Current-Users archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

Re: dmesg spam: ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051



The TFD 0x2051 corresponds to Media Changed error, with DRDY/ERR status bits. Is it possible this message appears every time you change media in the cd0? 

Alternatively, I imagine this could be generated if the drive is setup to hibernate/suspend.

Jaromir

2017-11-10 10:49 GMT+01:00 <stefan@hertenberger.bayern>:
Am 2017-11-10 10:22, schrieb Martin Husemann:
On Fri, Nov 10, 2017 at 10:11:43AM +0100, stefan@hertenberger.bayern wrote:
Am 2017-11-10 09:57, schrieb Martin Husemann:
> Can you show the dmesg part describing your ahcisata devices?

ahcisata0 at pci0 dev 31 function 2: vendor 8086 product 1c03 (rev. 0x04)
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.30, 6 ports, 32 slots, CAP
0xef30ff45<EMS,PSC,SSC,PMD,ISS=0x3=Gen3,SCLO,SAL,SALP,SSS,SSNTF,SNCQ,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1

And the device at atabus1?

Martin

The complete dmesg out put was attached on the first mail.

Regards Stefan

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 8.99.6 (GENERIC) #8: Thu Nov  9 23:16:37 UTC 2017
        root@packard:/usr/build/obj/sys/arch/amd64/compile/GENERIC
total memory = 8043 MB
avail memory = 7788 MB
rnd: seeded with 128 bits
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
running cgd selftest aes-xts-256 aes-xts-512 done
RTC BIOS diagnostic error 0x80<clock_battery>
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Packard Bell EasyNote TS11HR (V1.20)
mainbus0 (root)
ACPI: RSDP 0x00000000000FE020 000024 (v02 ACRSYS)
ACPI: XSDT 0x0000000096FFE120 00007C (v01 ACRSYS ACRPRDCT 00000001      01000013)
ACPI: FACP 0x0000000096FFC000 0000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: DSDT 0x0000000096FF0000 008F53 (v01 ACRSYS ACRPRDCT 00000000 1025 00040000)
ACPI: FACS 0x0000000096F6D000 000040
ACPI: ASF! 0x0000000096FFD000 0000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: HPET 0x0000000096FFB000 000038 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: APIC 0x0000000096FFA000 00008C (v02 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: MCFG 0x0000000096FF9000 00003C (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: SLIC 0x0000000096FEF000 000176 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: SSDT 0x0000000096FEE000 000BC2 (v01 ACRSYS ACRPRDCT 00001000 1025 00040000)
ACPI: BOOT 0x0000000096FEC000 000028 (v01 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: ASPT 0x0000000096FE9000 000034 (v07 ACRSYS ACRPRDCT 00000001 1025 00040000)
ACPI: SSDT 0x0000000096FE8000 00090C (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
ACPI: SSDT 0x0000000096FE7000 000996 (v01 ACRSYS ACRPRDCT 00003000 1025 00040000)
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: 4 ACPI AML tables successfully acquired and loaded
ioapic0 at mainbus0 apid 0: pa 0xfec00000, version 0x20, 24 pins
cpu0 at mainbus0 apid 0
cpu0: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7
cpu0: package 0, core 0, smt 0
cpu1 at mainbus0 apid 1
cpu1: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7
cpu1: package 0, core 0, smt 1
cpu2 at mainbus0 apid 2
cpu2: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7
cpu2: package 0, core 1, smt 0
cpu3 at mainbus0 apid 3
cpu3: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7
cpu3: package 0, core 1, smt 1
cpu4 at mainbus0 apid 4
cpu4: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7
cpu4: package 0, core 2, smt 0
cpu5 at mainbus0 apid 5
cpu5: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7
cpu5: package 0, core 2, smt 1
cpu6 at mainbus0 apid 6
cpu6: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7
cpu6: package 0, core 3, smt 0
cpu7 at mainbus0 apid 7
cpu7: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz, id 0x206a7
cpu7: package 0, core 3, smt 1
acpi0 at mainbus0: Intel ACPICA 20170831
acpi0: X/RSDT: OemId <ACRSYS,ACRPRDCT,00000001>, AslId <    ,01000013>
acpi0: MCFG: segment 0, bus 0-255, address 0x00000000e0000000
