Port-alpha archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
RE: The problems in src/sys/dev/ic/isp.c
Hi all,
FYI
I tested the installation CDs with and without patches on a Personal Workstation 600a and XP1000.
All the results showed that everything booted up without any problems.
1)Personal Workstation 600a
>>>show config
Firmware
SRM Console: V7.2-1 Mar 6 2000 14:47:02
ARC Console: 5.70
PALcode: OpenVMS PALcode V1.20-16, Tru64 UNIX PALcode V1.22-18
SROM Version: v5.90
Processor
DECchip (tm) 21164A-2 Pass 600 MHz 96 KBytes SCache
2 MB BCache
PYXIS ASIC Pass 257
MEMORY
Memory Size = 1536Mb
Bank Size/Sets Base Addr
------ ---------- ---------
0 512Mb 00000000
1 512Mb 20000000
2 512Mb 40000000
BCache Size = 2Mb
Tested Memory = 1536Mbytes
PCI Bus
Bus 00 Slot 03: Digital Semiconductor 21143 Network Controller
ewa0.0.0.3.0 00-00-F8-75-C8-24
Bus 00 Slot 04: PCI IDE
pqb0.0.1.4.0 PCI EIDE
dka0.0.0.4.0 401248 C DRW
Bus 00 Slot 07: Intel SIO 82378
Bus 00 Slot 20: DECchip 21152 PCI to PCI Bridge
Bus 01 Slot 08: NCR 895 Scsi Controller
pkc0.7.0.1008.0 SCSI Bus ID 7
dkc0.0.0.1008.0 SEAGATE ST336607LW
Bus 01 Slot 09: ISP1040 Scsi Controller
pkd0.7.0.1009.0 SCSI Bus ID 7
dkd0.0.0.1009.0 SEAGATE ST39102LW
dkd300.3.0.1009.0 SEAGATE ST39102LW
dkd400.4.0.1009.0 IBM DDRS-39130W
Bus 01 Slot 10: Matrox Millenium II
ISA
Slot Device Name Type Enabled BaseAddr IRQ DMA
0
0 MOUSE Embedded Yes 60 12
1 KBD Embedded Yes 60 1
2 COM1 Embedded Yes 3f8 4
3 COM2 Embedded Yes 2f8 3
4 LPT1 Embedded Yes 3bc 7
5 FLOPPY Embedded Yes 3f0 6 2
6 EIDE Embedded Yes 1f0 14
3f6 15
170
376
7 ES1888 Embedded Yes 220 5 1
1-1)20260214081227Z daily image
>>>boot dka0 -fl A
(boot dka0.0.0.4.0 -flags A)
block 0 of dka0.0.0.4.0 is a valid boot block
reading 13 blocks from dka0.0.0.4.0
bootstrap code read in
base = 1d8000, image_start = 0, image_bytes = 1a00
initializing HWRPB at 2000
initializing page table at 1ca000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
NetBSD/alpha 11.99.5 ISO 9660 Primary Bootstrap
Jumping to entry point...
NetBSD/alpha 11.99.5 Secondary Bootstrap, Revision 1.13 (Sat Feb 14 08:12:27 UTC 2026)
VMS PAL rev: 0x1000000010114
OSF PAL rev: 0x1000000020116
Switch to OSF PAL code succeeded.
Boot flags: A
11312480+255344=0xb08980
Entering netbsd at 0xfffffc0000a01410...
[ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[ 1.0000000] 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[ 1.0000000] 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[ 1.0000000] 2024, 2025, 2026
[ 1.0000000] The NetBSD Foundation, Inc. All rights reserved.
[ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.0000000] The Regents of the University of California. All rights reserved.
[ 1.0000000] NetBSD 11.99.5 (INSTALL) #0: Sat Feb 14 08:12:27 UTC 2026
[ 1.0000000] mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/alpha/compile/INSTALL
[ 1.0000000] Digital Personal WorkStation 600au, 598MHz
[ 1.0000000] 8192 byte page size, 1 processor.
