Hi all,
since 5.0_BETA I have a problem with tar. When I try to untar some
packages, system hangs and display similar message:
dmode 35b0 mode 35b0 dgen 0 gen 0
size 0 blocks 0
ino 59456 ipref 55200
panic: ffs_valloc: dup alloc
fatal breakpoint trap in supervisor mode
trap type 1 code 0 eip c053393c cs 8 eflags 246 cr2 cc374000 ilevel 0
Stopped in pid 23022.1 (tar) at netbsd:breakpoint+0x4: popl %ebp
db{0}>
I got above message when I've trying to build db4 from pkgsrc.
Here is dmesg:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 5.0_BETA (GENERIC) #1: Fri Oct 31 22:27:38 CET 2008
ktulu@dell_desktop:/usr/dest/obj/sys/arch/i386/compile/GENERIC
total memory = 1015 MB
avail memory = 986 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Dell Computer Corporation OptiPlex GX260
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 1992MHz, id 0xf27
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <DELL , GX260 ,00000006>, AslId <ASL ,00000061>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpibut0 at acpi0 (VBTN, PNP0C0C): ACPI Power Button
npx1 at acpi0 (FPU, PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
pcppi1 at acpi0 (SPK, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x5f irq 0
FDC (PNP0700) at acpi0 not configured
pckbc1 at acpi0 (KBD, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
COMA (PNP0501) at acpi0 not configured
COMB (PNP0501) at acpi0 not configured
PRT (PNP0401) at acpi0 not configured
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: unable to establish interrupt for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x2560 (rev. 0x01)
agp0 at pchb0: detected 8060k stolen memory
agp0: aperture at 0xe8000000, size 0x8000000
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x2562 (rev. 0x01)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x24c2 (rev. 0x01)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x24c4 (rev. 0x01)
uhci1: interrupting at ioapic0 pin 19
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x24c7 (rev. 0x01)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x24cd (rev. 0x01)
ehci0: interrupting at ioapic0 pin 23
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
ppb0 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0x81)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
wm0 at pci1 dev 12 function 0: Intel i82540EM 1000BASE-T Ethernet, rev. 2
wm0: interrupting at ioapic0 pin 18
wm0: 32-bit 33MHz PCI bus
wm0: 256 word (8 address bits) MicroWire EEPROM
wm0: Ethernet address 00:08:74:ed:5c:91
makphy0 at wm0 phy 1: Marvell 88E1011 Gigabit PHY, rev. 3
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x24c0 (rev. 0x01)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801DB IDE Controller (ICH4) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x24c3 (rev. 0x01)
ichsmb0: interrupting at ioapic0 pin 17
iic0 at ichsmb0: I2C bus
auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: interrupting at ioapic0 pin 17
auich0: ac97: Analog Devices AD1981B codec; headphone, 20 bit DAC, no 3D stereo
auich0: ac97: ext id 601<AC97_22,AMAP,VRA>
isa0 at ichlpcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
auich0: measured ac97 link rate at 47999 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
uhidev0 at uhub0 port 1 configuration 1 interface 0
uhidev0: Logitech Optical USB Mouse, rev 2.00/3.40, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse1 at ums0 mux 0
wd0 at atabus0 drive 0: <WDC WD400BB-75DEA0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 38146 MB, 77504 cyl, 16 head, 63 sec, 512 bytes/sect x 78125000 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <TEAC CD-ROM CD-224E, , D.9D> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x25, vt100 emulation)
pckbport: command timeout
pms_enable: command error 35
pckbport: command timeout
pckbport: command timeout
pms_disable: command error
pckbport: command timeout
pms_enable: command error 35
Firstly, I thought that problems rely on WAPBL, I disabled it and it
still occurs.
Regards,
Łukasz
Attachment:
signature.asc
Description: PGP signature