SOLVED (maybe?) Re: Can't configure new disk

[pimin inwa <pimininca%gmail.com@localhost>]

On Wed, Mar 1, 2017 at 12:59 PM, pimin inwa <pimininca%gmail.com@localhost> wrote:

Running:

NetBSD gemini.wan.vpn 6.99.31 NetBSD 6.99.31 (GEMINI) #0: Sun Feb 16 19:11:21 PST 2014  root@:/usr/src/BUILD_OBJ/sys/arch/i386/compile/GEMINI i386

From boot.dmesg I see:

wd0 at atabus4 drive 0

wd0: <ST31000528AS>

wd0: drive supports 16-sector PIO transfers, LBA48 addressing

wd0: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors

wd0: 32-bit data port

wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)

wd1 at atabus4 drive 1

wd1: <Hitachi HDS721010CLA332>

wd1: drive supports 16-sector PIO transfers, LBA48 addressing

wd1: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors

wd1: 32-bit data port

wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)

wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)

wd1(piixide0:0:1): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)

boot device: wd0

root on wd0a dumps on wd0b

I can't run fdisk, disklabel, etc ... because wd1d isn't configured?   ls shows:

# ls -l /dev/wd1*

brw-r-----  1 root  operator  0,      8 Feb  1  2014 /dev/wd1a

brw-r-----  1 root  operator  0,      9 Feb  1  2014 /dev/wd1b

brw-r-----  1 root  operator  0,     10 Feb  1  2014 /dev/wd1c

brw-r-----  1 root  operator  0,     11 Feb  1  2014 /dev/wd1d

brw-r-----  1 root  operator  0,     12 Feb  1  2014 /dev/wd1e

brw-r-----  1 root  operator  0,     13 Feb  1  2014 /dev/wd1f

brw-r-----  1 root  operator  0,     14 Feb  1  2014 /dev/wd1g

brw-r-----  1 root  operator  0,     15 Feb  1  2014 /dev/wd1h

brw-r-----  1 root  operator  0, 524296 Feb  1  2014 /dev/wd1i

brw-r-----  1 root  operator  0, 524297 Feb  1  2014 /dev/wd1j

brw-r-----  1 root  operator  0, 524298 Feb  1  2014 /dev/wd1k

brw-r-----  1 root  operator  0, 524299 Feb  1  2014 /dev/wd1l

brw-r-----  1 root  operator  0, 524300 Feb  1  2014 /dev/wd1m

brw-r-----  1 root  operator  0, 524301 Feb  1  2014 /dev/wd1n

brw-r-----  1 root  operator  0, 524302 Feb  1  2014 /dev/wd1o

brw-r-----  1 root  operator  0, 524303 Feb  1  2014 /dev/wd1p

What am I forgetting to do?

Thanks,

Paul

DUMB! DUMB! Me.  The drive was plugged into a HighPoint (Promise?) card.  Plugging the SSD into the motherboard SATA adapter and it is now recognized.  The add-on card seems to be IDE only??  Although the previous drives plugged into that card claim to be SATA.  

Thanks for all the help.

Paul