[ 1.0000000] total memory = 1536 MB
[ 1.0000000] (1896 KB reserved for PROM, 1534 MB used by NetBSD)
[ 1.0000000] avail memory = 1501 MB
[ 1.0000000] mainbus0 (root)
[ 1.0000000] cpu0 at mainbus0: ID 0 (primary), 21164A-0 (EV56)
[ 1.0000000] cpu0: Architecture extensions: 0x1<BWX>
[ 1.0000000] cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 2
[ 1.0000000] cia0: extended capabilities: 0x1<BWEN>
[ 1.0000000] cia0: using BWX for PCI config access
[ 1.0000000] cia0: WARNING: Pyxis pass 1 DMA bug; no bets...
[ 1.0000000] pci0 at cia0 bus 0
[ 1.0000000] tlp0 at pci0 dev 3 function 0: DECchip 21143 Ethernet, pass 3.0
[ 1.0000000] tlp0: interrupting at dec 550 irq 0
[ 1.0000000] tlp0: DEC, Ethernet address 00:00:f8:75:c8:24
[ 1.0000000] nsphy0 at tlp0 phy 5: DP83840 10/100 media interface, rev. 1
[ 1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[ 1.0000000] tlp0: 10baseT, 10baseT-FDX, 10base2, 10base5
[ 1.0000000] cmdide0 at pci0 dev 4 function 0: CMD Technology PCI0646 (rev. 0x01)
[ 1.0000000] cmdide0: primary channel wired to compatibility mode, channel non-independent
[ 1.0000000] cmdide0: primary channel interrupting at isa irq 14
[ 1.0000000] atabus0 at cmdide0 channel 0
[ 1.0000000] cmdide0: secondary channel wired to compatibility mode, channel non-independent
[ 1.0000000] cmdide0: secondary channel ignored (disabled)
[ 1.0000000] sio0 at pci0 dev 7 function 0: vendor 8086 product 0484 (rev. 0x43)
[ 1.0000000] ppb0 at pci0 dev 20 function 0: vendor 1011 product 0024 (rev. 0x02)
[ 1.0000000] pci1 at ppb0 bus 1
[ 1.0000000] siop0 at pci1 dev 8 function 0: Symbios Logic 53c895 (ultra2-wide scsi)
[ 1.0000000] siop0: using on-board RAM
[ 1.0000000] siop0: interrupting at dec 550 irq 12
[ 1.0000000] scsibus0 at siop0: 16 targets, 8 luns per target
[ 1.0000000] isp0 at pci1 dev 9 function 0: QLogic 1020 Fast Wide SCSI HBA
[ 1.0000000] isp0: interrupting at dec 550 irq 16
[ 1.0000000] vga0 at pci1 dev 10 function 0: vendor 102b product 051b (rev. 0x00)
[ 1.0000000] wsdisplay0 at vga0 (kbdmux ignored)
[ 1.0000000] drm at vga0 not configured
[ 1.0000000] isa0 at sio0
[ 1.0000000] com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, 16-byte FIFO
[ 1.0000000] com0: console
[ 1.0000000] com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 16-byte FIFO
[ 1.0000000] lpt0 at isa0 port 0x3bc-0x3bf irq 7
[ 1.0000000] pckbc0 at isa0 port 0x60-0x64
[ 1.0000000] pckbd0 at pckbc0 (kbd slot)
[ 1.0000000] pckbc0: using irq 1 for kbd slot
[ 1.0000000] wskbd0 at pckbd0 (mux ignored)
[ 1.0000000] pms0 at pckbc0 (aux slot)
[ 1.0000000] pckbc0: using irq 12 for aux slot
[ 1.0000000] wsmouse0 at pms0 (mux ignored)
[ 1.0000000] fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
[ 1.0000000] mcclock0 at isa0 port 0x70-0x71: mc146818 compatible time-of-day clock
[ 1.0000000] WARNING: system needs entropy for security; see entropy(7)
[ 1.0095637] stray isa irq 14
[ 1.0427927] stray isa irq 14
[ 1.0770299] scsibus0: waiting 2 seconds for devices to settle...
