Current-Users archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
5.0_BETA installation destroys cgd disklabel
Hi,
(dmesg from 4.0_BETA2 and 5.0_BETA attached)
I recently installed NetBSD 5.0_BETA on notebook TOSHIBA Satellite 1135.
There already were NetBSD partitions with 4.0_BETA2 installation, the
disklabel before 5.0_BETA installation was something like:
size offset fstype
a: 208845 17141355 4.2BSD 1024 8192 0
c: 208845 17141355 unused 0 0
d: 58605120 0 unused 0 0
e: 41254920 17350200 unknown
f: 17141292 63 NTFS
The root partition "a" has "init.root=/mnt" in /etc/sysctl.conf, it's
fstab is:
/dev/wd0a / ffs rw 1 1
/dev/cgd0a /mnt ffs rw 1 2
The right (working) disklabel of cgd0 is (the cgd0 lives in wd0e):
size offset fstype
a: 39157768 2097152 4.2BSD 0 0 0
b: 2097152 0 swap
d: 41254920 0 unused 0 0
Now the problem is that after installation of 5.0_BETA from cd
(downloaded from ftp, version 200812150000Z) to partition "f", the
disklabel of cgd0 looks like being "reset" or something:
size offset fstype
a: 41254920 0 4.2BSD 0 0 0
d: 41254920 0 unused 0 0
I can recover from this situation by changing the cgd "verify_method"
from "disklabel" to "none", configure the cgd0 (type the right
passphrase) and "redisklabel" the cgd0 with the right disklabel.
The wd0e config file for cgd:
algorithm aes-cbc;
iv-method encblkno;
keylength 192;
verify_method disklabel;
keygen pkcs5_pbkdf2/sha1 {
iterations ***;
salt ***=;
};
First I thought that it is impossible that the disklabel on cgd0 was
destroyed (it is even a verify method for cgd to check valid disklabel!)
and that I've done something wrong, but during the 5.0_BETA installation
I never typed the passphrase for cgd0 or worked somehow with cgd so what
could happened? After the first installation I did the mentioned
recovery and used the 4.0 and 5.0 systems without problems. Then I
wanted to split the 5.0 partition to two and did the installation again.
And again the cgd0 disklabel was destroyed. This time I was very careful
and I am sure I didn't mess up the cgd0 disklabel myself -- so I
concluded that it has to be the installation of 5.0_BETA which is
destroying the disklabel and I probably should report this problem
(should I file a PR?).
Attached are dmesg logs for both 4.0_BETA2 (built around 20070610) and
5.0_BETA (20081215).
Kind regards,
r.
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 4.0_BETA2 (GENERIC_LAPTOP_cgd_paxmprotect) #0: Sun Jun 10 00:26:29 CEST
2007
root%notysek.eq.cz@localhost:/usr/B/obj/sys/arch/i386/compile/GENERIC_LAPTOP_cgd_paxmprotect
total memory = 494 MB
rbus: rbus_min_start set to 0x40000000
avail memory = 477 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfd790
PCI BIOS rev. 2.1 found at 0xfd9a4
pcibios: config mechanism [1][x], special cycles [x][x], last bus 2
PCI IRQ Routing Table rev. 1.0 found at 0xfdf30, size 176 bytes (9 entries)
PCI Interrupt Router at 000:31:0 (Intel 82371FB (PIIX) PCI-ISA Bridge
compatible)
------------------------------------------
device vendor product pin PIRQ IRQ stage
------------------------------------------
000:02:0 0x8086 0x3582 A 0x00 11 0 already assigned
000:29:0 0x8086 0x24c2 A 0x00 11 0 already assigned
000:29:1 0x8086 0x24c4 B 0x03 10 0 already assigned
