EXPL (PNP0C02) at acpi0 not configured
[     1.022563] MEM (PNP0C01) at acpi0 not configured
[     1.022563] FWH (INT0800) at acpi0 not configured
[     1.022563] ACPI: Enabled 1 GPEs in block 00 to 3F
[     1.022563] attimer1: attached to pcppi1
[     1.022563] pci0 at mainbus0 bus 0: configuration mode 1
[     1.022563] pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
[     1.022563] pchb0 at pci0 dev 0 function 0: Intel Sandy Bridge (desktop) Host Bridge (rev. 0x09)
[     1.022563] ppb0 at pci0 dev 1 function 0: Intel Sandy Bridge (desktop) PCIe Root port (rev. 0x09)
[     1.022563] ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 5.0GT/s
[     1.022563] pci1 at ppb0 bus 1
[     1.022563] pci1: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.022563] radeon0 at pci1 dev 0 function 0: ATI Technologies Radeon HD 6450 (rev. 0x00)
[     1.022563] hdaudio0 at pci1 dev 0 function 1: HD Audio Controller
[     1.022563] hdaudio0: interrupting at msi0 vec 0
[     1.022563] hdaudio0: HDA ver. 1.0, OSS 1, ISS 0, BSS 0, SDO 1, 64-bit
[     1.022563] hdafg0 at hdaudio0: vendor 1002 product aa01
[     1.022563] hdafg0: HDMI00 2ch: Digital Out [Jack]
[     1.022563] hdafg0: 2ch/0ch 32000Hz 44100Hz 48000Hz PCM16 AC3
[     1.022563] audio0 at hdafg0: playback
[     1.022563] audio0: slinear_le:16 2ch 48000Hz, blk 4ms for playback
[     1.022563] spkr1 at audio0: PC Speaker (synthesized)
[     1.022563] wsbell at spkr1 not configured
[     1.022563] Intel 6 Series Chipset Family MEI (miscellaneous communications, revision 0x04) at pci0 dev 22 function 0 not configured
[     1.022563] ehci0 at pci0 dev 26 function 0: Intel 6 Series Chipset Family USB (rev. 0x05)
[     1.022563] ehci0: interrupting at ioapic0 pin 18
[     1.022563] ehci0: BIOS has given up ownership
[     1.022563] ehci0: EHCI version 1.0
[     1.022563] usb0 at ehci0: USB revision 2.0
[     1.022563] hdaudio1 at pci0 dev 27 function 0: HD Audio Controller
[     1.022563] hdaudio1: interrupting at msi1 vec 0
[     1.022563] hdaudio1: HDA ver. 1.0, OSS 4, ISS 4, BSS 0, SDO 1, 64-bit
[     1.022563] hdafg1 at hdaudio1: vendor 1106 product 0397
[     1.022563] hdafg1: DAC00 2ch: Speaker [Jack], HP Out [Jack]
[     1.022563] hdafg1: ADC01 2ch: Line In [Jack], Mic In [Jack]
[     1.022563] hdafg1: 2ch/2ch 48000Hz PCM16*
[     1.022563] audio1 at hdafg1: playback, capture, full duplex, independent
[     1.022563] audio1: slinear_le:16 2ch 48000Hz, blk 4ms for playback
[     1.022563] audio1: slinear_le:16 2ch 48000Hz, blk 4ms for recording
[     1.022563] spkr2 at audio1: PC Speaker (synthesized)
[     1.022563] wsbell at spkr2 not configured
[     1.022563] ppb1 at pci0 dev 28 function 0: Intel 6 Series Chipset Family PCIe Root Port 1 (rev. 0xb5)
[     1.022563] ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[     1.022563] pci2 at ppb1 bus 2
[     1.022563] pci2: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.022563] ppb2 at pci0 dev 28 function 4: Intel 6 Series Chipset Family PCIe Root Port 5 (rev. 0xb5)