[ 1.1486262] scsibus1 at isp0: 16 targets, 8 luns per target
[ 1.2156159] atapibus0 at atabus0: 2 targets
[ 1.2648289] stray isa irq 14
[ 1.3035000] scsibus1: waiting 2 seconds for devices to settle...
[ 1.3738761] cd0 at atapibus0 drive 0: <401248 CDRW, 2J18NE0121, 1.0D> cdrom removable
[ 3.4596929] sd0 at scsibus0 target 0 lun 0: <SEAGATE, ST336607LW, DS09> disk fixed
[ 3.5495362] sd0: 34732 MB, 49855 cyl, 2 head, 713 sec, 512 bytes/sect x 71132959 sectors
[ 3.6452348] sd0: sync (25.00ns offset 31), 16-bit (80.000MB/s) transfers, tagged queueing
[ 3.9772564] fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
[ 7.9000079] sd1 at scsibus1 target 0 lun 0: <SEAGATE, ST39102LW, 8320> disk fixed
[ 7.9898510] sd1: 8683 MB, 6962 cyl, 12 head, 212 sec, 512 bytes/sect x 17783240 sectors
[ 8.0884795] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 9.1948958] sd2 at scsibus1 target 3 lun 0: <SEAGATE, ST39102LW, 0004> disk fixed
[ 9.2847385] sd2: 8683 MB, 6962 cyl, 12 head, 212 sec, 512 bytes/sect x 17783240 sectors
[ 9.3833672] sd2: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 9.4888341] sd3 at scsibus1 target 4 lun 0: <IBM, DDRS-39130W, S97B> disk fixed
[ 9.6636350] sd3: 8715 MB, 8387 cyl, 10 head, 212 sec, 512 bytes/sect x 17850000 sectors
[ 9.7622639] sd3: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 15.0121304] WARNING: 1 error while detecting hardware; check system log.
[ 15.0910640] WARNING: can't figure what device matches "SCSI 0 4 0 0 0 0 0"
[ 15.1732609] root on md0a dumps on md0b
[ 15.2181865] root file system type: ffs
[ 15.2622590] kern.module.path=/stand/alpha/11.99.5/modules
[ 15.3344009] entropy: best effort
Terminal type? [vt100]
Erase set to backspace.
erase ^?, werase ^W, kill ^U, intr ^C
1-2)John's patched 11.0_RC1 image
>>>boot dka0 -fl A
(boot dka0.0.0.4.0 -flags A)
block 0 of dka0.0.0.4.0 is a valid boot block
reading 13 blocks from dka0.0.0.4.0
bootstrap code read in
base = 1d8000, image_start = 0, image_bytes = 1a00
initializing HWRPB at 2000
initializing page table at 1ca000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
NetBSD/alpha 11.0_RC1 ISO 9660 Primary Bootstrap
Jumping to entry point...
NetBSD/alpha 11.0_RC1 Secondary Bootstrap, Revision 1.13 (Tue Feb 17 02:52:46 UTC 2026)
VMS PAL rev: 0x1000000010114
OSF PAL rev: 0x1000000020116
Switch to OSF PAL code succeeded.
Boot flags: A
11290976+255344=0xb034d0
Entering netbsd at 0xfffffc0000a01410...
[ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[ 1.0000000] 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[ 1.0000000] 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[ 1.0000000] 2024, 2025, 2026
[ 1.0000000] The NetBSD Foundation, Inc. All rights reserved.
[ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.0000000] The Regents of the University of California. All rights reserved.
