Current-Users archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: Pinebook and NetBSD 8.99.39 [UPDATE]
Well... I did both
arm64# dd if=arm64.img of=/dev/rld2c bs=1m conv=sync
dd: /dev/rld2c: Input/output error
30+0 records in
29+0 records out
30408704 bytes transferred in 9.927 secs (3063231 bytes/sec)
And
arm64# dd if=NetBSD-evbarm-aarch64-201905120950Z-pinebook.img of=/dev/rld2c bs=1m conv=sync
dd: /dev/rld2c: Input/output error
30+0 records in
29+0 records out
30408704 bytes transferred in 11.143 secs (2728951 bytes/sec)
Both commands generated a ton of "ld2c: error writing fsbn..." errors. When I reboot I get a blank screen. ( Any thoughts on what I can do?
Disklabel looks like this:
arm64# disklabel ld2
# /dev/rld2:
type: ld
disk: ld2
label: default label
flags:
bytes/sector: 512
sectors/track: 63
tracks/cylinder: 32
sectors/cylinder: 2016
cylinders: 1040
total sectors: 2097152
rpm: 3600
interleave: 1
trackskew: 0
cylinderskew: 0
headswitch: 0 # microseconds
track-to-track seek: 0 # microseconds
drivedata: 0
5 partitions:
# size offset fstype [fsize bsize cpg/sgs]
c: 2097152 0 4.2BSD 0 0 0 # (Cyl. 0 - 1040*)
e: 163840 32768 MSDOS # (Cyl. 16*- 97*)
disklabel: boot block size 0
disklabel: super block size 0
disklabel: partitions c and e overlap
I will surmise that overlapping partitions are not good?
On 5/14/19, 12:53 PM, "Jason Thorpe" <thorpej%me.com@localhost> wrote:
> On May 14, 2019, at 9:33 AM, Ron Georgia <netverbs%gmail.com@localhost> wrote:
>
> If I understand correctly:
> 1. boot Pinebook from microSD loaded with Pinebook NetBSD ARM Bootable Images from https://www.invisible.ca/arm/
> 2. download arm64.img from ftp://nyftp.netbsd.org/pub/NetBSD-daily/HEAD/201905140810Z/evbarm-aarch64/binary/gzimg/ to microSD card.
You can dd the invisible.ca imagine to the eMMC as well. It's just a standard arm64.img with u-boot helpfully added by Jared; no need to download a second one (to which you would then need to add u-boot).
> 3. dd image to /dev/rld2c
> 4. Power down, remove SD card and reboot.
>
> Correct?
> For YES, press 1
> For NO, press 2
>
> On 5/14/19, 10:15 AM, "Jared McNeill" <jmcneill%invisible.ca@localhost> wrote:
>
> Easiest way is to download the image to the SD card, then dd it to the
> eMMC:
>
> # dd if=arm64.img of=/dev/rld2c bs=1m conv=sync
>
> You can't "wreck" your Pinebook this way as it will always try to boot
> from SD card first. So after writing the image to eMMC, shutdown the
> computer, remove the SD card, and power it back on. If something goes
> wrong, plug the SD card back in and it will boot from that device when you
> power it back on.
>
>
> On Tue, 14 May 2019, Ron Georgia wrote:
>
>> Instead of creating the image with dd, I followed the suggestion of building the image with "highly recommend" Etcher. I am now able to login as root! Not sure what happened. I am documenting every step of the way in order to make my journey, mistakes and all, available to other "not so savvy" Pinebook users.
>>
>> How do I install NetBSD directly onto my Pinebook? Do I use sysinst (per https://wiki.netbsd.org/ports/evbarm/install_using_sysinst/)?
>> Before I "wreck" my Pinebook, do I select ld2 as the drive to partition and install?
