NetBSD vs. Acer Aspire One (feat. dmesg)

[Tobias Nygren <tnn%NetBSD.org@localhost>]

Hi,

Here's the dmesg from an Acer Aspire One netbook. Most of the
hardware seems to work. Some caveats:

ath(4): Needs the "EEE patch" [1] or it won't attach. After applying it
works fine.

re(4): Seems to transmit and receive frames, but doesn't work very
well, and doesn't read out it's Ethernet address properly. Probably easy
to fix?

drm(4): Assuming this works since it's an intel chipset, but haven't
tried it yet. We'll see after X.org is up and running.

[1] http://ftp.netbsd.org/pub/NetBSD/misc/jmcneill/atheee.patch

Cheers,
-Tobias

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.72 (GENERIC.a1) #0: Thu Aug 21 00:49:52 CEST 2008
        
tnn%x40.int.nygren.pp.se@localhost:/usb/obj/sys/arch/i386/compile/GENERIC.a1
total memory = 1011 MB
avail memory = 982 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Acer AOA150 (1)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 1596MHz, id 0x106c2
cpu1 at mainbus0 apid 1: Intel 686-class, 1596MHz, id 0x106c2
ioapic0 at mainbus0 apid 4: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <INTEL ,Napa    ,00000001>, AslId <    ,01000013>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
acpilid0 at acpi0 (LID0, PNP0C0D): ACPI Lid Switch
acpibut1 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
acpibat0 at acpi0 (BAT1, PNP0C0A-0): ACPI Battery (Control Method)
acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
hpet0 at acpi0 (HPET, PNP0103)
hpet0: mem 0xfed00000-0xfed003ff irq 0,8
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
npx1 at acpi0 (FPU, PNP0C04)
npx1: io 0xf0 irq 13
npx1: reported by CPUID; using exception 16
attimer1 at acpi0 (TIMR, PNP0100): AT Timer
attimer1: io 0x40-0x43,0x50-0x53
FWHD (INT0800) at acpi0 not configured
pckbc1 at acpi0 (KBC, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (MOUE, PNP0F13): aux port
pckbc2: irq 12
acpiec0 at acpi0 (EC0, PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
WMID (PNP0C14) at acpi0 not configured
apm0 at acpi0: Power Management spec V1.2
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pms0: Synaptics touchpad version 7.2
pms0: Palm detect
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x27ac (rev. 0x03)
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x27ae (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
vendor 0x8086 product 0x27a6 (miscellaneous display, revision 0x03) at pci0 dev 
2 function 1 not configured
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 16
azalia0: host: 0x8086/0x27d8 (rev. 2), HDA rev. 1.0
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x02)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x27d2 (rev. 0x02)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
re0 at pci2 dev 0 function 0: RealTek 8100E/8101E PCIe 10/100BaseTX (rev. 0x02)
re0: interrupting at ioapic0 pin 17
re0: Unknown revision (0x24800000)
re0: Ethernet address 00:00:00:00:00:00
re0: using 256 tx descriptors
rlphy0 at re0 phy 7: RTL8201L 10/100 media interface, rev. 1
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ppb2 at pci0 dev 28 function 2: vendor 0x8086 product 0x27d4 (rev. 0x02)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled
ath0 at pci3 dev 0 function 0
ath0: interrupting at ioapic0 pin 18
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 
36Mbps 48Mbps 54Mbps
ath0: mac 14.2 phy 7.0 radio 10.2
ppb3 at pci0 dev 28 function 3: vendor 0x8086 product 0x27d6 (rev. 0x02)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 17
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x02)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x02)
uhci3: interrupting at ioapic0 pin 19
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x02)
ehci0: interrupting at ioapic0 pin 16
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb4 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xe2)
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled
pcib0 at pci0 dev 31 function 0
pcib0: vendor 0x8086 product 0x27b9 (rev. 0x02)
piixide0 at pci0 dev 31 function 2
piixide0: Intel 82801GBM/GHM Serial ATA Controller (ICH7) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 0x02)
ichsmb0: interrupting at ioapic0 pin 17
iic0 at ichsmb0: I2C bus
spdmem0 at iic0 addr 0x51
spdmem0: DDR2 SDRAM memory, no parity or ECC, 512MB, 667MHz, PC2-5300
spdmem0: 13 rows, 10 cols, 2 ranks, 4 banks/chip, 3.00ns cycle time
spdmem0: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
isa0 at pcib0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
attimer1: attached to pcppi0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: Realtek ALC268 (rev. 1.1), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
acpiacad0: AC adapter offline.
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
acpibat0: battery info: SIMPLO, LION, UM08A73 038C
acpibat0: battery info: SIMPLO, LION, UM08A73 038C
ugen0 at uhub4 port 5
ugen0: Sonix Technology Co., Ltd. USB 2.0 Camera, rev 2.00/1.00, addr 2
wd0 at atabus0 drive 0: <ST9120817AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 111 GB, 232581 cyl, 16 head, 63 sec, 512 bytes/sect x 234441648 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
/: replaying log to memory
root file system type: ffs
/: replaying log to disk
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)


# /usr/sbin/cpuctl identify 0
cpu0: Intel Pentium Pro, II or III (686-class), 1596.13 MHz, id 0x106c2
cpu0: features bfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features bfe9fbff<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features bfe9fbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu0: features2 40c39d<SSE3,DTES64,MONITOR,DS-CPL,EST,TM2,SSSE3,xTPR,PDCM>
cpu0: "Intel(R) Atom(TM) CPU N270   @ 1.60GHz"
cpu0: I-cache 32KB 64B/line 8-way
cpu0: Initial APIC ID 0
cpu0: Cluster/Package ID 0
cpu0: SMT ID 0
cpu0: family 06 model 0c extfamily 00 extmodel 01