000:29:2 0x8086 0x24c7 C 0x02 11 0 already assigned
000:29:7 0x8086 0x24cd D 0x07 10 0 already assigned
000:31:1 0x8086 0x24ca A 0x02 11 0 fixed up
000:31:3 0x8086 0x24c3 B 0x01 10 0 already assigned
000:31:5 0x8086 0x24c5 B 0x01 10 0 already assigned
000:31:6 0x8086 0x24c6 B 0x01 10 0 already assigned
002:01:0 0x10ec 0x8139 A 0x03 10 0 already assigned
002:02:0 0x104c 0xac50 A 0x02 11 0 fixed up
002:04:0 0x1217 0x6933 A 0x00 11 0 fixed up
002:04:1 0x1217 0x6933 B 0x01 10 0 fixed up
------------------------------------------
mainbus0 (root)
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x00005800
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x00005808
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x00005810
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x0000580c
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x1ef00000
pci_addr_fixup: 001:02:0 0x104c 0xac50 new address 0x1ef01000
pci_addr_fixup: 001:04:0 0x1217 0x6933 new address 0x1ef02000
pci_addr_fixup: 001:04:1 0x1217 0x6933 new address 0x1ef03000
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel Mobile Pentium 4 (686-class), 2198.24 MHz, id 0xf27
cpu0: features bfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features bfebfbff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
cpu0: features bfebfbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu0: features2 4400<CID,xTPR>
cpu0: "Mobile Intel(R) Pentium(R) 4 - M CPU 2.20GHz"
cpu0: I-cache 12K uOp cache 8-way, D-cache 8 KB 64B/line 4-way
cpu0: L2 cache 512 KB 64B/line 8-way
cpu0: ITLB 4K/4M: 128 entries
cpu0: DTLB 4K/4M: 64 entries
cpu0: using thermal monitor 1
cpu0: 16 page colors
ioapic at mainbus0: not configured
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <TOSCPL,Montara ,06040000>, AslId < LTP,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
LNKA: ACPI: Found matching pin for 0.2.INTA at func 0: 11
LNKA: ACPI: Found matching pin for 0.29.INTA at func 0: 11
LNKD: ACPI: Found matching pin for 0.29.INTB at func 1: 10
LNKC: ACPI: Found matching pin for 0.29.INTC at func 2: 11
LNKH: ACPI: Found matching pin for 0.29.INTD at func 7: 10
LNKC: ACPI: Found matching pin for 0.31.INTA at func 1: 11
LNKB: ACPI: Found matching pin for 0.31.INTB at func 3: 10
LNKB: ACPI: Found matching pin for 0.31.INTB at func 3: 10
LNKB: ACPI: Found matching pin for 0.31.INTB at func 3: 10
LNKB: ACPI: Found matching pin for 1.1.INTA at func 0: 10
LNKA: ACPI: Found matching pin for 1.4.INTA at func 0: 11
LNKB: ACPI: Found matching pin for 1.4.INTB at func 1: 10
LNKC: ACPI: Found matching pin for 1.2.INTA at func 0: 11
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
CMP0101 at acpi0 not configured
PNP0A03 at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0100 at acpi0 not configured
PNP0000 at acpi0 not configured
PNP0B00 at acpi0 not configured
PNP0C04 at acpi0 not configured
PNP0200 at acpi0 not configured
PNP0C02 at acpi0 not configured
PNP0303 at acpi0 not configured
PNP0F13 at acpi0 not configured
acpiec0 at acpi0 (PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
PNP0A05 at acpi0 not configured
PNP0400 at acpi0 not configured
acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
apm0 at acpi0: Power Management spec V1.2
acpiacad0: AC adapter online.
