Re: Any support yet for the UltraSPARC-III?

[Martin Husemann <martin%duskware.de@localhost>]

Below is a dmesg of my v210 booting todays -current. What problemd did
you run into?

Martin

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.55 (GENERIC) #1: Fri Aug  5 10:00:02 CEST 2011
        
martin%night-porter.duskware.de@localhost:/usr/src/sys/arch/sparc64/compile/GENERIC
total memory = 4096 MB
avail memory = 4010 MB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root): SUNW,Sun-Fire-V210 (Sun Fire V210): hostid 8345d5ed
cpu0 at mainbus0: SUNW,UltraSPARC-IIIi @ 1002 MHz, UPA id 0
cpu0: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
cpu1 at mainbus0: SUNW,UltraSPARC-IIIi @ 1002 MHz, UPA id 1
cpu1: 32K instruction (32 b/l), 64K data (32 b/l), 1024K external (64 b/l)
memory-controller at mainbus0 not configured
memory-controller at mainbus0 not configured
schizo0 at mainbus0: addr 4000ff00000: "Tomatillo", version 4, ign 7c0, bus B 0 
to 0
schizo0:  pci0 at schizo0
pci0: i/o space, memory space enabled
bge0 at pci0 dev 2 function 0: Broadcom BCM5704C Dual Gigabit Ethernet
bge0: interrupting at ivec 37c8
bge0: ASIC BCM5704 A3 (0x2003), Ethernet address 00:03:ba:45:d5:ed
brgphy0 at bge0 phy 1: BCM5704 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
bge1 at pci0 dev 2 function 1: Broadcom BCM5704C Dual Gigabit Ethernet
bge1: interrupting at ivec 37c9
bge1: ASIC BCM5704 A3 (0x2003), Ethernet address 00:03:ba:45:d5:ee
brgphy1 at bge1 phy 1: BCM5704 1000BASE-T media interface, rev. 0
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
schizo1 at mainbus0: addr 4000f600000: "Tomatillo", version 4, ign 780, bus A 0 
to 0
schizo1:  pci1 at schizo1
pci1: i/o space, memory space enabled
ebus0 at pci1 dev 7 function 0
ebus0: Acer Labs M1533 PCI-ISA Bridge, revision 0x00
flashprom at ebus0 addr 0-fffff, 290-290 not configured
rtc0 at ebus0 addr 70-71: mc146818 compatible time-of-day clock: m5819p
pcfiic0 at ebus0 addr 320-321 ipl 2e
iic0 at pcfiic0: I2C bus
i2c-bridge at iic0 addr 0x0b not configured
i2c-bridge at iic0 addr 0x0c not configured
motherboard-fru-prom at iic0 addr 0x51 not configured
chassis-fru-prom at iic0 addr 0x54 not configured
power-supply-fru-prom at iic0 addr 0x58 not configured
spdmem0 at iic0 addr 0x5b
spdmem0: DDR SDRAM (registered), data ECC, 512MB, 286MHz (PC-2300)
spdmem0: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 1-3-3-7
spdmem0: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
spdmem1 at iic0 addr 0x5c
spdmem1: DDR SDRAM (registered), data ECC, 512MB, 286MHz (PC-2300)
spdmem1: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 1-3-3-7
spdmem1: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
spdmem2 at iic0 addr 0x5d
spdmem2: DDR SDRAM (registered), data ECC, 512MB, 286MHz (PC-2300)
spdmem2: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns cycle time
spdmem2: tAA-tRCD-tRP-tRAS: 1-3-3-7
spdmem2: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
spdmem3 at iic0 addr 0x5e
spdmem3: DDR SDRAM (registered), data ECC, 512MB, 286MHz (PC-2300)
spdmem3: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns cycle time
spdmem3: tAA-tRCD-tRP-tRAS: 1-3-3-7
spdmem3: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
spdmem4 at iic0 addr 0x63
spdmem4: DDR SDRAM (registered), data ECC, 512MB, 286MHz (PC-2300)
spdmem4: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns cycle time
spdmem4: tAA-tRCD-tRP-tRAS: 1-3-3-7
spdmem4: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
spdmem5 at iic0 addr 0x64
spdmem5: DDR SDRAM (registered), data ECC, 512MB, 286MHz (PC-2300)
spdmem5: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns cycle time
spdmem5: tAA-tRCD-tRP-tRAS: 1-3-3-7
spdmem5: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
spdmem6 at iic0 addr 0x65
spdmem6: DDR SDRAM (registered), data ECC, 512MB, 286MHz (PC-2300)
spdmem6: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns cycle time