[ 1.0000000] NetBSD 11.0_RC1 (INSTALL) #0: Tue Feb 17 02:57:57 UTC 2026
[ 1.0000000] john%platypus.zia.io@localhost:/usr/obj-alpha/sys/arch/alpha/compile/INSTALL
[ 1.0000000] Digital Personal WorkStation 600au, 598MHz
[ 1.0000000] 8192 byte page size, 1 processor.
[ 1.0000000] total memory = 1536 MB
[ 1.0000000] (1896 KB reserved for PROM, 1534 MB used by NetBSD)
[ 1.0000000] avail memory = 1501 MB
[ 1.0000000] mainbus0 (root)
[ 1.0000000] cpu0 at mainbus0: ID 0 (primary), 21164A-0 (EV56)
[ 1.0000000] cpu0: Architecture extensions: 0x1<BWX>
[ 1.0000000] cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 2
[ 1.0000000] cia0: extended capabilities: 0x1<BWEN>
[ 1.0000000] cia0: using BWX for PCI config access
[ 1.0000000] cia0: WARNING: Pyxis pass 1 DMA bug; no bets...
[ 1.0000000] pci0 at cia0 bus 0
[ 1.0000000] tlp0 at pci0 dev 3 function 0: DECchip 21143 Ethernet, pass 3.0
[ 1.0000000] tlp0: interrupting at dec 550 irq 0
[ 1.0000000] tlp0: DEC, Ethernet address 00:00:f8:75:c8:24
[ 1.0000000] nsphy0 at tlp0 phy 5: DP83840 10/100 media interface, rev. 1
[ 1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[ 1.0000000] tlp0: 10baseT, 10baseT-FDX, 10base2, 10base5
[ 1.0000000] cmdide0 at pci0 dev 4 function 0: CMD Technology PCI0646 (rev. 0x01)
[ 1.0000000] cmdide0: primary channel wired to compatibility mode, channel non-independent
[ 1.0000000] cmdide0: primary channel interrupting at isa irq 14
[ 1.0000000] atabus0 at cmdide0 channel 0
[ 1.0000000] cmdide0: secondary channel wired to compatibility mode, channel non-independent
[ 1.0000000] cmdide0: secondary channel ignored (disabled)
[ 1.0000000] sio0 at pci0 dev 7 function 0: vendor 8086 product 0484 (rev. 0x43)
[ 1.0000000] ppb0 at pci0 dev 20 function 0: vendor 1011 product 0024 (rev. 0x02)
[ 1.0000000] pci1 at ppb0 bus 1
[ 1.0000000] siop0 at pci1 dev 8 function 0: Symbios Logic 53c895 (ultra2-wide scsi)
[ 1.0000000] siop0: using on-board RAM
[ 1.0000000] siop0: interrupting at dec 550 irq 12
[ 1.0000000] scsibus0 at siop0: 16 targets, 8 luns per target
[ 1.0000000] isp0 at pci1 dev 9 function 0: QLogic 1020 Fast Wide SCSI HBA
[ 1.0000000] isp0: interrupting at dec 550 irq 16
[ 1.0000000] vga0 at pci1 dev 10 function 0: vendor 102b product 051b (rev. 0x00)
[ 1.0000000] wsdisplay0 at vga0 (kbdmux ignored)
[ 1.0000000] drm at vga0 not configured
[ 1.0000000] isa0 at sio0
[ 1.0000000] lpt0 at isa0 port 0x3bc-0x3bf irq 7
[ 1.0000000] com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, 16-byte FIFO
[ 1.0000000] com0: console
[ 1.0000000] com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 16-byte FIFO
[ 1.0000000] pckbc0 at isa0 port 0x60-0x64
[ 1.0000000] pckbd0 at pckbc0 (kbd slot)
[ 1.0000000] pckbc0: using irq 1 for kbd slot
[ 1.0000000] wskbd0 at pckbd0 (mux ignored)
[ 1.0000000] pms0 at pckbc0 (aux slot)
[ 1.0000000] pckbc0: using irq 12 for aux slot
[ 1.0000000] wsmouse0 at pms0 (mux ignored)
[ 1.0000000] fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
[ 1.0000000] mcclock0 at isa0 port 0x70-0x71: mc146818 compatible time-of-day clock
[ 1.0000000] WARNING: system needs entropy for security; see entropy(7)
[ 1.0095470] stray isa irq 14
[ 1.0428199] stray isa irq 14
[ 1.0770580] scsibus0: waiting 2 seconds for devices to settle...