acpibat0: battery info: TOSHIBA, Li-Ion, PA3251U , 3658Q
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82855GM Host-Hub Controller (rev. 0x01)
agp0 at pchb0: detected 16252k stolen memory
agp0: aperture at 0xe8000000, size 0x8000000
Intel 82855GM GMCH Memory Controller (miscellaneous system, revision 0x01) at
pci0 dev 0 function 1 not configured
Intel 82855GM GMCH Configuration Process (miscellaneous system, revision 0x01)
at pci0 dev 0 function 3 not configured
vga1 at pci0 dev 2 function 0: Intel 82855GM GMCH Integrated Graphics Device
(rev. 0x01)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
Intel 82855GM GMCH Integrated Graphics Device (miscellaneous display, revision
0x01) at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 29 function 0: Intel 82801DB USB UHCI Controller (rev. 0x03)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801DB USB UHCI Controller (rev. 0x03)
uhci1: interrupting at irq 10
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801DB USB UHCI Controller (rev. 0x03)
uhci2: interrupting at irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801DB USB EHCI Controller (rev. 0x03)
ehci0: interrupting at irq 10
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-PCI Bridge (rev. 0x83)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
rtk0 at pci1 dev 1 function 0: Realtek 8139 10/100BaseTX (rev. 0x10)
rtk0: interrupting at irq 10
rtk0: Ethernet address 00:02:3f:92:a2:e7
rlphy0 at rtk0 phy 7: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0 at pci1 dev 2 function 0: Texas Instruments PCI1410 PCI-CardBus Bridge
(rev. 0x01)
cbb1 at pci1 dev 4 function 0: O2 Micro OZ6933 PCI-CardBus Bridge (rev. 0x01)
cbb2 at pci1 dev 4 function 1: O2 Micro OZ6933 PCI-CardBus Bridge (rev. 0x01)
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2
pcmcia0 at cardslot0
cbb1: interrupting at irq 11
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 3
pcmcia1 at cardslot1
cbb2: interrupting at irq 10
cardslot2 at cbb2 slot 2 flags 0
cardbus2 at cardslot2: bus 4
pcmcia2 at cardslot2
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801DB ISA Bridge (rev. 0x03)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x03)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
Intel 82801DB SMBus Controller (SMBus serial bus, revision 0x03) at pci0 dev 31
function 3 not configured
auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: interrupting at irq 10
auich0: ac97: Avance Logic ALC202 codec; headphone, 20 bit DAC, 18 bit ADC,
Realtek 3D
auich0: ac97: ext id 607<AC97_22,AMAP,SPDIF,DRA,VRA>
Intel 82801DB AC97 Modem Controller (modem communications, revision 0x03) at
pci0 dev 31 function 6 not configured
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
pcppi0: children must have an explicit unit
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
auich0: measured ac97 link rate at 47994 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
Kernelized RAIDframe activated
wi0 at pcmcia0 function 0: <TOSHIBA, Wireless LAN Card, Version 01.01, >
wi0: 802.11 address 00:02:2d:b3:5f:1e
wi0: using Lucent Embedded WaveLAN/IEEE
wi0: Lucent Firmware: Station (8.10.1)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wd0 at atabus0 drive 0: <IC25N030ATCS04-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 28615 MB, 58140 cyl, 16 head, 63 sec, 512 bytes/sect x 58605120 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <DW-224E, , F.0A> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x25, vt100 emulation)
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 5.0_BETA (GENERIC) #0: Mon Dec 15 17:03:32 UTC 2008
builds%b0.netbsd.org@localhost:/home/builds/ab/netbsd-5/i386/200812150000Z-obj/home/builds/ab/netbsd-5/src/sys/arch/i386/compile/GENERIC
total memory = 494 MB
avail memory = 474 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
TOSHIBA Satellite 1135 (PS113U-3SKYMV)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2198MHz, id 0xf27
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <TOSCPL,Montara ,06040000>, AslId < LTP,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
EPWR (CMP0101) at acpi0 not configured
attimer1 at acpi0 (TIMR, PNP0100): AT Timer
attimer1: io 0x40-0x43,0x50-0x53 irq 0
npx1 at acpi0 (MATH, PNP0C04)
npx1: io 0xf0 irq 13
npx1: reported by CPUID; using exception 16
