azalia mixer issues on a vaio pcg-6n2l

[cris%sleepy.giant.net@localhost]

Hey, 

I've a Vaio PCQ-6N2L and am running 4.99.72, from the August 22nd snapshot 
on an x86_64 platform.  I wasn't sure if I should toss this over to that 
group, or here, though half the posts on this audio device seem to be in 
the i386 group.

Basically, from what I can tell mixerctl needs a slight nudge to attach 
correctly to it, and I can't find the documentation to do so.  I was 
wondering if anyone else had any better luck with something simmilar or 
had any clue what I could set to get any sound out of it.



NetBSD 4.99.72 (GENERIC) #0: Fri Aug 22 07:32:40 PDT 2008
        
builds@wb28:/home/builds/ab/HEAD/amd64/200808220002Z-obj/home/builds/ab/
HEAD/src/sys/arch/amd64/compile/GENERIC
total memory = 1022 MB
avail memory = 975 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.31 @ 0xdc010 (19 entries)
Sony Corporation VGN-SZ340P (R5206107)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2333MHz, id 0x6f6
cpu0: Enhanced SpeedStep (1308 mV) 2333 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 2333 2167 2000 1833 
1667 1
500 1333 1167 1000
cpu1 at mainbus0 apid 1: Intel 686-class, 2333MHz, id 0x6f6
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <  Sony,      N0,20060710>, AslId <PTL ,00000000>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpilid0 at acpi0 (LID0, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
acpiec0 at acpi0 (EC0, PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
acpibat0 at acpi0 (BAT1, PNP0C0A-1): ACPI Battery (Control Method)
acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
FWHD (INT0800) at acpi0 not configured
attimer1 at acpi0 (TIMR, PNP0100): AT Timer
attimer1: io 0x40-0x43,0x50-0x53 irq 0
TPM (IFX0102) at acpi0 not configured
sony0 at acpi0 (SNC, SNY5001): Sony Miscellaneous Controller
pckbc1 at acpi0 (PS2K, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, SNY9001): aux port
pckbc2: irq 12
acpitz0 at acpi0 (ATF0): critical 99.9C passive 66.9C, passive cooling
acpitz1 at acpi0 (DTS0): critical 100.8C passive 67.9C, passive cooling
acpitz2 at acpi0 (DTS1): critical 100.8C passive 66.9C, passive cooling
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x27a0 (rev. 0x03)
agp0 at pchb0: can't find internal VGA device config space
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x27a1 (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci1 dev 0 function 0: vendor 0x10de product 0x01d8 (rev. 0xa1)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using 
wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio 
Controller
azalia0: interrupting at ioapic0 pin 21
azalia0: host: 0x8086/0x27d8 (rev. 2), HDA rev. 1.0
ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x02)
ppb1: disabling notification events
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 28 function 1: vendor 0x8086 product 0x27d2 (rev. 0x02)
pci3 at ppb2 bus 6
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
wpi0 at pci3 dev 0 function 0: vendor 0x8086 product 0x4222 (rev. 0x02)
wpi0: interrupting at ioapic0 pin 17
wpi0: MoW1, address 00:18:de:3e:de:fc
wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 
24Mbps 36M
bps 48Mbps 54Mbps
ppb3 at pci0 dev 28 function 2: vendor 0x8086 product 0x27d4 (rev. 0x02)
pci4 at ppb3 bus 7
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
mskc0 at pci4 dev 0 function 0mskc0: interrupt moderation is 0 us
, Yukon-2 FE rev. A1 (0x1): ioapic0 pin 18
msk0 at mskc0 port A: Ethernet address 00:13:a9:8a:29:d7
ukphy0 at msk0 phy 0: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000ac2, model 0x0008, rev. 3
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ukphy1 at msk0 phy 3: Generic IEEE 802.3u media interface
ukphy1: OUI 0x400840, model 0x0004, rev. 0
ukphy1: no media present
ukphy2 at msk0 phy 6: Generic IEEE 802.3u media interface
ukphy2: OUI 0x002200, model 0x0011, rev. 0
ukphy2: no media present
ppb4 at pci0 dev 28 function 3: vendor 0x8086 product 0x27d6 (rev. 0x02)
pci5 at ppb4 bus 8
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 19
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x02)
uhci2: interrupting at ioapic0 pin 19
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x02)
uhci3: interrupting at ioapic0 pin 19
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x02)
ehci0: interrupting at ioapic0 pin 23
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xe2)
pci6 at ppb5 bus 9
pci6: i/o space, memory space enabled
cbb0 at pci6 dev 4 function 0: vendor 0x104c product 0x8039 (rev. 0x00)
fwohci0 at pci6 dev 4 function 1: vendor 0x104c product 0x803a (rev. 0x00)
fwohci0: interrupting at ioapic0 pin 21
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 08:00:46:03:02:28:27:32
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
vendor 0x104c product 0x803b (miscellaneous mass storage) at pci6 dev 4 
function
 2 not configured
cbb0: cacheline 0x10 lattimer 0x40
cbb0: bhlc 0x824010
cbb0: interrupting at ioapic0 pin 20
cardslot0 at cbb0
cardbus0 at cardslot0: bus 10
pcmcia0 at cardslot0
pcib0 at pci0 dev 31 function 0
pcib0: vendor 0x8086 product 0x27b9 (rev. 0x02)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801GB/GR IDE Controller (ICH7) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
piixide1 at pci0 dev 31 function 2
piixide1: Intel 82801GBM/GHM Serial ATA Controller (ICH7) (rev. 0x02)
piixide1: bus-master DMA support present
piixide1: primary channel configured to native-PCI mode
piixide1: using ioapic0 pin 22 for native-PCI interrupt
atabus1 at piixide1 channel 0
piixide1: secondary channel configured to native-PCI mode
atabus2 at piixide1 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 
0x02)
ichsmb0: polling
iic0 at ichsmb0: I2C bus
isa0 at pcib0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
attimer1: attached to pcppi0
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc1, gen=1, CYCLEMASTER mode
ieee1394if0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
ieee1394if0: bus manager 1 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 2333655940 Hz quality 3000
azalia0: codec[0]: 0x8384/0x7661 (rev. 66.1), HDA rev. 1.0
azalia0: codec[1]: 0x14f1/0x2bfa (rev. 0.0), HDA rev. 0.9
azalia0: codec[1]: No support for modem function groups
azalia0: codec[1] has no audio function groups
audio0 at azalia0: full duplex, independent
acpiacad0: AC adapter online.
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <MATSHITAUJ-842D, , 1.00> cdrom removable
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 
1
uhub4: 8 ports with 8 removable, self powered
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using 
DMA)
ieee1394if0: New S400 device ID:00063a280008232b
sbp0 at ieee1394if0: SBP-2/SCSI over IEEE1394
scsibus0 at sbp0: 1 target, 0 luns per target
sd0 at scsibus0 target 0 lun 0: <DMI, MAXTOR 6L080J4, 0473> disk fixed
sd0: fabricating a geometry
sd0: 76345 MB, 76345 cyl, 64 head, 32 sec, 512 bytes/sect x 156355584 
sectors
sd0: fabricating a geometry
ugen0 at uhub4 port 6
ugen0: vendor 0x05ca product 0x1830, rev 2.00/1.00, addr 2
ugen1 at uhub2 port 1
ugen1: STMicroelectronics Biometric Coprocessor, rev 1.00/0.01, addr 2
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
ubt0 at uhub3 port 2
ubt0: ALPS UGX, rev 2.00/19.15, addr 2
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)