[     1.022563] ppb2: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[     1.022563] ppb2: link is x1 @ 2.5GT/s
[     1.022563] pci3 at ppb2 bus 3
[     1.022563] pci3: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.022563] alc0 at pci3 dev 0 function 0: Atheros AR8151 v2.0 PCIe Gigabit Ethernet
[     1.022563] alc0: interrupting at ioapic0 pin 16
[     1.022563] alc0: Ethernet address 50:e5:49:84:e3:f0
[     1.022563] atphy0 at alc0 phy 0: Atheros AR8035 10/100/1000 PHY, rev. 0
[     1.022563] atphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto
[     1.022563] ppb3 at pci0 dev 28 function 5: Intel 6 Series Chipset Family PCIe Root Port 6 (rev. 0xb5)
[     1.022563] ppb3: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[     1.022563] ppb3: link is x1 @ 2.5GT/s
[     1.022563] pci4 at ppb3 bus 4
[     1.022563] pci4: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.022563] jmide0 at pci4 dev 0 function 0: JMicron Technology JMB363 SATA/PATA Controller (rev. 0x10)
[     1.022563] jmide0: 1 PATA port, 2 SATA ports
[     1.022563] jmide0: interrupting at ioapic0 pin 17
[     1.022563] ahcisata0 at jmide0
[     1.022563] ahcisata0: AHCI revision 1.10, 2 ports, 32 slots, CAP 0xc722ff01<PSC,SSC,PMD,SPM,ISS=0x2=Gen2,SCLO,SAL,SALP,SNCQ,S64A>
[     1.022563] atabus0 at ahcisata0 channel 0
[     1.022563] atabus1 at ahcisata0 channel 1
[     1.022563] jmide0: PCI IDE interface used
[     1.022563] jmide0: bus-master DMA support present
[     1.022563] jmide0: primary channel wired to native-PCI mode
[     1.022563] jmide0: primary channel is unused
[     1.022563] jmide0: secondary channel wired to native-PCI mode
[     1.022563] jmide0: secondary channel is PATA
[     1.022563] atabus2 at jmide0 channel 1
[     1.022563] ehci1 at pci0 dev 29 function 0: Intel 6 Series Chipset Family USB (rev. 0x05)
[     1.022563] ehci1: interrupting at ioapic0 pin 23
[     1.022563] ehci1: BIOS has given up ownership
[     1.022563] ehci1: EHCI version 1.0
[     1.022563] usb1 at ehci1: USB revision 2.0
[     1.022563] ppb4 at pci0 dev 30 function 0: Intel 82801BA Hub-PCI Bridge (rev. 0xa5)
[     1.022563] pci5 at ppb4 bus 5
[     1.022563] pci5: i/o space, memory space enabled
[     1.022563] ichlpcib0 at pci0 dev 31 function 0: Intel H61 LPC (rev. 0x05)
[     1.022563] timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
[     1.022563] ichlpcib0: 24-bit timer
[     1.022563] tco0 at ichlpcib0: TCO (watchdog) timer configured.
[     1.022563] tco0: autoconfiguration error: TCO timer reboot disabled by hardware; hope SMBIOS properly handles it.
[     1.022563] tco0: Min/Max interval 1/367 seconds
[     1.022563] ahcisata1 at pci0 dev 31 function 2: Intel 6 Series Chipset Family AHCI 1 (rev. 0x05)
[     1.022563] ahcisata1: 64-bit DMA
[     1.022563] ahcisata1: AHCI revision 1.30, 4 ports, 32 slots, CAP 0xef22ff43<EMS,PSC,SSC,PMD,SPM,ISS=0x2=Gen2,SCLO,SAL,SALP,SSS,SSNTF,SNCQ,S64A>
[     1.022563] ahcisata1: interrupting at msi2 vec 0
[     1.022563] atabus3 at ahcisata1 channel 0
[     1.022563] atabus4 at ahcisata1 channel 1
