I can't get into firmware on this right now as the serial port it's
on for console is a crappy USB that doesn't seem to pass along a BREAK
:-(.
Here's the dmesg. I'm wondering if the disks I can't
see were totally wiped of VTOC before I bought them and the ones I can
see weren't.
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 7.0.1 (GENERIC.201605221355Z)
total memory = 8192 MB
avail memory = 8026 MB
kern.module.path=/stand/
sparc64/7.0/modules
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root): SUNW,Sun-Fire-V245 (Sun Fire V245): hostid 84acb70a
cpu0 at mainbus0: SUNW,UltraSPARC-IIIi @ 1504 MHz, CPU id 0
cpu0: manuf 3e, impl 16, mask 34
cpu0: system tick frequency 20 MHz
cpu0: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
cpu1 at mainbus0: SUNW,UltraSPARC-IIIi @ 1504 MHz, CPU id 1
cpu1: manuf 3e, impl 16, mask 34
cpu1: system tick frequency 20 MHz
cpu1: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
memory-controller at mainbus0 not configured
memory-controller at mainbus0 not configured
pyro0 at mainbus0: "Fire", rev 3, ign 780, bus A 2 to 13
pyro0: pci0 at pyro0
pci0: i/o space, memory space enabled
ppb0 at pci0 dev 0 function 0: PLX Technology product 0x8532 (rev. 0xbb)
ppb0: PCI Express capability version 1 <Upstream Port of PCI-E Switch>
pci1 at ppb0 bus 3
pci1: i/o space, memory space enabled
ppb1 at pci1 dev 1 function 0: PLX Technology product 0x8532 (rev. 0xbb)
ppb1: PCI Express capability version 1 <Downstream Port of PCI-E Switch> x4 @ 2.5GT/s
pci2 at ppb1 bus 4
pci2: i/o space, memory space enabled
ppb2 at pci2 dev 0 function 0: Acer Labs M5249 Hypertransport to PCI Bridge (rev. 0x00)
ppb2: PCI Express capability version 1 <PCI-E to PCI/PCI-X Bridge>
pci3 at ppb2 bus 5
pci3: i/o space, memory space enabled
ohci0 at pci3 dev 28 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 0x03)
ohci0: interrupting at ivec 780
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci3 dev 28 function 1: Acer Labs M5237 USB 1.1 Host Controller (rev. 0x03)
ohci1: interrupting at ivec 780
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ehci0 at pci3 dev 28 function 3: Acer Labs M5239 USB 2.0 Host Controller (rev. 0x01)
ehci0: interrupting at ivec 781
ehci0: EHCI version 1.0
ehci0: wrong number of companions (3 != 2)
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
ebus0 at pci3 dev 30 function 0
ebus0: Acer Labs product 0x1575, revision 0x00
rtc0 at ebus0 addr 70-73: mc146818 compatible time-of-day clock: m5823
aceride0 at pci3 dev 31 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 0xc8)
aceride0: bus-master DMA support present
aceride0: primary channel configured to native-PCI mode
aceride0: using ivec 1f84 for native-PCI interrupt
atabus0 at aceride0 channel 0
aceride0: secondary channel configured to native-PCI mode
atabus1 at aceride0 channel 1
ppb3 at pci1 dev 2 function 0: PLX Technology product 0x8532 (rev. 0xbb)
ppb3: PCI Express capability version 1 <Downstream Port of PCI-E Switch> x4 @ 2.5GT/s
pci4 at ppb3 bus 6
pci4: i/o space, memory space enabled
ppb4 at pci1 dev 8 function 0: PLX Technology product 0x8532 (rev. 0xbb)
ppb4: PCI Express capability version 1 <Downstream Port of PCI-E Switch> x8 @ 2.5GT/s
pci5 at ppb4 bus 7
pci5: i/o space, memory space enabled
ppb5 at pci1 dev 9 function 0: PLX Technology product 0x8532 (rev. 0xbb)
ppb5: PCI Express capability version 1 <Downstream Port of PCI-E Switch> x4 @ 2.5GT/s
pci6 at ppb5 bus 8
pci6: i/o space, memory space enabled
ppb6 at pci6 dev 0 function 0: ServerWorks BCM5714/BCM5715 Integral PCI-E to PCI-X Bridge (rev. 0xb5)
ppb6: PCI Express capability version 1 <PCI-E to PCI/PCI-X Bridge>
pci7 at ppb6 bus 9
pci7: i/o space, memory space enabled
bge0 at pci7 dev 4 function 0: Broadcom BCM5714 Gigabit Ethernet
bge0: interrupting at ivec 3795
bge0: HW config 00010115, 00000015, 00000000, 00000000 00000000
bge0: ASIC BCM5715 A3 (0x9003), Ethernet address 00:14:4f:ac:b7:0a
bge0: WARNING: failed to restrict dma range, falling back to parent bus dma range
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5714 1000BASE-T/X media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1 at pci7 dev 4 function 1: Broadcom BCM5714 Gigabit Ethernet
bge1: interrupting at ivec 3796
bge1: HW config 00000114, 00000014, 00000000, 00000000 00000000
bge1: ASIC BCM5715 A3 (0x9003), Ethernet address 00:14:4f:ac:b7:0a
bge1: WARNING: failed to restrict dma range, falling back to parent bus dma range