[ 1.1486571] scsibus1 at isp0: 16 targets, 8 luns per target
[ 1.2156149] atapibus0 at atabus0: 2 targets
[ 1.2648662] stray isa irq 14
[ 1.3035002] scsibus1: waiting 2 seconds for devices to settle...
[ 1.3739186] cd0 at atapibus0 drive 0: <401248 CDRW, 2J18NE0121, 1.0D> cdrom removable
[ 3.4598045] sd0 at scsibus0 target 0 lun 0: <SEAGATE, ST336607LW, DS09> disk fixed
[ 3.5496495] sd0: 34732 MB, 49855 cyl, 2 head, 713 sec, 512 bytes/sect x 71132959 sectors
[ 3.6453581] sd0: sync (25.00ns offset 31), 16-bit (80.000MB/s) transfers, tagged queueing
[ 3.9773920] fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
[ 7.8759313] sd1 at scsibus1 target 0 lun 0: <SEAGATE, ST39102LW, 8320> disk fixed
[ 7.9657745] sd1: 8683 MB, 6962 cyl, 12 head, 212 sec, 512 bytes/sect x 17783240 sectors
[ 8.0644101] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 9.1699054] sd2 at scsibus1 target 3 lun 0: <SEAGATE, ST39102LW, 0004> disk fixed
[ 9.2607292] sd2: 8683 MB, 6962 cyl, 12 head, 212 sec, 512 bytes/sect x 17783240 sectors
[ 9.3583880] sd2: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 9.4648355] sd3 at scsibus1 target 4 lun 0: <IBM, DDRS-39130W, S97B> disk fixed
[ 9.6406186] sd3: 8715 MB, 8387 cyl, 10 head, 212 sec, 512 bytes/sect x 17850000 sectors
[ 9.7392544] sd3: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 14.9913435] WARNING: 1 error while detecting hardware; check system log.
[ 15.0695681] WARNING: can't figure what device matches "SCSI 0 4 0 0 0 0 0"
[ 15.1515361] root on md0a dumps on md0b
[ 15.1964282] root file system type: ffs
[ 15.2407739] kern.module.path=/stand/alpha/11.0/modules
[ 15.3106948] entropy: best effort
Terminal type? [vt100]
Erase set to backspace.
erase ^?, werase ^W, kill ^U, intr ^C
1-3)Thorpej's patched image
>>>boot dka0 -fl A
(boot dka0.0.0.4.0 -flags A)
block 0 of dka0.0.0.4.0 is a valid boot block
reading 13 blocks from dka0.0.0.4.0
bootstrap code read in
base = 1d8000, image_start = 0, image_bytes = 1a00
initializing HWRPB at 2000
initializing page table at 1ca000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
NetBSD/alpha 11.99.5 ISO 9660 Primary Bootstrap
Jumping to entry point...
NetBSD/alpha 11.99.5 Secondary Bootstrap, Revision 1.13 (Wed Apr 22 03:25:12 UTC 2026)
VMS PAL rev: 0x1000000010114
OSF PAL rev: 0x1000000020116
Switch to OSF PAL code succeeded.
Boot flags: A
11314192+254592=0xb08d40
Entering netbsd at 0xfffffc0000a01410...
[ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[ 1.0000000] 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[ 1.0000000] 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[ 1.0000000] 2024, 2025, 2026
[ 1.0000000] The NetBSD Foundation, Inc. All rights reserved.
[ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.0000000] The Regents of the University of California. All rights reserved.