[     1.022563] atabus5 at ahcisata1 channel 4
[     1.022563] atabus6 at ahcisata1 channel 5
[     1.022563] ichsmb0 at pci0 dev 31 function 3: Intel 6 Series Chipset Family SMBus Controller (rev. 0x05)
[     1.022563] ichsmb0: interrupting at ioapic0 pin 18
[     1.022563] iic0 at ichsmb0: I2C bus
[     1.022563] isa0 at ichlpcib0
[     1.022563] lpt0 at isa0 port 0x378-0x37b irq 7
[     1.022563] com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
[     1.022563] pckbc0 at isa0 port 0x60-0x64
[     1.022563] acpicpu0 at cpu0: ACPI CPU
[     1.022563] acpicpu0: C1: FFH, lat   1 us, pow  1000 mW
[     1.022563] acpicpu0: C2: FFH, lat  64 us, pow   500 mW
[     1.022563] acpicpu0: C3: FFH, lat  96 us, pow   350 mW
[     1.022563] acpicpu0: P0: FFH, lat  10 us, pow 84000 mW, 3300 MHz
[     1.022563] acpicpu0: P1: FFH, lat  10 us, pow 84000 mW, 3200 MHz
[     1.022563] acpicpu0: P2: FFH, lat  10 us, pow 84000 mW, 3100 MHz
[     1.022563] acpicpu0: P3: FFH, lat  10 us, pow 84000 mW, 3000 MHz
[     1.022563] acpicpu0: P4: FFH, lat  10 us, pow 84000 mW, 2900 MHz
[     1.022563] acpicpu0: P5: FFH, lat  10 us, pow 84000 mW, 2800 MHz
[     1.022563] acpicpu0: P6: FFH, lat  10 us, pow 84000 mW, 2700 MHz
[     1.022563] acpicpu0: P7: FFH, lat  10 us, pow 84000 mW, 2600 MHz
[     1.022563] acpicpu0: P8: FFH, lat  10 us, pow 84000 mW, 2500 MHz
[     1.022563] acpicpu0: P9: FFH, lat  10 us, pow 76000 mW, 2400 MHz
[     1.022563] acpicpu0: P10: FFH, lat  10 us, pow 72000 mW, 2300 MHz
[     1.022563] acpicpu0: P11: FFH, lat  10 us, pow 69000 mW, 2200 MHz
[     1.022563] acpicpu0: P12: FFH, lat  10 us, pow 66000 mW, 2100 MHz
[     1.022563] acpicpu0: P13: FFH, lat  10 us, pow 63000 mW, 2000 MHz
[     1.022563] acpicpu0: P14: FFH, lat  10 us, pow 58000 mW, 1900 MHz
[     1.022563] acpicpu0: P15: FFH, lat  10 us, pow 56000 mW, 1800 MHz
[     1.022563] acpicpu0: P16: FFH, lat  10 us, pow 54000 mW, 1700 MHz
[     1.022563] acpicpu0: P17: FFH, lat  10 us, pow 52000 mW, 1600 MHz
[     1.022563] acpicpu0: T0: FFH, lat   1 us, pow   672 mW, 100 %
[     1.022563] acpicpu0: T1: FFH, lat   1 us, pow   588 mW,  88 %
[     1.022563] acpicpu0: T2: FFH, lat   1 us, pow   504 mW,  75 %
[     1.022563] acpicpu0: T3: FFH, lat   1 us, pow   420 mW,  63 %
[     1.022563] acpicpu0: T4: FFH, lat   1 us, pow   336 mW,  50 %
[     1.022563] acpicpu0: T5: FFH, lat   1 us, pow   252 mW,  38 %
[     1.022563] acpicpu0: T6: FFH, lat   1 us, pow   168 mW,  25 %
[     1.022563] acpicpu0: T7: FFH, lat   1 us, pow    84 mW,  13 %
[     1.022563] coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=102
[     1.022563] acpicpu1 at cpu1: ACPI CPU
[     1.022563] coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=102
[     1.022563] acpicpu2 at cpu2: ACPI CPU
[     1.022563] acpicpu3 at cpu3: ACPI CPU
[     1.022563] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
[     2.042386] timecounter: Timecounter "TSC" frequency 3292696920 Hz quality 3000
[     2.052389] IPsec: Initialized Security Association Processing.