spdmem6: tAA-tRCD-tRP-tRAS: 1-3-3-7
spdmem6: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
spdmem7 at iic0 addr 0x66
spdmem7: DDR SDRAM (registered), data ECC, 512MB, 286MHz (PC-2300)
spdmem7: 13 rows, 11 cols, 1 ranks, 4 banks/chip, 7.0ns cycle time
spdmem7: tAA-tRCD-tRP-tRAS: 1-3-3-7
spdmem7: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
rscrtc at iic0 addr 0x68 not configured
nvram at iic0 addr 0x28 not configured
idprom at iic0 addr 0x28 not configured
gpio at iic0 addr 0x22 not configured
gpio at iic0 addr 0x23 not configured
gpio at iic0 addr 0x34 not configured
gpio at iic0 addr 0x38 not configured
power at ebus0 addr 800-82f ipl 20 not configured
com0 at ebus0 addr 3f8-3ff ipl 2c: ns16550a, working fifo
com0: console
com1 at ebus0 addr 2e8-2ef ipl 2c: ns16550a, working fifo
rmc-comm at ebus0 addr 3e8-3ef ipl 2c not configured
alipm has not been converted to device_t
alipm0 at pci1 dev 6 function 0: 223KHz clock
iic1 at alipm0: I2C bus
gpio at iic1 addr 0x45 not configured
ohci0 at pci1 dev 10 function 0: Acer Labs M5237 USB 1.1 Host Controller (rev. 
0x03)
ohci0: interrupting at ivec 7a7
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
aceride0 at pci1 dev 13 function 0: Acer Labs M5229 UDMA IDE Controller (rev. 
0xc4)
aceride0: bus-master DMA support present
aceride0: using PIO transfers above 137GB as workaround for 48bit DMA access 
bug, expect reduced performance
aceride0: primary channel configured to native-PCI mode
aceride0: using ivec 1f98 for native-PCI interrupt
atabus0 at aceride0 channel 0
aceride0: secondary channel configured to native-PCI mode
atabus1 at aceride0 channel 1
schizo2 at mainbus0: addr 4000e600000: "Tomatillo", version 4, ign 700, bus A 0 
to 0
schizo2:  pci2 at schizo2
pci2: i/o space, memory space enabled
esiop0 at pci2 dev 2 function 0: Symbios Logic 53c1010-66 (ultra3-wide scsi)
esiop0: using on-board RAM
esiop0: interrupting at ivec 1f29
scsibus0 at esiop0: 16 targets, 8 luns per target
esiop1 at pci2 dev 2 function 1: Symbios Logic 53c1010-66 (ultra3-wide scsi)
esiop1: using on-board RAM
esiop1: interrupting at ivec 1f28
scsibus1 at esiop1: 16 targets, 8 luns per target
schizo3 at mainbus0: addr 4000ef00000: "Tomatillo", version 4, ign 740, bus B 0 
to 0
schizo3:  pci3 at schizo3
pci3: i/o space, memory space enabled
bge2 at pci3 dev 2 function 0: Broadcom BCM5704C Dual Gigabit Ethernet
bge2: interrupting at ivec 375c
bge2: ASIC BCM5704 A3 (0x2003), Ethernet address 00:03:ba:45:d5:ef
brgphy2 at bge2 phy 1: BCM5704 1000BASE-T media interface, rev. 0
brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
bge3 at pci3 dev 2 function 1: Broadcom BCM5704C Dual Gigabit Ethernet
bge3: interrupting at ivec 375d
bge3: ASIC BCM5704 A3 (0x2003), Ethernet address 00:03:ba:45:d5:f0
brgphy3 at bge3 phy 1: BCM5704 1000BASE-T media interface, rev. 0
brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
pcons at mainbus0 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "tick-counter" frequency 1002000000 Hz quality 100
No counter-timer -- using %tick at 1002MHz as system clock.
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
uhub0 at usb0: Acer Labs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
sd0 at scsibus0 target 0 lun 0: <SEAGATE, ST336607LSUN36G, 0307> disk fixed
sd0: 34732 MB, 24622 cyl, 27 head, 107 sec, 512 bytes/sect x 71132959 sectors
sd0: sync (12.50ns offset 62), 16-bit (160.000MB/s) transfers, tagged queueing
sd1 at scsibus0 target 1 lun 0: <SEAGATE, ST336607LSUN36G, 0307> disk fixed
sd1: 34732 MB, 24622 cyl, 27 head, 107 sec, 512 bytes/sect x 71132959 sectors
sd1: sync (12.50ns offset 62), 16-bit (160.000MB/s) transfers, tagged queueing
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <DV-28E-B, , 1.2B> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(aceride0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
Kernelized RAIDframe activated
root on sd0a dumps on sd0b
root file system type: ffs