[ 1.0000000] NetBSD 11.99.5 (INSTALL) #1: Wed Apr 22 04:27:07 PDT 2026
[ 1.0000000] thorpej@the-ripe-vessel:/nbsd/objdir/alpha/sys/arch/alpha/compile/INSTALL
[ 1.0000000] Digital Personal WorkStation 600au, 598MHz
[ 1.0000000] 8192 byte page size, 1 processor.
[ 1.0000000] total memory = 1536 MB
[ 1.0000000] (1896 KB reserved for PROM, 1534 MB used by NetBSD)
[ 1.0000000] avail memory = 1501 MB
[ 1.0000000] mainbus0 (root)
[ 1.0000000] cpu0 at mainbus0: ID 0 (primary), 21164A-0 (EV56)
[ 1.0000000] cpu0: Architecture extensions: 0x1<BWX>
[ 1.0000000] cia0 at mainbus0: DECchip 2117x Core Logic Chipset (Pyxis), pass 2
[ 1.0000000] cia0: extended capabilities: 0x1<BWEN>
[ 1.0000000] cia0: using BWX for PCI config access
[ 1.0000000] cia0: WARNING: Pyxis pass 1 DMA bug; no bets...
[ 1.0000000] pci0 at cia0 bus 0
[ 1.0000000] tlp0 at pci0 dev 3 function 0: DECchip 21143 Ethernet, pass 3.0
[ 1.0000000] tlp0: interrupting at dec 550 irq 0
[ 1.0000000] tlp0: DEC, Ethernet address 00:00:f8:75:c8:24
[ 1.0000000] nsphy0 at tlp0 phy 5: DP83840 10/100 media interface, rev. 1
[ 1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[ 1.0000000] tlp0: 10baseT, 10baseT-FDX, 10base2, 10base5
[ 1.0000000] cmdide0 at pci0 dev 4 function 0: CMD Technology PCI0646 (rev. 0x01)
[ 1.0000000] cmdide0: primary channel wired to compatibility mode, channel non-independent
[ 1.0000000] cmdide0: primary channel interrupting at isa irq 14
[ 1.0000000] atabus0 at cmdide0 channel 0
[ 1.0000000] cmdide0: secondary channel wired to compatibility mode, channel non-independent
[ 1.0000000] cmdide0: secondary channel ignored (disabled)
[ 1.0000000] sio0 at pci0 dev 7 function 0: vendor 8086 product 0484 (rev. 0x43)
[ 1.0000000] ppb0 at pci0 dev 20 function 0: vendor 1011 product 0024 (rev. 0x02)
[ 1.0000000] pci1 at ppb0 bus 1
[ 1.0000000] siop0 at pci1 dev 8 function 0: Symbios Logic 53c895 (ultra2-wide scsi)
[ 1.0000000] siop0: using on-board RAM
[ 1.0000000] siop0: interrupting at dec 550 irq 12
[ 1.0000000] scsibus0 at siop0: 16 targets, 8 luns per target
[ 1.0000000] isp0 at pci1 dev 9 function 0: QLogic 1020 Fast Wide SCSI HBA
[ 1.0000000] isp0: interrupting at dec 550 irq 16
[ 1.0000000] vga0 at pci1 dev 10 function 0: vendor 102b product 051b (rev. 0x00)
[ 1.0000000] wsdisplay0 at vga0 (kbdmux ignored)
[ 1.0000000] drm at vga0 not configured
[ 1.0000000] isa0 at sio0
[ 1.0000000] com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, 16-byte FIFO
[ 1.0000000] com0: console
[ 1.0000000] com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 16-byte FIFO
[ 1.0000000] lpt0 at isa0 port 0x3bc-0x3bf irq 7
[ 1.0000000] pckbc0 at isa0 port 0x60-0x64
[ 1.0000000] pckbd0 at pckbc0 (kbd slot)
[ 1.0000000] pckbc0: using irq 1 for kbd slot
[ 1.0000000] wskbd0 at pckbd0 (mux ignored)
[ 1.0000000] pms0 at pckbc0 (aux slot)
[ 1.0000000] pckbc0: using irq 12 for aux slot
[ 1.0000000] wsmouse0 at pms0 (mux ignored)
[ 1.0000000] fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
[ 1.0000000] mcclock0 at isa0 port 0x70-0x71: mc146818 compatible time-of-day clock
[ 1.0000000] WARNING: system needs entropy for security; see entropy(7)
[ 1.0099026] stray isa irq 14
[ 1.0431099] stray isa irq 14
[ 1.0772963] scsibus0: waiting 2 seconds for devices to settle...
