HP Compaq nc2400 wireless (wpi)

[Eugene Prodeguene <eprod%honey.rootshell.be@localhost>]

Has anyone had any luck getting wireless (wpi) to work on the above
mentioned laptop? I was able to get the device recognized by settings the
options PCI_ADDR_FIXUP, PCI_BUS_FIXUP, PIC_INTR_FIXUP but can not get the
device into a running state. Trying to do a ifconfig wpi0 up yeilds:

wpi0: could not lock memory (repeated many times)

followed by other errors such as:

wpi0: could not read firmware file
wpi0: could not load firmware

I have installed /usr/pkgsrc/sysutils/wpi-firmware2, pushed the radio
transmitter button twice if not 10x, disabled acpi during boot, tried to
mess with bios etc all to no avail.

Ftw OpenBSD can't power up the device, FreeBSD kernel panics on boot when
trying to load modules related to if_wpi.  Linux works - so I know the
hardware is ok.  Any help/things to try would be greatly appreciated. I
also just went back to NetBSD4 to try GENERIC_LAPTOP, same issue.

dmesg:

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0 (PANOPLY) #3: Mon Jul 27 20:53:18 EDT 2009

root@[hostomitted]:/usr/src/sys/arch/i386/compile/PANOPLY
total memory = 503 MB
avail memory = 483 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Hewlett-Packard HP Compaq nc2400(#ABA) (F.06)
mainbus0 (root)
pci_addr_fixup: 000:31:1 0x8086 0x27df new address 0x00005800
pci_addr_fixup: 000:31:1 0x8086 0x27df new address 0x00005808
pci_addr_fixup: 000:31:1 0x8086 0x27df new address 0x00005810
pci_addr_fixup: 000:31:1 0x8086 0x27df new address 0x0000580c
cpu0 at mainbus0 apid 0timecounter: Timecounter "lapic" frequency 
133103347 Hz quality -100
: Intel 686-class, 1197MHz, id 0x6e8
cpu0: Enhanced SpeedStep (1036 mV) 1200 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 1200 1200 1067 933
cpu1 at mainbus0 apid 1: Intel 686-class, 1197MHz, id 0x6e8
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <HPQOEM,SLIC-MPC,00000001>, AslId <HP  ,00000001>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpiec0 at acpi0 (C005, PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
C1B2 (IFX0102) at acpi0 not configured
npx1 at acpi0 (C1C4, PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
attimer1 at acpi0 (C1C5, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pcppi1 at acpi0 (C1C7, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
hpet0 at acpi0 (C1C9, PNP0103)
hpet0: mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
pckbc1 at acpi0 (C1CD, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (C1CE, SYN0123): aux port
pckbc2: irq 12
ACEL (HPQ0004) at acpi0 not configured
hpqlb0 at acpi0 (C1D1, HPQ0006): HP Quick Launch Buttons
acpibat0 at acpi0 (C1B0, PNP0C0A-1): ACPI Battery (Control Method)
acpibat0: battery info: Hewlett-Packard, LIon, Primary 08480 2006/11/14
acpiacad0 at acpi0 (C1AF, ACPI0003): ACPI AC Adapter
acpibut0 at acpi0 (C1EB, PNP0C0E): ACPI Sleep Button
acpilid0 at acpi0 (C1E8, PNP0C0D): ACPI Lid Switch
C1F8 (PNP0C14) at acpi0 not configured
C2BF (PNP0C0B) at acpi0 not configured
C2C0 (PNP0C0B) at acpi0 not configured
C2C1 (PNP0C0B) at acpi0 not configured
C2C2 (PNP0C0B) at acpi0 not configured
acpitz0 at acpi0 (TZ0): active cooling level 0: 85.0C active cooling level 
1: 70.0C active cooling level 2: 60.0C active cooling level 3: 50.0C 
critical 105.0C passive 52.0C
acpitz1 at acpi0 (TZ1): critical 105.0C, passive cooling
acpitz2 at acpi0 (TZ2): critical 105.0C, passive cooling
acpitz3 at acpi0 (TZ3): critical 105.0C passive 31.0C, passive cooling
acpitz4 at acpi0 (TZ4): critical 110.0C, passive cooling
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x27a0 (rev. 0x03)
agp0 at pchb0: detected 7932k stolen memory
agp0: aperture at 0xe0000000, size 0x10000000
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x27a2 (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using 
wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
vendor 0x8086 product 0x27a6 (miscellaneous display, revision 0x03) at 
pci0 dev 2 function 1 not configured
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio 
Controller
azalia0: interrupting at ioapic0 pin 20
azalia0: host: 0x8086/0x27d8 (rev. 1), HDA rev. 1.0
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x01)
ppb0: disabling notification events
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
wpi0 at pci1 dev 0 function 0: vendor 0x8086 product 0x4222 (rev. 0x02)
wpi0: interrupting at ioapic0 pin 16