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFE4010E761810 00067C (v01 PmRef  Cpu0Cst  00003001 INTL 20100121)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFE4025DC6F410 000303 (v01 PmRef  ApIst    00003000 INTL 20100121)
ACPI: Dynamic OEM Table Load:
ACPI: SSDT 0xFFFFE4010E6915D0 000119 (v01 PmRef  ApCst    00003000 INTL 20100121)
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
acpiec0 at acpi0 (EC0, PNP0C09): io 0x62,0x66
FWHD (INT0800) at acpi0 not configured
LDRC (PNP0C02) at acpi0 not configured
attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
CWDT (INT3F0D) at acpi0 not configured
pckbc1 at acpi0 (KBC0, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (MSS0, SYN1B16) (aux port): irq 12
acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (BAT0, PNP0C0A-1): ACPI Battery
acpibat0: Simplo  Lion rechargeable battery
acpibat0: granularity: low->warn 0.264 Ah, warn->full 3.780 Ah
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
acpilid0 at acpi0 (LID0, PNP0C0D): ACPI Lid Switch
acpibut1 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
acpiwmi0 at acpi0 (WMID, PNP0C14-APGe): ACPI WMI Interface
acpiwmibus at acpiwmi0 not configured
acpiwmi1 at acpi0 (CWMI, PNP0C14-COMP): ACPI WMI Interface
acpiwmibus at acpiwmi1 not configured
PDRC (PNP0C02) at acpi0 not configured
acpivga0 at acpi0 (GFX0): ACPI Display Adapter
acpiout0 at acpivga0 (DD01, 0x0100): ACPI Display Output Device
acpiout1 at acpivga0 (DD02, 0x0240): ACPI Display Output Device
acpiout2 at acpivga0 (DD03, 0x0410): ACPI Display Output Device
acpiout2: brightness levels: [10,20,30,40,50,60,70,80,90,100]
acpiout3 at acpivga0 (DD04, 0x7330): ACPI Display Output Device
acpiout4 at acpivga0 (DD05, 0x0005): ACPI Display Output Device
acpiout5 at acpivga0 (DD06, 0x0006): ACPI Display Output Device
acpiout6 at acpivga0 (DD07, 0x0007): ACPI Display Output Device
acpiout7 at acpivga0 (DD08, 0x0008): ACPI Display Output Device
acpivga0: unknown output device acpiout4
acpivga0: unknown output device acpiout5
acpivga0: unknown output device acpiout6
acpivga0: unknown output device acpiout7
acpivga0: connected output devices:
acpivga0:   0x0100 (acpiout0): VGA Analog Monitor, index 0, port 0, head 0
acpivga0:   0x0240 (acpiout1): TV/HDTV Monitor, index 0, port 4, head 0
acpivga0:   0x0410 (acpiout2): Int. Digital Flat Panel, index 0, port 1, head 0
acpivga0:   0x7330 (acpiout3): Ext. Digital Monitor, index 0, port 3, head 0
MEM2 (PNP0C01) at acpi0 not configured
PTID (INT340E) at acpi0 not configured
ACPI: Enabled 9 GPEs in block 00 to 3F
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pms0: Synaptics touchpad version 7.5
pms0: Extended W mode, Palm detect, Multi-finger Report, Multi-finger
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 8086 product 0104 (rev. 0x09)
i915drmkms0 at pci0 dev 2 function 0: vendor 8086 product 0116 (rev. 0x09)
drm: Memory usable by graphics device = 2048M
drm: Supports vblank timestamp caching Rev 2 (21.10.2013).
drm: Driver supports precise vblank timestamp query.
i915drmkms0: interrupting at ioapic0 pin 16 (i915)
drm: Wrong MCH_SSKPD value: 0x16040307
drm: This can cause pipe underruns and display issues.
drm: Please upgrade your BIOS to fix this.
intelfb0 at i915drmkms0
i915drmkms0: info: registered panic notifier
intelfb0: framebuffer at 0xffff80008d70e000, size 1366x768, depth 32, stride 5504
wsdisplay0 at intelfb0 kbdmux 1: console (default, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
vendor 8086 product 1c3a (miscellaneous communications, revision 0x04) at pci0 dev 22 function 0 not configured
ehci0 at pci0 dev 26 function 0: vendor 8086 product 1c2d (rev. 0x04)
ehci0: interrupting at ioapic0 pin 16
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
usb0 at ehci0: USB revision 2.0
hdaudio0 at pci0 dev 27 function 0: HD Audio Controller
hdaudio0: interrupting at msi0 vec 0
hdafg0 at hdaudio0: vendor 10ec product 0269
hdafg0: DAC00 2ch: Speaker [Built-In], HP Out [Jack]
hdafg0: ADC01 2ch: Mic In [Built-In]
hdafg0: ADC02 2ch: Mic In [Jack]