[ 1.1487318] scsibus1 at isp0: 16 targets, 8 luns per target
[ 1.2159677] atapibus0 at atabus0: 2 targets
[ 1.2649451] stray isa irq 14
[ 1.3038537] scsibus1: waiting 2 seconds for devices to settle...
[ 1.3741694] cd0 at atapibus0 drive 0: <401248 CDRW, 2J18NE0121, 1.0D> cdrom removable
[ 3.4591627] sd0 at scsibus0 target 0 lun 0: <SEAGATE, ST336607LW, DS09> disk fixed
[ 3.5490080] sd0: 34732 MB, 49855 cyl, 2 head, 713 sec, 512 bytes/sect x 71132959 sectors
[ 3.6447148] sd0: sync (25.00ns offset 31), 16-bit (80.000MB/s) transfers, tagged queueing
[ 3.9757699] fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
[ 7.9045548] sd1 at scsibus1 target 0 lun 0: <SEAGATE, ST39102LW, 8320> disk fixed
[ 7.9943991] sd1: 8683 MB, 6962 cyl, 12 head, 212 sec, 512 bytes/sect x 17783240 sectors
[ 8.0920548] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 9.1985200] sd2 at scsibus1 target 3 lun 0: <SEAGATE, ST39102LW, 0004> disk fixed
[ 9.2893430] sd2: 8683 MB, 6962 cyl, 12 head, 212 sec, 512 bytes/sect x 17783240 sectors
[ 9.3869979] sd2: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 9.4934438] sd3 at scsibus1 target 4 lun 0: <IBM, DDRS-39130W, S97B> disk fixed
[ 9.6643452] sd3: 8715 MB, 8387 cyl, 10 head, 212 sec, 512 bytes/sect x 17850000 sectors
[ 9.7629803] sd3: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 15.0150284] WARNING: 1 error while detecting hardware; check system log.
[ 15.0939539] WARNING: can't figure what device matches "SCSI 0 4 0 0 0 0 0"
[ 15.1761649] root on md0a dumps on md0b
[ 15.2210937] root file system type: ffs
[ 15.2651562] kern.module.path=/stand/alpha/11.99.5/modules
[ 15.3294881] entropy: best effort
Terminal type? [vt100]
Erase set to backspace.
