Re: Banana pi pro no video

[Ron Georgia <netverbs%gmail.com@localhost>]

Whoo hoo! I updated my pkgsrc, make install u-boot for bananapro and BAM! Video works! And I see my external drive:

shareverbs$ dmesg | grep wd
[     1.000006] sunxiwdt0 at simplebus1: Watchdog
[     1.000006] sunxiwdt0: default watchdog period is 16 seconds
[     3.087096] wd0 at atabus0 drive 0
[     3.097681] wd0: <Hitachi HUA723030ALA640>
[     3.097681] wd0: drive supports 16-sector PIO transfers, LBA48 addressing
[     3.097681] wd0: 2794 GB, 5814021 cyl, 16 head, 63 sec, 512 bytes/sect x 5860533168 sectors
[     3.157683] wd0: GPT GUID: f4c18c62-462d-416b-874b-1e76c3cd201c
[     3.167685] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags) w/PRIO
[     3.167685] wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 tags) w/PRIO

shareverbs# gpt show wd0
       start        size  index  contents
           0           1         PMBR
           1           1         Pri GPT header
           2          32         Pri GPT table
          34  5860533101         Unused
  5860533135          32         Sec GPT table
  5860533167           1         Sec GPT header

Thank you, thank you, thank you.

On 6/20/19, 10:06 AM, "Jason Thorpe" <thorpej%me.com@localhost> wrote:

    
    
    > On Jun 20, 2019, at 4:03 PM, Ron Georgia <netverbs%gmail.com@localhost> wrote:
    > 
    > Thank you very much. Compiling it now.
    > Sorry about that. I thought I was staying up to date with " cd /usr/pkgsrc &&  cvs update -dP"
    
    Note that if you are running a reasonably current -current, you can use installboot(8) (or the cross-tools nbinstallboot) to install the u-boot image onto the SD card / image.  It's a whole lot nicer / less-scary than using dd.
    
    > 
    > On 6/20/19, 9:50 AM, "Jason Thorpe" <thorpej%me.com@localhost> wrote:
    > 
    > 
    > 
    >> On Jun 20, 2019, at 3:03 PM, Ron Georgia <netverbs%gmail.com@localhost> wrote:
    >> 
    >> I do not see that in sysutils.
    >> $ /u/p/sysutils> ls | grep banana
    >> u-boot-bananapi
    >> u-boot-bananapi-m3
    >> u-boot-bananapi-r2
    >> 
    >> rgeorgia@clement /u/pkgsrc> sudo find . -type f | grep bananapro
    >> not found
    > 
    >    Your pkgsrc may be out of date; I added it on May 29:
    > 
    >    revision 1.1
    >    date: 2019-05-29 03:24:02 +0000;  author: thorpej;  state: Exp;  commitid: Bt9LqdFk6D5U53pB;
    >    Add a U-Boot package for the LeMaker Banana Pro.
    > 
    > 
    >> 
    >> On 6/20/19, 8:47 AM, "Jared McNeill" <jmcneill%invisible.ca@localhost> wrote:
    >> 
    >>   You cannot use U-boot for a different board and expect anything to work. 
    >>   Have you tried sysutils/u-boot-bananapro ?
    >> 
    >>   On Tue, 18 Jun 2019, Ron Georgia wrote:
    >> 
    >>> I am trying to install NetBSD on a Banana pi pro. I downloaded armv7 from http://nycdn.netbsd.org/pub/NetBSD-daily/HEAD/latest/evbarm-earmv7hf/binary/gzimg/armv7.img.gz
    >>> 
    >>> I dd the image to sd0d
    >>> $ sudo dd if=armv7_HEAD.img of=/dev/rsd0d bs=1m conv=sync
    >>> 
    >>> I then tried both bananapi u-boot image from =/usr/pkg/share/u-boot based on the wiki found here: https://wiki.netbsd.org/ports/evbarm/install_using_sysinst/
    >>> 
    >>> $ sudo dd if=/usr/pkg/share/u-boot/bananapi/u-boot-sunxi-with-spl.bin of=/dev/rsd0d bs=1k seek=8 conv=sync
    >>> $ sudo dd if=/usr/pkg/share/u-boot/bananapi-m3/u-boot-sunxi-with-spl.bin of=/dev/rsd0d bs=1k seek=8 conv=sync
    >>> 
    >>> Note: the documentation says of=/dev/rld0d bs=1k seek=8 conv=sync. Notice the rld0d not rsd0d. Is that right?
    >>> 
    >>> Any help is appreciated.
    >>> 
    >>> The boot.cmd does not match what the docs says it should be.
    >>> I looked at boot.cmd:
    >>> 
    >>> if test "${board}" = "am335x" ; then
    >>> 	setenv kernel netbsd-BEAGLEBONE.ub
    >>> 	setenv mmcpart 0:1
    >>> 	setenv bootargs root=ld0a
    >>> else
    >>> 	setenv use_efi 1
    >>> fi
    >>> 
    >>> if test "${soc}" = "tegra210" ; then
    >>> 	# enable PCIe
    >>> 	pci enum
    >>> fi
    >>> 
    >>> if test "${use_efi}" = "1" ; then
    >>> 	setenv boot_scripts
    >>> 	setenv boot_script_dhcp
    >>> 	run distro_bootcmd
    >>> else
    >>> 	fatload mmc ${mmcpart} ${kernel_addr_r} ${kernel}
    >>> 	bootm ${kernel_addr_r} ${bootargs}
    >>> fi
    >>> 
    >>> ================================ boot.ini ================================
    >>> ODROIDC-UBOOT-CONFIG
    >>> 
    >>> setenv bootargs "awge0.mac-address=${ethaddr}"
    >>> setenv bootcmd "fatload mmc 0:1 0x21000000 netbsd-GENERIC.ub; fatload mmc 0:1 0x20000000 meson8b-odroidc1.dtb; bootm 0x21000000 - 0x20000000"
    >>> run bootcmd
    >>> 
    >>> ================================ cmdline.txt ================================
    >>> root=ld0a console=fb
    >>> #fb=1280x1024		# to select a mode, otherwise try EDID
    >>> #fb=disable		# to disable fb completely
    >>> 
    >>> ================================ Config.txt ================================
    >>> # Boot options, see https://www.raspberrypi.org/documentation/configuration/config-txt/boot.md
    >>> kernel_address=0x01000040
    >>> # UART settings, see https://www.raspberrypi.org/documentation/configuration/uart.md
    >>> enable_uart=1
    >>> force_turbo=0
    >>> 
    >>> 
    >>> Ron Georgia
    >>> “90% of my problems are due to ignorance, the other 10% is because I just don’t know any better.”
    >>> 
    >>> 
    >>> 
    >>> 
    >>> 
    >>> 
    >> 
    >> 
    > 
    >    -- thorpej
    > 
    > 
    > 
    > 
    
    -- thorpej