# mixerctl -av
inputs.dac02.mute=off  [ off on ]
inputs.dac02=126,126  delta=2
inputs.dac02.lrswap=off  [ off on ]
inputs.dac03.mute=off  [ off on ]
inputs.dac03=126,126  delta=2
inputs.dac03.lrswap=off  [ off on ]
inputs.dac04.mute=off  [ off on ]
inputs.dac04=126,126  delta=2
inputs.dac04.lrswap=off  [ off on ]
inputs.dac05.mute=off  [ off on ]
inputs.dac05=126,126  delta=2
inputs.dac05.lrswap=off  [ off on ]
inputs.sel07.lrswap=off  [ off on ]
inputs.sel09.sel15.mut=off  [ off on ]
inputs.sel09.sel15=119,119  delta=17
inputs.sel09.lrswap=off  [ off on ]
outputs.black0a.dir=output  [ input output ]
outputs.black0a.boost=off  [ off on ]
outputs.red0d.dir=output  [ input output ]
outputs.red0d.boost=off  [ off on ]
inputs.sel15.source=black0a  [ black0a red0d black14 dac02 ]
outputs.sel15.mute=off  [ off on ]
outputs.sel15=126,126  delta=63
inputs.beep16=85  delta=85
outputs.volume17=126  delta=2
playback.mode=05  [ 05 02 03 04 10 18 ]
record.mode=06  [ 06 08 12 ]