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: M^?M^?M^?M^?wpi0: could not lock memory
, address ff:ff:ff:ff:ff:ff
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 
24Mbps 36Mbps 48Mbps 54Mbps
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x01)
uhci0: interrupting at ioapic0 pin 21
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x01)
uhci1: interrupting at ioapic0 pin 22
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x01)
uhci2: interrupting at ioapic0 pin 22
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x01)
uhci3: interrupting at ioapic0 pin 22
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x01)
ehci0: interrupting at ioapic0 pin 21
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb1 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xe1)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
bge0 at pci2 dev 0 function 0: Broadcom BCM5788 Gigabit Ethernet
bge0: interrupting at ioapic0 pin 17
bge0: ASIC BCM5705 A3 (0x3003), Ethernet address 00:16:36:ca:cc:cd
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5705 1000BASE-T media interface, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
cbb0 at pci2 dev 9 function 0: vendor 0x104c product 0x8039 (rev. 0x00)
fwohci0 at pci2 dev 9 function 1: vendor 0x104c product 0x803a (rev. 0x00)
fwohci0: interrupting at ioapic0 pin 19
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:c0:9f:00:00:d8:9f:9d
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
vendor 0x104c product 0x803d (miscellaneous communications) at pci2 dev 9 
function 4 not configured
cbb0: cacheline 0x10 lattimer 0x40
cbb0: bhlc 0x824010
cbb0: interrupting at ioapic0 pin 18
cardslot0 at cbb0
cardbus0 at cardslot0: bus 3 cacheline 0x10, lattimer 0x40
pcmcia0 at cardslot0
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x27b9 (rev. 0x01)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801GB/GR IDE Controller (ICH7) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
isa0 at ichlpcib0
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=2, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
fwohci0: phy int
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 1197069120 Hz quality 3000
acpiacad0: AC adapter online.
azalia0: codec[0]: Analog Devices AD1981HD (rev. 2.0), HDA rev. 1.0
azalia0: codec[1]: 0x14f1/0x2bfa (rev. 0.0), HDA rev. 0.9
azalia0: codec[1]: No support for modem function groups
azalia0: codec[1] has no audio function groups
audio0 at azalia0: full duplex, independent
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <UJDA775 DVD/CDRW, , 1.21> cdrom removable
uhub0 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub1: 2 ports with 2 removable, self powered
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
wd0 at atabus0 drive 0: <TOSHIBA MK6008GAH>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 57231 MB, 116280 cyl, 16 head, 63 sec, 512 bytes/sect x 117210240 
sectors
uhub2 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 
1
uhub4: 8 ports with 8 removable, self powered
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using 
DMA)
cd0(piixide0:0:1): using PIO mode 4, DMA mode 2 (using DMA)
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 19 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 20 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 21 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
hpqlb0: registering on wskbd0
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
ubt0 at uhub2 port 1
ubt0: Broadcom Corp HP Integrated Module, rev 2.00/1.00, addr 2
ugen0 at uhub0 port 1
ugen0: vendor 0x08ff Fingerprint Sensor, rev 1.10/6.23, addr 2
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not load boot firmware
wpi0: could not load boot firmware
wpi0: could not load firmware
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: cannot assign link-local address
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not load boot firmware
wpi0: could not load boot firmware
wpi0: could not load firmware
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not load boot firmware
wpi0: could not load boot firmware
wpi0: could not load firmware
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: cannot assign link-local address
bge0: block failed to stop: reg 0x468, bit 0x00000002
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not load boot firmware
wpi0: could not load boot firmware
wpi0: could not load firmware
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory
wpi0: could not lock memory