hdafg0: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, mmap, independent
hdafg0: Virtual format configured - Format SLINEAR, precision 16, channels 2, frequency 48000
hdafg0: Latency: 128 milliseconds
spkr0 at audio0: PC Speaker (synthesized)
wsbell at spkr0 not configured
hdafg1 at hdaudio0: vendor 8086 product 2805
hdafg1: DP00 8ch: Digital Out [Jack]
hdafg1: 8ch/0ch 48000Hz PCM16*
ppb0 at pci0 dev 28 function 0: vendor 8086 product 1c10 (rev. 0xb4)
ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
ppb0: link is x1 @ 2.5GT/s
pci1 at ppb0 bus 2
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci1 dev 0 function 0: Broadcom BCM57785 Gigabit Ethernet
bge0: interrupting at msi1 vec 0
bge0: HW config 000a0154, 00004004, 00000008, 00000000 00000000
bge0: ASIC BCM57765 B0 (0x57785100), Ethernet address b8:70:f4:a1:34:91
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM57765 1000BASE-T media interface, rev. 4
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
sdhc0 at pci1 dev 0 function 1: vendor 14e4 product 16bc (rev. 0x10)
sdhc0: interrupting at ioapic0 pin 17
sdhc0: SDHC 2.0, rev 21, SDMA, 50000 kHz, HS 1.8V 3.0V 3.3V, 2048 byte blocks
sdmmc0 at sdhc0 slot 0
vendor 14e4 product 16be (miscellaneous system, revision 0x10) at pci1 dev 0 function 2 not configured
vendor 14e4 product 16bf (miscellaneous system, revision 0x10) at pci1 dev 0 function 3 not configured
ppb1 at pci0 dev 28 function 1: vendor 8086 product 1c12 (rev. 0xb4)
ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
ppb1: link is x1 @ 2.5GT/s
pci2 at ppb1 bus 3
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
athn0 at pci2 dev 0 function 0: Atheros AR9287
athn0: rev 2 (2T2R), ROM rev 4, address 68:a3:c4:d8:95:d8
athn0: interrupting at ioapic0 pin 17
athn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
athn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ppb2 at pci0 dev 28 function 3: vendor 8086 product 1c16 (rev. 0xb4)
ppb2: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
pci3 at ppb2 bus 5
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
xhci0 at pci3 dev 0 function 0: vendor 1033 product 0194 (rev. 0x04)
xhci0: interrupting at msi2 vec 0
xhci0: xHCI version 0.96
usb1 at xhci0: USB revision 3.0
usb2 at xhci0: USB revision 2.0
ehci1 at pci0 dev 29 function 0: vendor 8086 product 1c26 (rev. 0x04)
ehci1: interrupting at ioapic0 pin 23
ehci1: BIOS has given up ownership
ehci1: EHCI version 1.0
usb3 at ehci1: USB revision 2.0
ichlpcib0 at pci0 dev 31 function 0: vendor 8086 product 1c49 (rev. 0x04)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
tco0 at ichlpcib0: TCO (watchdog) timer configured.
tco0: Min/Max interval 1/367 seconds
ahcisata0 at pci0 dev 31 function 2: vendor 8086 product 1c03 (rev. 0x04)
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.30, 6 ports, 32 slots, CAP 0xef30ff45<EMS,PSC,SSC,PMD,ISS=0x3=Gen3,SCLO,SAL,SALP,SSS,SSNTF,SNCQ,S64A>
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 8086 product 1c22 (rev. 0x04)
ichsmb0: interrupting at ioapic0 pin 19
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
pcppi0 at isa0 port 0x61
spkr1 at pcppi0: PC Speaker
wsbell at spkr1 not configured
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
attimer1: attached to pcppi0
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat   1 us, pow  1000 mW
acpicpu0: C3: FFH, lat 104 us, pow   350 mW
acpicpu0: P0: FFH, lat  10 us, pow 45000 mW, 2001 MHz, turbo boost
acpicpu0: P1: FFH, lat  10 us, pow 45000 mW, 2000 MHz
acpicpu0: P2: FFH, lat  10 us, pow 42264 mW, 1900 MHz
acpicpu0: P3: FFH, lat  10 us, pow 39581 mW, 1800 MHz
acpicpu0: P4: FFH, lat  10 us, pow 36953 mW, 1700 MHz
acpicpu0: P5: FFH, lat  10 us, pow 34377 mW, 1600 MHz
acpicpu0: P6: FFH, lat  10 us, pow 31853 mW, 1500 MHz
acpicpu0: P7: FFH, lat  10 us, pow 29388 mW, 1400 MHz
acpicpu0: P8: FFH, lat  10 us, pow 26968 mW, 1300 MHz
acpicpu0: P9: FFH, lat  10 us, pow 24598 mW, 1200 MHz
acpicpu0: P10: FFH, lat  10 us, pow 22280 mW, 1100 MHz
acpicpu0: P11: FFH, lat  10 us, pow 20012 mW, 1000 MHz