[     2.062392] uhub0 at usb0: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
[     2.062392] uhub0: 2 ports with 2 removable, self powered
[     2.062392] uhub1 at usb1: NetBSD (0000) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
[     2.062392] uhub1: 2 ports with 2 removable, self powered
[     2.152423] ahcisata1 port 5: device present, speed: 3.0Gb/s
[     2.152423] ahcisata1 port 0: device present, speed: 3.0Gb/s
[     2.152423] ahcisata1 port 4: device present, speed: 3.0Gb/s
[     2.752630] autoconfiguration error: ahcisata1 port 5: setting WDCTL_RST failed for drive 15
[     2.752630] autoconfiguration error: ahcisata1 port 4: setting WDCTL_RST failed for drive 15
[     3.252803] autoconfiguration error: ahcisata1 port 5: drive 15 reset failed, disabling PMP
[     3.252803] autoconfiguration error: ahcisata1 port 4: drive 15 reset failed, disabling PMP
[     3.352837] ahcisata1 port 5: device present, speed: 3.0Gb/s
[     3.352837] ahcisata1 port 4: device present, speed: 3.0Gb/s
[     4.313168] uhub2 at uhub0 port 1: vendor 8087 (0x8087) product 0024 (0x24), class 9/0, rev 2.00/0.00, addr 2
[     4.313168] uhub2: single transaction translator
[     4.313168] uhub3 at uhub1 port 1: vendor 8087 (0x8087) product 0024 (0x24), class 9/0, rev 2.00/0.00, addr 2
[     4.313168] uhub3: single transaction translator
[     4.313168] uhub2: 4 ports with 4 removable, self powered
[     4.313168] uhub3: 6 ports with 6 removable, self powered
[     5.253492] wd0 at atabus2 drive 0
[     5.253492] wd0: <ST380011A>
[     5.253492] wd0: drive supports 16-sector PIO transfers, LBA48 addressing
[     5.253492] wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
[     5.313513] wd0: 32-bit data port
[     5.313513] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
[     5.313513] wd0(jmide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
[     5.313513] wd1 at atabus3 drive 0
[     5.313513] wd1: <ST1000DM003-1ER162>
[     5.313513] wd1: drive supports 16-sector PIO transfers, LBA48 addressing
[     5.313513] wd1: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors
[     5.363530] wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags)
[     5.363530] wd1(ahcisata1:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags)
[     5.623620] uhub4 at uhub3 port 4: vendor 214b (0x214b) USB2.0 HUB (0x7000), class 9/0, rev 2.00/1.00, addr 3
[     5.623620] uhub4: single transaction translator
[     5.623620] uhub4: 4 ports with 4 removable, self powered
[     5.623620] uhidev0 at uhub2 port 1 configuration 1 interface 0
[     5.623620] uhidev0: Logitech (0x46d) USB Keyboard (0xc31c), rev 1.10/64.02, addr 3, iclass 3/1
[     5.633624] ukbd0 at uhidev0: 8 Variable keys, 6 Array codes
[     6.043765] wskbd0 at ukbd0: console keyboard
[     6.043765] uhidev1 at uhub2 port 1 configuration 1 interface 1
[     6.043765] uhidev1: Logitech (0x46d) USB Keyboard (0xc31c), rev 1.10/64.02, addr 3, iclass 3/0
[     6.043765] uhidev1: 5 report ids
[     6.043765] uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
[     6.043765] uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
[     6.043765] uhid2 at uhidev1 reportid 3: input=3, output=0, feature=0
[     6.043765] uhid3 at uhidev1 reportid 5: input=0, output=0, feature=5
[     6.934072] uhub5 at uhub4 port 3: vendor 214b (0x214b) USB2.0 HUB (0x7000), class 9/0, rev 2.00/1.00, addr 4
[     6.934072] uhub5: single transaction translator
[     6.934072] uhub5: 4 ports with 4 removable, self powered
[     7.014099] uhidev2 at uhub2 port 2 configuration 1 interface 0
[     7.014099] uhidev2: Logitech (0x46d) USB Optical Mouse (0xc077), rev 2.00/72.00, addr 4, iclass 3/1
[     7.014099] ums0 at uhidev2: 3 buttons and Z dir
[     7.014099] wsmouse0 at ums0 mux 0
[     7.324206] WARNING: 5 errors while detecting hardware; check system log.
[     7.324206] boot device: <unknown>
[     7.324206] root device: wd0a
[    12.596023] dump device (default wd0b): 
[    13.576361] file system (default generic): 
[    14.406647]  dumps on wd0b
[    14.436658] root file system type: ffs
[    14.446661] kern.module.path=/stand/amd64/9.99.46/modules
[    14.455004] kern info: [drm] initializing kernel modesetting (CAICOS 0x1002:0x6779 0x1682:0x3200).
[    14.455004] kern info: [drm] register mmio base: 0xfbec0000
[    14.455004] kern info: [drm] register mmio size: 131072
[    14.456665] kern info: ATOM BIOS: C28506
[    14.456665] radeon0: info: VRAM: 2048M 0x0000000000000000 - 0x000000007FFFFFFF (2048M used)
[    14.456665] radeon0: info: GTT: 1024M 0x0000000080000000 - 0x00000000BFFFFFFF
[    14.456665] kern info: [drm] Detected VRAM RAM=800M, BAR=256M
[    14.456665] kern info: [drm] RAM width 64bits DDR
[    14.456665] Zone  kernel: Available graphics memory: 1026908 kiB
[    14.456665] kern info: [drm] radeon: 2048M of VRAM memory ready
[    14.456665] kern info: [drm] radeon: 1024M of GTT memory ready.