pckbc1 at acpi0 (PS2K, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F13): aux port
pckbc2: irq 12
acpiec0 at acpi0 (EC0, PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
LPBI (PNP0400) at acpi0 not configured
acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (BAT1, PNP0C0A-1): ACPI Battery (Control Method)
acpibat0: battery info: TOSHIBA, Li-Ion, PA3251U 3658Q
apm0 at acpi0: Power Management spec V1.2
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x3580 (rev. 0x01)
agp0 at pchb0: detected 16252k stolen memory
agp0: aperture at 0xe8000000, size 0x8000000
vendor 0x8086 product 0x3584 (miscellaneous system, revision 0x01) at pci0 dev
0 function 1 not configured
vendor 0x8086 product 0x3585 (miscellaneous system, revision 0x01) at pci0 dev
0 function 3 not configured
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x3582 (rev. 0x01)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
vendor 0x8086 product 0x3582 (miscellaneous display, revision 0x01) at pci0 dev
2 function 1 not configured
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x24c2 (rev. 0x03)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x24c4 (rev. 0x03)
uhci1: interrupting at ioapic0 pin 19
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x24c7 (rev. 0x03)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x24cd (rev. 0x03)
ehci0: interrupting at ioapic0 pin 23
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
ppb0 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0x83)
pci1 at ppb0 bus 2
pci1: i/o space, memory space enabled
rtk0 at pci1 dev 1 function 0: Realtek 8139 10/100BaseTX (rev. 0x10)
rtk0: interrupting at ioapic0 pin 17
rtk0: Ethernet address 00:02:3f:92:a2:e7
rlphy0 at rtk0 phy 7: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0 at pci1 dev 2 function 0: vendor 0x104c product 0xac50 (rev. 0x01)
cbb1 at pci1 dev 4 function 0: vendor 0x1217 product 0x6933 (rev. 0x01)
cbb2 at pci1 dev 4 function 1: vendor 0x1217 product 0x6933 (rev. 0x01)
cbb0: cacheline 0x0 lattimer 0x10
cbb0: bhlc 0x21000
cbb0: secondary bus number uninitialized; try PCI_BUS_FIXUP
cbb0: interrupting at ioapic0 pin 18
cardslot0 at cbb0
pcmcia0 at cardslot0
cbb1: cacheline 0x0 lattimer 0x40
cbb1: bhlc 0x824000
cbb1: secondary bus number uninitialized; try PCI_BUS_FIXUP
cbb1: interrupting at ioapic0 pin 16
cardslot1 at cbb1
pcmcia1 at cardslot1
cbb2: cacheline 0x0 lattimer 0x40
cbb2: bhlc 0x824000
cbb2: secondary bus number uninitialized; try PCI_BUS_FIXUP
cbb2: interrupting at ioapic0 pin 17
cardslot2 at cbb2
pcmcia2 at cardslot2
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x24cc (rev. 0x03)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
ichlpcib0: SpeedStep enabled
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x03)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x24c3 (rev. 0x03)
ichsmb0: interrupting at ioapic0 pin 17
iic0 at ichsmb0: I2C bus
auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: interrupting at ioapic0 pin 17
auich0: ac97: Avance Logic ALC202 codec; headphone, 20 bit DAC, 18 bit ADC,
Realtek 3D
auich0: ac97: ext id 607<AC97_22,AMAP,SPDIF,DRA,VRA>
vendor 0x8086 product 0x24c6 (modem communications, revision 0x03) at pci0 dev
31 function 6 not configured
isa0 at ichlpcib0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
attimer1: attached to pcppi0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
acpiacad0: AC adapter online.
auich0: measured ac97 link rate at 47993 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
wi0 at pcmcia0 function 0: <TOSHIBA, Wireless LAN Card, Version 01.01, >
wi0: 802.11 address 00:02:2d:b3:5f:1e
wi0: using Lucent Embedded WaveLAN/IEEE
wi0: Lucent Firmware: Station (8.10.1)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wd0 at atabus0 drive 0: <IC25N030ATCS04-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 28615 MB, 58140 cyl, 16 head, 63 sec, 512 bytes/sect x 58605120 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <DW-224E, , F.0A> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0f dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x50, vt100 emulation)
wsdisplay0: screen 2 added (80x50, vt100 emulation)
wsdisplay0: screen 3 added (80x50, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
Home |
Main Index |
Thread Index |
Old Index