bge1: setting short Tx thresholds
brgphy1 at bge1 phy 1: BCM5714 1000BASE-T/X media interface, rev. 0
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb7 at pci7 dev 8 function 0: ServerWorks HT1000 PCI/PCI-X Bridge (rev. 0xb4)
pci8 at ppb7 bus 10
pci8: i/o space, memory space enabled
ppb8 at pci1 dev 10 function 0: PLX Technology product 0x8532 (rev. 0xbb)
ppb8: PCI Express capability version 1 <Downstream Port of PCI-E Switch> x4 @ 2.5GT/s
pci9 at ppb8 bus 11
pci9: i/o space, memory space enabled
ppb9 at pci9 dev 0 function 0: ServerWorks BCM5714/BCM5715 Integral PCI-E to PCI-X Bridge (rev. 0xb5)
ppb9: PCI Express capability version 1 <PCI-E to PCI/PCI-X Bridge>
pci10 at ppb9 bus 12
pci10: i/o space, memory space enabled
bge2 at pci10 dev 4 function 0: Broadcom BCM5714 Gigabit Ethernet
bge2: interrupting at ivec 3796
bge2: HW config 00010115, 00000015, 00000000, 00000000 00000000
bge2: ASIC BCM5715 A3 (0x9003), Ethernet address 00:14:4f:ac:b7:0a
bge2: WARNING: failed to restrict dma range, falling back to parent bus dma range
bge2: setting short Tx thresholds
brgphy2 at bge2 phy 1: BCM5714 1000BASE-T/X media interface, rev. 0
brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge3 at pci10 dev 4 function 1: Broadcom BCM5714 Gigabit Ethernet
bge3: interrupting at ivec 3797
bge3: HW config 00000114, 00000014, 00000000, 00000000 00000000
bge3: ASIC BCM5715 A3 (0x9003), Ethernet address 00:14:4f:ac:b7:0a
bge3: WARNING: failed to restrict dma range, falling back to parent bus dma range
bge3: setting short Tx thresholds
brgphy3 at bge3 phy 1: BCM5714 1000BASE-T/X media interface, rev. 0
brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb10 at pci10 dev 8 function 0: ServerWorks HT1000 PCI/PCI-X Bridge (rev. 0xb4)
pci11 at ppb10 bus 13
pci11: i/o space, memory space enabled
mpt0 at pci11 dev 1 function 0: Symbios Logic SAS1064 (rev. 0x02)
mpt0: interrupting at ivec 1f8f
mpt0: Phy 0: Link Status Unknown
mpt0: Phy 0: Link Status Unknown
mpt0: Phy 0: Link Status Unknown
mpt0: Phy 0: Link Status Unknown
scsibus0 at mpt0: 63 targets, 8 luns per target
pyro1 at mainbus0: "Fire", rev 3, ign 7c0, bus B 2 to 4
pyro1: pci12 at pyro1
pci12: i/o space, memory space enabled
ppb11 at pci12 dev 0 function 0: Intel Serial to Parallel PCI Bridge A (rev. 0x09)
ppb11: PCI Express capability version 1 <PCI-E to PCI/PCI-X Bridge>
pci13 at ppb11 bus 3
pci13: i/o space, memory space enabled
ppb12 at pci12 dev 0 function 2: Intel Serial to Parallel PCI Bridge B (rev. 0x09)
ppb12: PCI Express capability version 1 <PCI-E to PCI/PCI-X Bridge>
pci14 at ppb12 bus 4
pci14: i/o space, memory space enabled
Emulex product 0xfc00 (Fiber Channel serial bus, revision 0x01) at pci14 dev 1 function 0 not configured
ebus1 at mainbus0: ign 7c0
flashprom at ebus1 addr 0-1fffff not configured
com0 at ebus1 addr 80-87 ipl 8: ns16550a, working fifo
com0: console
com1 at ebus1 addr 40-47 ipl 9: ns16550a, working fifo
rmc-comm at ebus1 addr 0-7 ipl a not configured
gpio at ebus1 addr c0-c0 not configured
env-monitor at ebus1 addr 0-80 not configured
power at ebus1 addr 40-c1 ipl 3 not configured
i2c at mainbus0 not configured
pcons at mainbus0 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "tick-counter" frequency 1504000000 Hz quality 100
timecounter: Timecounter "stick-counter" frequency 20000000 Hz quality 200
No counter-timer -- using %stick at 20MHz as system clock.
scsibus0: waiting 2 seconds for devices to settle...
uhub0 at usb0: Acer Labs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: Acer Labs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
uhub2 at usb2: Acer Labs EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 8 ports with 8 removable, self powered
sd0 at scsibus0 target 0 lun 0: <HITACHI, H101414SCSUN146G, SA23> disk fixed
sd0: 136 GB, 14089 cyl, 24 head, 848 sec, 512 bytes/sect x 286739329 sectors
sd0: tagged queueing
sd1 at scsibus0 target 1 lun 0: <HITACHI, H101414SCSUN146G, SA23> disk fixed
sd1: 136 GB, 14089 cyl, 24 head, 848 sec, 512 bytes/sect x 286739329 sectors
sd1: tagged queueing
ugen0 at uhub2 port 2
ugen0: Realtek 802.11n WLAN Adapter, rev 2.00/2.00, addr 2
Kernelized RAIDframe activated
root on sd0a dumps on sd0b
root file system type: ffs
WARNING: clock gained 2 days
uhub3 at uhub1 port 1: Atmel Standard USB Hub, class 9/0, rev 1.10/3.00, addr 2
uhub3: 4 ports with 4 removable, self powered
I expected to see an sd2 and sd3 as well.