Current-Users archive

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]

Re: Looking for Core 2 Duo mainboard suggestions



Thomas Klausner wrote:
Hi!

I'm looking for a new mainboard for a Core 2 Duo E8[246]00 CPU.

Did someone try NetBSD-current on an Asus P5Q (Deluxe) or MSI P45
(Platinum) mainboard? If so, please tell me about your experience
(supported hardware, dmesg?).

I'd also appreciate other mainboard suggestions for Core 2 Duo CPUs!

Thanks,
 Thomas


Hi Thomas,

Here is the dmesg from Asus P5Q-E (is this the Deluxe one ?) equipped with Q9300 (quad-core). Everything's fine except the msk0 card that sometimes just stops working and I have to ifconfig down up it. Although it is better with NetBSD than with Windows where using this NIC entirely freezes the system after a while. But it has a second NIC integrated that I use without problems.


--
Mihai
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.5 (Home) #3: Wed Dec 31 10:25:20 EET 2008
        
root%kefren64.netbsd.ro@localhost:/disk2/work/src/sys/arch/amd64/compile/obj/Home
total memory = 4095 MB
avail memory = 3957 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.5 @ 0xf0720 (74 entries)
System manufacturer P5Q-E (System Version)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2999MHz, id 0x10677
cpu0: Intel(R) On Demand Clock Modulation (state disabled)
cpu1 at mainbus0 apid 1: Intel 686-class, 2999MHz, id 0x10677
cpu2 at mainbus0 apid 2: Intel 686-class, 2999MHz, id 0x10677
cpu3 at mainbus0 apid 3: Intel 686-class, 2999MHz, id 0x10677
ioapic0 at mainbus0 apid 4: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <A_M_I_,OEMRSDT ,07000809>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
aiboost0 at acpi0 (ASOC, ATK0110-16843024)
aiboost0: ASUS AI Boost Hardware monitor
hpet0 at acpi0 (HPET, PNP0103)
hpet0: mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
FWH (INT0800) [Intel FWH Random Number Generator] at acpi0 not configured
UAR1 (PNP0501) [16550A-compatible COM port] at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82G45 Host Bridge (rev. 0x02)
ppb0 at pci0 dev 1 function 0: Intel product 0x2e21 (rev. 0x02)
ppb0: unsupported PCI Express version
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci1 dev 0 function 0: ATI Technologies product 0x9598 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
azalia0 at pci1 dev 0 function 1: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 17
azalia0: host: 0x1002/0xaa20 (rev. 0), HDA rev. 1.0
uhci0 at pci0 dev 26 function 0: Intel product 0x3a37 (rev. 0x00)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: Intel product 0x3a38 (rev. 0x00)
uhci1: interrupting at ioapic0 pin 21
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 26 function 2: Intel product 0x3a39 (rev. 0x00)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 26 function 7: Intel product 0x3a3c (rev. 0x00)
ehci0: interrupting at ioapic0 pin 18
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
azalia1 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia1: interrupting at ioapic0 pin 22
azalia1: host: 0x8086/0x3a3e (rev. 0), HDA rev. 1.0
ppb1 at pci0 dev 28 function 0: Intel product 0x3a40 (rev. 0x00)
pci2 at ppb1 bus 4
pci2: memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 28 function 4: Intel product 0x3a48 (rev. 0x00)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
pciide0 at pci3 dev 0 function 0
pciide0: Marvell 88SE6121 SATA II Controller (rev. 0xb1)
pciide0: bus-master DMA support present, but unused (no driver support)
pciide0: primary channel configured to native-PCI mode
pciide0: using ioapic0 pin 16 for native-PCI interrupt
atabus0 at pciide0 channel 0
pciide0: secondary channel configured to native-PCI mode
atabus1 at pciide0 channel 1
ppb3 at pci0 dev 28 function 5: Intel product 0x3a4a (rev. 0x00)
pci4 at ppb3 bus 2
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
mskc0 at pci4 dev 0 function 0mskc0: interrupt moderation is 0 us
, Yukon-2 EC Ultra rev. B0 (0x3): ioapic0 pin 17
msk0 at mskc0 port A: Ethernet address 00:22:15:80:9f:02
ukphy0 at msk0 phy 0: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000ac2, model 0x000b, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
uhci3 at pci0 dev 29 function 0: Intel product 0x3a34 (rev. 0x00)
uhci3: interrupting at ioapic0 pin 23
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 1: Intel product 0x3a35 (rev. 0x00)
uhci4: interrupting at ioapic0 pin 19
usb5 at uhci4: USB revision 1.0
uhci5 at pci0 dev 29 function 2: Intel product 0x3a36 (rev. 0x00)
uhci5: interrupting at ioapic0 pin 18
usb6 at uhci5: USB revision 1.0
ehci1 at pci0 dev 29 function 7: Intel product 0x3a3a (rev. 0x00)
ehci1: interrupting at ioapic0 pin 23
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
usb7 at ehci1: USB revision 2.0
ppb4 at pci0 dev 30 function 0: Intel 82801BA Hub-PCI Bridge (rev. 0x90)
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled
skc0 at pci5 dev 2 function 0: ioapic0 pin 18
skc0: interrupt moderation is 0 us
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk0 at skc0 port A: Ethernet address 00:22:15:80:ac:e8
makphy0 at sk0 phy 0: Marvell 88E1011 Gigabit PHY, rev. 5
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
fwohci0 at pci5 dev 3 function 0: Lucent Technologies FW322/323 IEEE 1394 Host 
Controller (rev. 0x70)
fwohci0: interrupting at ioapic0 pin 19
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 00:1e:8c:00:01:6c:ed:30
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
pcib0 at pci0 dev 31 function 0
pcib0: Intel ICH10R Watchdog Timer (rev. 0x00)
ahcisata0 at pci0 dev 31 function 2: Intel ICH10R AHCI Controller
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: AHCI revision 1.2, 6 ports, 32 command slots, features 0xef22e0e0
atabus2 at ahcisata0 channel 0
atabus3 at ahcisata0 channel 1
atabus4 at ahcisata0 channel 2
atabus5 at ahcisata0 channel 3
atabus6 at ahcisata0 channel 4
atabus7 at ahcisata0 channel 5
ichsmb0 at pci0 dev 31 function 3: Intel ICH10 SMBus Serial Bus 1 (rev. 0x00)
ichsmb0: interrupting at ioapic0 pin 18
iic0 at ichsmb0: I2C bus
spdmem0 at iic0 addr 0x50
spdmem0: DDR2 SDRAM memory, no parity or ECC, 2048MB, 800MHz (PC2-6400)
spdmem0: 14 rows, 10 cols, 2 ranks, 8 banks/chip, 2.50ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 5-5-5-18
spdmem0: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
spdmem1 at iic0 addr 0x52
spdmem1: DDR2 SDRAM memory, no parity or ECC, 2048MB, 800MHz (PC2-6400)
spdmem1: 14 rows, 10 cols, 2 ranks, 8 banks/chip, 2.50ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 5-5-5-18
spdmem1: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: ATI R600 HDMI (rev. 0.0), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
azalia1: codec[0]: 0x11d4/0x989b (rev. 3.0), HDA rev. 1.0
audio1 at azalia1: full duplex, independent
uhub0 at usb0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
uhub4 at usb6: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb4: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb5: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
uhub7 at usb7: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub7: 6 ports with 6 removable, self powered
IPsec: Initialized Security Association Processing.
ahcisata0 port 0: device present, speed: 1.5Gb/s
ahcisata0 port 1: device present, speed: 1.5Gb/s
ahcisata0 port 2: device present, speed: 3.0Gb/s
ahcisata0 port 5: device present, speed: 1.5Gb/s
umass0 at uhub3 port 1 configuration 1 interface 0
umass0: Apple Inc. iPod, rev 2.00/0.01, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <Apple, iPod, 1.62> disk removable
sd0(umass0:0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Logical Unit Is in Process Of Becoming Ready

