Re: Problems

[Donald Allen <donaldcallen%gmail.com@localhost>]

On Sat, Nov 20, 2010 at 10:45 PM, John Nemeth 
<jnemeth%victoria.tc.ca@localhost> wrote:
> On Apr 12,  9:42am, Donald Allen wrote:
> }
> } I am attempting to install the 5.1 release on an old Thinkpad 600x,
> } using boot.iso. When I booted from the CD, I happened to have a 3com
> } (Atheros-based) wireless card in a pcmcia slot, hoping to use it for a
> } network install. As the install kernel was booting:
> }
> } ath0 at cardburst function0
> } uvm_fault(0xc0b82a00,0,1)->0xe
> } uvm_fault(0xc0b82a00,0,1)->0xe
> } fatal page fault in supervisor mode
> }
> } If I remove the card, the install kernel boots. If I insert the card
> } while it is running, I get the same crash.
>
>     Can you post your dmesg, please?

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1 (GENERIC) #0: Sun Nov  7 14:39:56 UTC 2010
        
builds%b6.netbsd.org@localhost:/home/builds/ab/netbsd-5-1-RELEASE/i386/201011061943Z-obj/home/builds/ab/netbsd-5-1-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 575 MB
avail memory = 553 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
IBM 26455GU (Not Available)
mainbus0 (root)
cpu0 at mainbus0: Intel 686-class, 647MHz, id 0x681
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <IBM   ,TP600X  ,00000001>, AslId <    ,00000000>
LNKA: ACPI: Found matching pin for 0.2.INTA at func 0: 11
LNKB: ACPI: Found matching pin for 0.2.INTB at func 1: 11
LNKC: ACPI: Found matching pin for 0.3.INTA at func 0: 11
LNKA: ACPI: Found matching pin for 0.6.INTA at func 0: 11
LNKA: ACPI: Found matching pin for 1.0.INTA at func 0: 11
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 24-bit timer
acpilid0 at acpi0 (LID0, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
FDC0 (PNP0700) at acpi0 not configured
attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (MPRC, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
pckbc1 at acpi0 (KBD0, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (MOU0, IBM3780) (aux port): irq 12
acpiec0 at acpi0 (EC0, PNP0C09): io 0x62,0x66
acpiec0: using global ACPI lock
acpibat0 at acpi0 (BAT0, PNP0C0A-0): ACPI Battery (Control Method)
acpibat0: battery info: IBM Corporation , LION, ThinkPad Battery
acpiacad0 at acpi0 (AC, ACPI0003-0): ACPI AC Adapter
FN00 (PNP0C0B) at acpi0 not configured
FN20 (PNP0C0B) at acpi0 not configured
FN60 (PNP0C0B) at acpi0 not configured
FN70 (PNP0C0B) at acpi0 not configured
acpitz0 at acpi0 (THM0): active cooling level 0: 90.0C critical 98.0C
passive 52.8C
acpitz1 at acpi0 (THM2): active cooling level 0: 33.5C critical 120.0C
acpitz2 at acpi0 (THM6): active cooling level 0: 52.0C critical 60.0C
acpitz3 at acpi0 (THM7): active cooling level 0: 50.0C critical 57.0C
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x7190 (rev. 0x03)
agp0 at pchb0: aperture at 0x40000000, size 0x4000000
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x7191 (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: vendor 0x10c8 product 0x0006 (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
cbb0 at pci0 dev 2 function 0: vendor 0x104c product 0xac1b (rev. 0x03)
cbb1 at pci0 dev 2 function 1: vendor 0x104c product 0xac1b (rev. 0x03)
vendor 0x11c1 product 0x0449 (miscellaneous communications, revision
0x01) at pci0 dev 3 function 0 not configured
clcs0 at pci0 dev 6 function 0: vendor 0x1013 product 0x6003 (rev. 0x01)
clcs0: (null) (null)
clcs0: enabling CLKRUN hack
clcs0: power management port 0xef00
clcs0: interrupting at irq 11
clcs0: ac97: Crystal CS4297A codec; headphone, 20 bit DAC, 18 bit ADC,
Crystal Semi 3D
clcs0: ac97: ext id 200<AMAP>
audio0 at clcs0: full duplex, playback, capture, independent
midi1 at clcs0: CS4280 MIDI UART
pcib0 at pci0 dev 7 function 0
pcib0: vendor 0x8086 product 0x7110 (rev. 0x02)
piixide0 at pci0 dev 7 function 1
piixide0: Intel 82371AB IDE controller (PIIX4) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
uhci0 at pci0 dev 7 function 2: vendor 0x8086 product 0x7112 (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
piixpm0 at pci0 dev 7 function 3
piixpm0: vendor 0x8086 product 0x7113 (rev. 0x03)
piixpm0: can't map power management I/O space
piixpm0: interrupting at SMIpiixpm0: polling
iic0 at piixpm0: I2C bus
cbb0: cacheline 0x8 lattimer 0xa8
cbb0: bhlc 0x82a808
cbb0: interrupting at irq 11
cardslot0 at cbb0
cardbus0 at cardslot0: bus 2
pcmcia0 at cardslot0
cbb1: cacheline 0x8 lattimer 0xa8
cbb1: bhlc 0x82a808
cbb1: interrupting at irq 11
cardslot1 at cbb1
cardbus1 at cardslot1: bus 5
pcmcia1 at cardslot1
isa0 at pcib0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
acpiacad0: AC adapter online.
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
wd0 at atabus0 drive 0: <HTS726060M9AT00>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 57231 MB, 116280 cyl, 16 head, 63 sec, 512 bytes/sect x 117210240 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <TOSHIBA DVD-ROM SD-C2302, 8000106017, 1617>
cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(piixide0:1:0): using PIO mode 4, DMA mode 2 (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

 Some older Thinkpads didn't
> correctly initialise the cardbus bridge.  The result is that cardbus
> cards would use the same bus number as the internal PCI bus.  This is
> to uncomment
>
> #options       PCI_BUS_FIXUP
>
> in your kernel config and rebuild your kernel.

I'll give this a try and get back ....

/Don

>
> }-- End of excerpt from Donald Allen
>