Re: Current on a Dell OptiPlex 760

[Mark Davies <mark%mcs.vuw.ac.nz@localhost>]

On Thu, 27 Nov 2008, Robert Elz wrote:
> Jared's acpi patch doesn't work for me either.

> On the assuption that it is some piece of hardware that is blocking
> the shutdown, I am appending a dmesg from this system (running a
> rather otder kernel than current) - perhaps you can find sme things
> in common with your Dell wich may perhaps narrow the search.  
> About the only thing I know isn't relevant is he USB mouse, as it
> fails to power down when that isn't there, as well as when it is.


For completeness I'll attach a dmesg for the 760 below but one 
(possibly) interesting thing I found while poking at this: if I boot 
the machine with "boot netbsd -v -x" then a "halt -p" does actually 
power it off.

cheers
mark

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 
2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.3 (GENERIC) #0: Thu Nov 20 16:06:26 PST 2008
        
builds@wb28:/home/builds/ab/HEAD/i386/200811200002Z-obj/home/builds/ab/HEAD/src/sys/arch/i386/compile/GENERIC
total memory = 3291 MB
avail memory = 3223 MB
timecounter: Timecounters tick every 10.000 msec
RTC BIOS diagnostic error 11<memory_size>
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Dell Inc. OptiPlex 760                 
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2992MHz, id 0x1067a
cpu0: Enhanced SpeedStep (1244 mV) 900 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 900 800 700 600
cpu1 at mainbus0 apid 1: Intel 686-class, 2992MHz, id 0x1067a
ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <DELL  , B10K   ,00000015>, AslId <ASL ,00000061>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpibut0 at acpi0 (VBTN, PNP0C0C): ACPI Power Button
npx1 at acpi0 (FPU, PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
pcppi1 at acpi0 (SPK, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x5f irq 0
PRT (PNP0401) at acpi0 not configured
COMA (PNP0501) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103)
hpet0: mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x2e10 (rev. 0x03)
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x2e12 (rev. 
0x03)
vga1: WARNING: ignoring 64-bit BAR @ 0x10
vga1: WARNING: ignoring 64-bit BAR @ 0x18
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
vendor 0x8086 product 0x2e13 (miscellaneous display, revision 0x03) at 
pci0 dev 2 function 1 not configured
vendor 0x8086 product 0x2e14 (miscellaneous communications, revision 
0x03) at pci0 dev 3 function 0 not configured
pciide0 at pci0 dev 3 function 2
pciide0: vendor 0x8086 product 0x2e16 (rev. 0x03)
pciide0: bus-master DMA support present, but unused (no driver 
support)
pciide0: primary channel wired to native-PCI mode
pciide0: using ioapic0 pin 18 for native-PCI interrupt
atabus0 at pciide0 channel 0
pciide0: secondary channel wired to native-PCI mode
atabus1 at pciide0 channel 1
vendor 0x8086 product 0x2e17 (serial communications, interface 0x02, 
revision 0x03) at pci0 dev 3 function 3 not configured
vendor 0x8086 product 0x10de (ethernet network, revision 0x02) at pci0 
dev 25 function 0 not configured
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x3a67 (rev. 
0x02)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x3a68 (rev. 
0x02)
uhci1: interrupting at ioapic0 pin 17
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 26 function 2: vendor 0x8086 product 0x3a69 (rev. 
0x02)
uhci2: interrupting at ioapic0 pin 22
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x3a6c (rev. 
0x02)
ehci0: interrupting at ioapic0 pin 22
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio 
Controller
azalia0: interrupting at ioapic0 pin 16
azalia0: host: 0x8086/0x3a6e (rev. 2), HDA rev. 1.0
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x3a70 (rev. 
0x02)
ppb0: unsupported PCI Express version
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x3a72 (rev. 
0x02)
ppb1: unsupported PCI Express version
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
uhci3 at pci0 dev 29 function 0: vendor 0x8086 product 0x3a64 (rev. 
0x02)
uhci3: interrupting at ioapic0 pin 23
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 1: vendor 0x8086 product 0x3a65 (rev. 
0x02)
uhci4: interrupting at ioapic0 pin 17
usb5 at uhci4: USB revision 1.0
uhci5 at pci0 dev 29 function 2: vendor 0x8086 product 0x3a66 (rev. 
0x02)
uhci5: interrupting at ioapic0 pin 18
usb6 at uhci5: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x3a6a (rev. 
0x02)
ehci1: interrupting at ioapic0 pin 23
ehci1: BIOS refuses to give up ownership, using force
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
usb7 at ehci1: USB revision 2.0
ppb2 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 
0xa2)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled
rtk0 at pci3 dev 0 function 0: Realtek 8139 10/100BaseTX (rev. 0x10)
rtk0: interrupting at ioapic0 pin 16
rtk0: Ethernet address 00:0e:2e:ad:1f:e9
rlphy0 at rtk0 phy 7: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 31 function 0
pcib0: vendor 0x8086 product 0x3a1a (rev. 0x02)
piixide0 at pci0 dev 31 function 2
piixide0: Intel ICH10 Serial ATA 2 Controller 4x1 (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to native-PCI mode
piixide0: using ioapic0 pin 18 for native-PCI interrupt
atabus2 at piixide0 channel 0
piixide0: secondary channel configured to native-PCI mode
atabus3 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x3a60 (rev. 
0x02)
ichsmb0: interrupting at ioapic0 pin 18
iic0 at ichsmb0: I2C bus
piixide1 at pci0 dev 31 function 5
piixide1: Intel ICH10 Serial ATA 2 Controller 2x1 (rev. 0x02)
piixide1: bus-master DMA support present
piixide1: primary channel wired to native-PCI mode
piixide1: using ioapic0 pin 18 for native-PCI interrupt
atabus4 at piixide1 channel 0
piixide1: secondary channel wired to native-PCI mode
atabus5 at piixide1 channel 1
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[2]: 0x11d4/0x194a (rev. 4.0), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, 
addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, 
addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, 
addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, 
addr 1
uhub3: 6 ports with 6 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, 
addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, 
addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, 
addr 1
uhub6: 2 ports with 2 removable, self powered
uhub7 at usb7: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, 
addr 1
uhub7: 6 ports with 6 removable, self powered
uhub8 at uhub0 port 1: Dell Dell USB Keyboard Hub, class 9/0, rev 
1.10/2.00, addr 2
uhub8: 3 ports with 2 removable, bus powered
wd0 at atabus2 drive 0: <ST3250310AS>
wd0: quirks 2<FORCE_LBA48>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 232 GB, 484406 cyl, 16 head, 63 sec, 512 bytes/sect x 488281250 
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 
(Ultra/133)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) 
(using DMA)
uhidev0 at uhub8 port 1 configuration 1 interface 0
uhidev0: Dell Dell USB Keyboard Hub, rev 1.10/2.00, addr 3, iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub8 port 1 configuration 1 interface 1
uhidev1: Dell Dell USB Keyboard Hub, rev 1.10/2.00, addr 3, iclass 3/0
uhidev1: 3 report ids
uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid2 at uhidev1 reportid 3: input=3, output=1, feature=1
uhidev2 at uhub0 port 2 configuration 1 interface 0
uhidev2: vendor 0x413c product 0x3010, rev 2.00/2.20, addr 4, iclass 
3/1
ums0 at uhidev2: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
atapibus0 at atabus3: 2 targets
cd0 at atapibus0 drive 0: <TSSTcorp DVD+/-RW TS-L633A, , D300> cdrom 
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 
(Ultra/100)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) 
(using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)