sd0: drive offline
sd0(umass0:0:0:0):  Check Condition on CDB: 0x00 00 00 00 00 00
    SENSE KEY:  Not Ready
     ASC/ASCQ:  Logical Unit Is in Process Of Becoming Ready

uhub8 at uhub5 port 2: ALCOR Generic USB Hub, class 9/0, rev 1.10/3.12, addr 2
uhub8: 4 ports with 4 removable, self powered
sd0: fabricating a geometry
wd0 at atabus0 drive 0: <ST3120026A>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 111 GB, 232581 cyl, 16 head, 63 sec, 512 bytes/sect x 234441648 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd1 at atabus2 drive 0: <ST3160023AS>
wd1: quirks 0x2<FORCE_LBA48>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
wd2 at atabus3 drive 0: <WDC WD2000JS-55NCB1>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 186 GB, 387621 cyl, 16 head, 63 sec, 512 bytes/sect x 390721968 sectors
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd2(ahcisata0:1:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
wd3 at atabus4 drive 0: <WDC WD5000AAJS-00YFA0>
wd3: drive supports 16-sector PIO transfers, LBA48 addressing
wd3: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd3: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd3(ahcisata0:2:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
atapibus0 at atabus7: 1 targets
cd0 at atapibus0 drive 0: <LITE-ON DVDRW LH-20A1S, , 9L08> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cd0(ahcisata0:5:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) 
(using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio2 at pad0: half duplex
findroot: unable to read block 225841771
uhidev0 at uhub8 port 1 configuration 1 interface 0
uhidev0: Logitech Logitech USB Keyboard, rev 1.10/23.00, addr 3, iclass 3/1
ukbd0 at uhidev0
boot device: wd0
root on wd0a dumps on wd0b
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub8 port 1 configuration 1 interface 1
uhidev1: Logitech Logitech USB Keyboard, rev 1.10/23.00, addr 3, iclass 3/0
uhidev1: 2 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
root file system type: ffs
uhidev2 at uhub8 port 2 configuration 1 interface 0
uhidev2: Microsoft Microsoft Wireless Optical MouseM-BM-. 1.0A, rev 2.00/0.57, 
addr 4, iclass 3/1
uhidev2: 3 report ids
ums0 at uhidev2 reportid 1: 5 buttons and Z dir.
wsmouse0 at ums0 mux 0
uhid2 at uhidev2 reportid 2: input=1, output=0, feature=0
uhid3 at uhidev2 reportid 3: input=1, output=0, feature=1
uhidev3 at uhub8 port 3 configuration 1 interface 0
uhidev3: No brand 2Port KVMSwicther, rev 1.10/1.00, addr 5, iclass 3/0
ukbd1 at uhidev3
wskbd1 at ukbd1 mux 1
wskbd1: connecting to wsdisplay0
uhidev4 at uhub8 port 3 configuration 1 interface 1
uhidev4: No brand 2Port KVMSwicther, rev 1.10/1.00, addr 5, iclass 3/0
uhidev4: no input interrupt endpoint
ubt0 at uhub1 port 1skc0: interrupt moderation is 1000 us
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x25, vt100 emulation)
wsdisplay0: screen 6 added (80x25, vt100 emulation)
wsdisplay0: screen 7 added (80x25, vt100 emulation)

ubt0: vendor 0x1131 ISSCBTA, rev 1.10/3.73, addr 2
/disk2: replaying log to disk
/disk3: replaying log to disk


Home | Main Index | Thread Index | Old Index