[    14.456665] kern info: [drm] Loading CAICOS Microcode
[    14.486675] kern info: [drm] Internal thermal controller without fan control
[    14.496678] kern info: [drm] radeon: dpm initialized
[    14.506683] kern info: [drm] GART: num cpu pages 262144, num gpu pages 262144
[    14.536692] kern info: [drm] PCIE GART of 1024M enabled (table at 0x0000000000274000).
[    14.536692] radeon0: info: WB enabled
[    14.536692] radeon0: info: fence driver on ring 0 use gpu addr 0x0000000080000c00 and cpu addr 0x0xffff8c6bcfc2bc00
[    14.536692] radeon0: info: fence driver on ring 3 use gpu addr 0x0000000080000c0c and cpu addr 0x0xffff8c6bcfc2bc0c
[    14.546695] radeon0: info: fence driver on ring 5 use gpu addr 0x0000000000072118 and cpu addr 0x0xffffab8078b32118
[    14.546695] kern info: [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    14.546695] kern info: [drm] Driver supports precise vblank timestamp query.
[    14.546695] radeon0: info: radeon: MSI limited to 32-bit
[    14.546695] radeon0: info: radeon: using MSI.
[    14.546695] radeon0: interrupting at msi3 vec 0 (radeon0)
[    14.546695] kern info: [drm] radeon: irq initialized.
[    14.566702] kern info: [drm] ring test on 0 succeeded in 3 usecs
[    14.566702] kern info: [drm] ring test on 3 succeeded in 6 usecs
[    14.746764] kern info: [drm] ring test on 5 succeeded in 2 usecs
[    14.746764] kern info: [drm] UVD initialized successfully.
[    14.746764] kern info: [drm] ib test on ring 0 succeeded in 0 usecs
[    14.746764] kern info: [drm] ib test on ring 3 succeeded in 0 usecs
[    15.396989] kern info: [drm] ib test on ring 5 succeeded
[    15.396989] kern info: [drm] Radeon Display Connectors
[    15.396989] kern info: [drm] Connector 0:
[    15.396989] kern info: [drm]   HDMI-A-1
[    15.396989] kern info: [drm]   HPD4
[    15.396989] kern info: [drm]   DDC: 0x6460 0x6460 0x6464 0x6464 0x6468 0x6468 0x646c 0x646c
[    15.396989] kern info: [drm]   Encoders:
[    15.396989] kern info: [drm]     DFP1: INTERNAL_UNIPHY1
[    15.396989] kern info: [drm] Connector 1:
[    15.396989] kern info: [drm]   DVI-I-1
[    15.396989] kern info: [drm]   HPD1
[    15.396989] kern info: [drm]   DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[    15.396989] kern info: [drm]   Encoders:
[    15.396989] kern info: [drm]     DFP2: INTERNAL_UNIPHY
[    15.396989] kern info: [drm] Connector 2:
[    15.396989] kern info: [drm]   VGA-1
[    15.396989] kern info: [drm]   DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c 0x644c
[    15.396989] kern info: [drm]   Encoders:
[    15.396989] kern info: [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[    15.507026] radeondrmkmsfb0 at radeon0
[    15.517030] radeondrmkmsfb0: framebuffer at 0xffffab807915e000, size 1920x1200, depth 32, stride 7680
[    15.677085] no data for est. mode 640x480x67
[    15.697092] wsdisplay0 at radeondrmkmsfb0 kbdmux 1: console (default, vt100 emulation), using wskbd0
[    15.740178] wsmux1: connecting to wsdisplay0
[    15.757113] init path (default /sbin/init): 
[    15.908048] init: trying /sbin/init
...
Follow-Ups:
- Re: configuring raid using gpt, large drives
  - From: MLH
- Re: configuring raid using gpt, large drives
  - From: Michael van Elst
References:
- Re: configuring raid using gpt, large drives
  - From: Emmanuel Dreyfus
Prev by Date: Re: ZFS on root - almost there
Next by Date: Re: configuring raid using gpt, large drives
Previous by Thread: Re: configuring raid using gpt, large drives
Next by Thread: Re: configuring raid using gpt, large drives
Indexes:
Home | Main Index | Thread Index | Old Index