acpicpu0: P12: FFH, lat  10 us, pow 17797 mW,  900 MHz
acpicpu0: P13: FFH, lat  10 us, pow 15628 mW,  800 MHz
acpicpu0: T0: I/O, lat   1 us, pow     0 mW, 100 %
acpicpu0: T1: I/O, lat   1 us, pow     0 mW,  88 %
acpicpu0: T2: I/O, lat   1 us, pow     0 mW,  76 %
acpicpu0: T3: I/O, lat   1 us, pow     0 mW,  64 %
acpicpu0: T4: I/O, lat   1 us, pow     0 mW,  52 %
acpicpu0: T5: I/O, lat   1 us, pow     0 mW,  40 %
acpicpu0: T6: I/O, lat   1 us, pow     0 mW,  28 %
acpicpu0: T7: I/O, lat   1 us, pow     0 mW,  16 %
coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100
acpicpu1 at cpu1: ACPI CPU
acpicpu2 at cpu2: ACPI CPU
coretemp1 at cpu2: thermal sensor, 1 C resolution, Tjmax=100
acpicpu3 at cpu3: ACPI CPU
acpicpu4 at cpu4: ACPI CPU
coretemp2 at cpu4: thermal sensor, 1 C resolution, Tjmax=100
acpicpu5 at cpu5: ACPI CPU
acpicpu6 at cpu6: ACPI CPU
coretemp3 at cpu6: thermal sensor, 1 C resolution, Tjmax=100
acpicpu7 at cpu7: ACPI CPU
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 1995574920 Hz quality 3000
uhub0 at usb1: vendor 1033 (0x1033) xHCI Root Hub (0000), class 9/0, rev 1.00/1.00, addr 0
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb2: vendor 1033 (0x1033) xHCI Root Hub (0000), class 9/0, rev 2.00/1.00, addr 0
uhub1: 2 ports with 2 removable, self powered
IPsec: Initialized Security Association Processing.
uhub2 at usb0: vendor 8086 (0x8086) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 8086 (0x8086) EHCI root hub (0000), class 9/0, rev 2.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ahcisata0 port 0: device present, speed: 3.0Gb/s
ahcisata0 port 1: device present, speed: 1.5Gb/s
acpiacad0: AC adapter online.
drm: Enabling RC6 states: RC6 on, RC6p off, RC6pp off
wd0 at atabus0 drive 0
wd0: <WDC WD3200BEKT-00F3T0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags)
atapibus0 at atabus1: 1 targets
cd0 at atapibus0 drive 0: <PIONEER DVD-RW DVRTD10RS, SCB1403891, 1.00> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
uhub4 at uhub3 port 1: vendor 8087 (0x8087) product 0024 (0x24), class 9/0, rev 2.00/0.00, addr 2
uhub4: single transaction translator
uhub4: 6 ports with 6 removable, self powered
uhub5 at uhub2 port 1: vendor 8087 (0x8087) product 0024 (0x24), class 9/0, rev 2.00/0.00, addr 2
uhub5: single transaction translator
uhub5: 6 ports with 6 removable, self powered
uhidev0 at uhub4 port 2 configuration 1 interface 0
uhidev0: Logitech (0x46d) USB Receiver (0xc52f), rev 2.00/30.00, addr 3, iclass 3/1
ums0 at uhidev0: 16 buttons, W and Z dirs
wsmouse1 at ums0 mux 0
uhidev1 at uhub4 port 2 configuration 1 interface 1
uhidev1: Logitech (0x46d) USB Receiver (0xc52f), rev 2.00/30.00, addr 3, iclass 3/0
uhidev1: 17 report ids
uhid0 at uhidev1 reportid 3: input=4, output=0, feature=0
uhid1 at uhidev1 reportid 16: input=6, output=6, feature=0
uhid2 at uhidev1 reportid 17: input=19, output=19, feature=0
uvideo0 at uhub5 port 3 configuration 1 interface 0: AAB5R0114 (0x58f) 1.3M HD WebCam (0xb002), rev 2.00/0.02, addr 3
video0 at uvideo0: AAB5R0114 (0x58f) 1.3M HD WebCam (0xb002), rev 2.00/0.02, addr 3
urtwn0 at uhub4 port 4
urtwn0: Realtek (0x7392) 802.11n WLAN Adapter (0x7811), rev 2.00/2.00, addr 4
urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R, address 74:da:38:88:7c:ad
urtwn0: 1 rx pipe, 2 tx pipes
urtwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
urtwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
WARNING: 4 errors while detecting hardware; check system log.
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
kern.module.path=/stand/amd64/8.99.6/modules
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
acpibat0: normal capacity on 'charge state'
wsdisplay0: screen 1 added (default, vt100 emulation)
wsdisplay0: screen 2 added (default, vt100 emulation)
wsdisplay0: screen 3 added (default, vt100 emulation)
wsdisplay0: screen 4 added (default, vt100 emulation)

ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051
ahcisata0 port 1: active 2 is 0x40000001 tfd 0x2051



Home | Main Index | Thread Index | Old Index