>>
>> =========== MISC DATA ===========
>> arm64# disklabel ld0
>> # /dev/rld0:
>> type: SCSI
>> disk: STORAGE DEVICE
>> label: fictitious
>> flags: removable
>> bytes/sector: 512
>> sectors/track: 32
>> tracks/cylinder: 64
>> sectors/cylinder: 2048
>> cylinders: 1641
>> total sectors: 31116288
>> rpm: 3600
>> interleave: 1
>> trackskew: 0
>> cylinderskew: 0
>> headswitch: 0 # microseconds
>> track-to-track seek: 0 # microseconds
>> drivedata: 0
>>
>> 8 partitions:
>> # size offset fstype [fsize bsize cpg/sgs]
>> a: 30657536 458752 4.2BSD 0 0 0 # (Cyl. 224 - 15193*)
>> b: 262144 196608 swap # (Cyl. 96 - 223)
>> c: 31116288 0 unused 0 0 # (Cyl. 0 - 15193*)
>> d: 31116288 0 unused 0 0 # (Cyl. 0 - 15193*)
>> e: 163840 32768 MSDOS # (Cyl. 16 - 95)
>>
>> arm64# disklabel ld2
>> # /dev/rld2:
>> type: ld
>> disk: ld2
>> label: default label
>> flags:
>> bytes/sector: 512
>> sectors/track: 63
>> tracks/cylinder: 32
>> sectors/cylinder: 2016
>> cylinders: 1040
>> total sectors: 2097152
>> rpm: 3600
>> interleave: 1
>> trackskew: 0
>> cylinderskew: 0
>> headswitch: 0 # microseconds
>> track-to-track seek: 0 # microseconds
>> drivedata: 0
>>
>> 3 partitions:
>> # size offset fstype [fsize bsize cpg/sgs]
>> a: 2097152 0 4.2BSD 0 0 0 # (Cyl. 0 - 1040*)
>> c: 2097152 0 4.2BSD 0 0 0 # (Cyl. 0 - 1040*)
>> disklabel: boot block size 0
>> disklabel: super block size 0
>> disklabel: partitions a and c overlap
>>
>> arm64# gpt show ld0
>> GPT not found, displaying data from MBR.
>>
>> start size index contents
>> 0 1 MBR
>> 1 32767 Unused
>> 32768 163840 1 MBR part 12 (active)
>> 196608 262144 Unused
>> 458752 30657536 2 MBR part 169
>>
>> arm64# gpt show ld2
>> gpt: /dev/rld2: map entry doesn't fit media: new start + new size < start + size
>> (1 + 1fffff < a000 + 1d50000)
>>
>> arm64# dmesg | grep ld
>> [ 1.000016] axpreg5 at axppmic0: eldo2
>> [ 2.737735] sdmmc1: autoconfiguration error: couldn't enable card: 60
>> [ 2.811871] ld2 at sdmmc2: <0x45:0x0100:DF4016:0x00:0xfe875b0b:0x000>
>> [ 2.811871] ld2: 1024 MB, 1040 cyl, 32 head, 63 sec, 512 bytes/sect x 2097152 sectors
>> [ 2.828746] ld0 at sdmmc0: <0x03:0x5344:SS16G:0x80:0x42ce3d51:0x122>
>> [ 2.848748] ld0: 15193 MB, 7717 cyl, 64 head, 63 sec, 512 bytes/sect x 31116288 sectors
>> [ 2.848748] ld2: mbr partition exceeds disk size
>> [ 2.848748] ld2: 8-bit width, 200.000 MHz
>> [ 2.876482] ld0: 4-bit width, High-Speed/SDR25, 50.000 MHz
>> [ 7.617842] ld2: mbr partition exceeds disk size
>> [ 7.627841] boot device: ld0
>> [ 7.627841] root on ld0a dumps on ld0b
>> [ 424.699875] ld2: mbr partition exceeds disk size
>> [ 424.709875] ld2: mbr partition exceeds disk size
>> [ 431.049997] ld2: mbr partition exceeds disk size
>> [ 431.059997] ld2: mbr partition exceeds disk size
>> [ 431.059997] ld2: mbr partition exceeds disk size
>> [ 431.149999] ld2: mbr partition exceeds disk size
>> [ 442.320213] ld2: mbr partition exceeds disk size
>> [ 746.325984] ld2: mbr partition exceeds disk size
>> [ 746.335984] ld2: mbr partition exceeds disk size
>> [ 1592.422047] ld2: mbr partition exceeds disk size
>> [ 1592.422047] ld2: mbr partition exceeds disk size
>> [ 1679.653695] ld2: mbr partition exceeds disk size
>> [ 1679.673697] ld2: mbr partition exceeds disk size
>> [ 1684.513788] ld2: mbr partition exceeds disk size
>> [ 1684.513788] ld2: mbr partition exceeds disk size
>> [ 1684.563793] ld2: mbr partition exceeds disk size
>> [ 1684.583793] ld2: mbr partition exceeds disk size
>> [ 1684.583793] ld2: mbr partition exceeds disk size
>> [ 1761.785290] ld2: mbr partition exceeds disk size
>> [ 1778.945617] ld2: mbr partition exceeds disk size
>> [ 1993.819664] ld2: mbr partition exceeds disk size
>>
>> arm64# mount
>> /dev/ld0a on / type ffs (noatime, local)
>> /dev/ld0e on /boot type msdos (local)
>> kernfs on /kern type kernfs (local)
>> ptyfs on /dev/pts type ptyfs (local)
>> procfs on /proc type procfs (local)
>> tmpfs on /var/shm type tmpfs (local)
>>
>> # sysinst
>> ========================================
>> What kind of system do you have?
