I do not see that in sysutils.
$ /u/p/sysutils> ls | grep banana
u-boot-bananapi
u-boot-bananapi-m3
u-boot-bananapi-r2
rgeorgia@clement /u/pkgsrc> sudo find . -type f | grep bananapro
not found
On 6/20/19, 8:47 AM, "Jared McNeill" <jmcneill%invisible.ca@localhost> wrote:
You cannot use U-boot for a different board and expect anything to work.
Have you tried sysutils/u-boot-bananapro ?
On Tue, 18 Jun 2019, Ron Georgia wrote:
> I am trying to install NetBSD on a Banana pi pro. I downloaded armv7 from http://nycdn.netbsd.org/pub/NetBSD-daily/HEAD/latest/evbarm-earmv7hf/binary/gzimg/armv7.img.gz
>
> I dd the image to sd0d
> $ sudo dd if=armv7_HEAD.img of=/dev/rsd0d bs=1m conv=sync
>
> I then tried both bananapi u-boot image from =/usr/pkg/share/u-boot based on the wiki found here: https://wiki.netbsd.org/ports/evbarm/install_using_sysinst/
>
> $ sudo dd if=/usr/pkg/share/u-boot/bananapi/u-boot-sunxi-with-spl.bin of=/dev/rsd0d bs=1k seek=8 conv=sync
> $ sudo dd if=/usr/pkg/share/u-boot/bananapi-m3/u-boot-sunxi-with-spl.bin of=/dev/rsd0d bs=1k seek=8 conv=sync
>
> Note: the documentation says of=/dev/rld0d bs=1k seek=8 conv=sync. Notice the rld0d not rsd0d. Is that right?
>
> Any help is appreciated.
>
> The boot.cmd does not match what the docs says it should be.
> I looked at boot.cmd:
>
> if test "${board}" = "am335x" ; then
> setenv kernel netbsd-BEAGLEBONE.ub
> setenv mmcpart 0:1
> setenv bootargs root=ld0a
> else
> setenv use_efi 1
> fi
>
> if test "${soc}" = "tegra210" ; then
> # enable PCIe
> pci enum
> fi
>
> if test "${use_efi}" = "1" ; then
> setenv boot_scripts
> setenv boot_script_dhcp
> run distro_bootcmd
> else
> fatload mmc ${mmcpart} ${kernel_addr_r} ${kernel}
> bootm ${kernel_addr_r} ${bootargs}
> fi
>
> ================================ boot.ini ================================
> ODROIDC-UBOOT-CONFIG
>
> setenv bootargs "awge0.mac-address=${ethaddr}"
> setenv bootcmd "fatload mmc 0:1 0x21000000 netbsd-GENERIC.ub; fatload mmc 0:1 0x20000000 meson8b-odroidc1.dtb; bootm 0x21000000 - 0x20000000"
> run bootcmd
>
> ================================ cmdline.txt ================================
> root=ld0a console=fb
> #fb=1280x1024 # to select a mode, otherwise try EDID
> #fb=disable # to disable fb completely
>
> ================================ Config.txt ================================
> # Boot options, see https://www.raspberrypi.org/documentation/configuration/config-txt/boot.md
> kernel_address=0x01000040
> # UART settings, see https://www.raspberrypi.org/documentation/configuration/uart.md
> enable_uart=1
> force_turbo=0
>
>
> Ron Georgia
> “90% of my problems are due to ignorance, the other 10% is because I just don’t know any better.”
>
>
>
>
>
>