>>
>> a: Raspberry PI
>>> b: Other
>>
>> ========================================
>> NetBSD/evbarm 8.99.39
>>
>> This menu-driven tool is designed to help you install NetBSD to a hard disk, or upgrade an existing
>> NetBSD system, with a minimum of work.
>> In the following menus type the reference letter (a, b, c, ...) to select an item, or type
>> CTRL+N/CTRL+P to select the next/previous item.
>> The arrow keys and Page-up/Page-down may also work.
>> Activate the current selection from the menu by typing the enter key.
>>
>> If you booted from a floppy, you may now remove the disk.
>> Thank you for using NetBSD!
>>
>> NetBSD-8.99.39 Install System
>>
>>> a: Install NetBSD to hard disk
>> b: Upgrade NetBSD on a hard disk
>> c: Re-install sets or install additional sets
>> d: Reboot the computer
>> e: Utility menu
>> f: Config menu
>> x: Exit Install System
>>
>> ========================================
>> On which disk do you want to install NetBSD?
>>
>> ┌──────────────────────────┐
>> │ Available disks │
>> │ │
>> │>a: ld2 │
>> │ b: Extended partitioning │
>> │ x: Exit │
>> └──────────────────────────┘
>> ========================================
>>
>> I do not see ld0.
>>
>> On 5/14/19, 8:59 AM, "Ron Georgia" <netverbs%gmail.com@localhost> wrote:
>>
>> I just received my new 1080P 11inch (27.94 cm) Pinebook. It was pre-loaded with Ubuntu and KDE. While I like KDE, it seems a bit heavy. Ubuntu is ... ok, but I would rather have NetBSD and LXDE or Mate. I attempted to install NetBSD but ran into some problems. Most likely due to my incomplete understanding (see tag line below).
>>
>> 1. I downloaded the Pinebook image (NetBSD-evbarm-aarch64-201905120950Z-pinebook.img) from https://www.invisible.ca/arm/
>> 2. dd the image to my microSD card.
>> 3. Inserted the micro SD into the SD slot of the Pinebook and booted.
>>
>> The first boot ended in a ==> prompt. Not sure what that was all about.
>> Reboot produced the NetBSD "arm" boot processes; however, there was a problem. When presented with the login prompt I tried to type "root" but the right side of the keyboard acts like a number pad. Pressing "o" gives me the escape sequence for a "6" without the numlock engaged. Pressing shift "o" gets me a capital O while Fn + o gets me a "6."
>>
>> Questions:
>> 1. Is there a way to make the keyboard a standard keyboard?
>> 2. Once booted, now do I "reflash" the internal drive to boot NetBSD without having to boot from the micro SD card?
>>
>>
>> Ron Georgia
>> “90% of my problems are due to ignorance, the other 10% is because I just don’t know any better.”
>>
>>
>>
>>
>>
>>
>>
>
>
-- thorpej
Home |
Main Index |
Thread Index |
Old Index