erase ^?, werase ^W, kill ^U, intr ^C
2)XP1000
>>>show config
Compaq Computer Corporation
COMPAQ Professional Workstation XP1000
Firmware
SRM Console: V5.9-1 Dec 14 2000 16:04:15
ARC Console: 5.70
PALcode: OpenVMS PALcode V1.88-27, Tru64 UNIX PALcode V1.83-22
Serial Rom: SROM B1a
PIC: 0.36
Processor
DECchip (tm) 21264A-8 667MHz
Memory
2048 MBytes of System Memory
Bank Size Base Addr Dimms
------ ---------- --------- -----
0 1024 MBytes 40000000 1111
1 1024 MBytes 00000000 1111
BCache Size = 4 MBytes
Slot Option Hose 0, Bus 0, PCI
7/0 Cypress 82C693 Bridge to Bus 1, ISA
7/1 Cypress 82C693 IDE dqa.0.0.107.0
dqa0.0.0.107.0 MATSHITA DVD-RAM SW-9585
7/2 Cypress 82C693 IDE dqb.0.1.207.0
7/3 Cypress 82C693 USB
11/0 00301000/10101000
11/1 00301000/10101000
12 51571002/2036148C
13 10088086/11078086
Slot Option Hose 1, Bus 0, PCI
3 DECchip 21143-AA ewa0.0.0.3.1 08-00-2B-87-1D-B2
6 QLogic ISP10x0 pka0.7.0.6.1 SCSI Bus ID 7
dka100.1.0.6.1 QUANTUM ATLAS 10K 9WLS
8 DECchip 21152-AA Bridge to Bus 2, PCI
Slot Option Hose 1, Bus 2, PCI
9/0 30381106/02161145
9/1 30381106/02161145
9/2 31041106/02171145
9/3 30441106/304414DB
ISA
Slot Device Name Type Enabled BaseAddr IRQ DMA
0
0 MOUSE Embedded Yes 60 12
1 KBD Embedded Yes 60 1
2 COM1 Embedded Yes 3f8 4
3 COM2 Embedded Yes 2f8 3
4 LPT1 Embedded Yes 3bc 7
5 FLOPPY Embedded Yes 3f0 6 2
6 EIDE Embedded Yes 1f0 14
3f6 15
170
376
7 ES1888 Embedded Yes 220 5 1
5
8 USB Embedded Yes 10
2-1)20260214081227Z daily image
>>>boot dqa0 -fl A
(boot dqa0.0.0.107.0 -flags A)
block 0 of dqa0.0.0.107.0 is a valid boot block
reading 13 blocks from dqa0.0.0.107.0
bootstrap code read in
base = 1b2000, image_start = 0, image_bytes = 1a00
initializing HWRPB at 2000
initializing page table at 7ffee000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
NetBSD/alpha 11.99.5 ISO 9660 Primary Bootstrap
Jumping to entry point...
NetBSD/alpha 11.99.5 Secondary Bootstrap, Revision 1.13 (Sat Feb 14 08:12:27 UTC 2026)
VMS PAL rev: 0x1001b00010158
OSF PAL rev: 0x1001600020153
Switch to OSF PAL code succeeded.
Boot flags: A
11312480+255344=0xb08980
Entering netbsd at 0xfffffc0000a01410...
[ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[ 1.0000000] 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[ 1.0000000] 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[ 1.0000000] 2024, 2025, 2026
[ 1.0000000] The NetBSD Foundation, Inc. All rights reserved.
[ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.0000000] The Regents of the University of California. All rights reserved.
[ 1.0000000] NetBSD 11.99.5 (INSTALL) #0: Sat Feb 14 08:12:27 UTC 2026
[ 1.0000000] mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/alpha/compile/INSTALL
[ 1.0000000] COMPAQ Professional Workstation XP1000, 666MHz, s/n AY0
[ 1.0000000] 8192 byte page size, 1 processor.
[ 1.0000000] total memory = 2048 MB
[ 1.0000000] (1816 KB reserved for PROM, 2046 MB used by NetBSD)
[ 1.0000000] avail memory = 2006 MB
[ 1.0000000] mainbus0 (root)
[ 1.0000000] cpu0 at mainbus0: ID 0 (primary), 21264A-8 (EV67)
[ 1.0000000] cpu0: Architecture extensions: 0x307<PAT,MVI,CIX,FIX,BWX>
[ 1.0000000] tsc0 at mainbus0: 21272 Core Logic Chipset, Cchip rev 0
[ 1.0000000] tsc0: 4 Dchips, 1 memory bus of 32 bytes
[ 1.0000000] tsc0: arrays present: 1024MB, 1024MB (split), 0MB, 0MB, Dchip 0 rev 1
[ 1.0000000] tsp0 at tsc0
[ 1.0000000] pci0 at tsp0 bus 0
[ 1.0000000] sio0 at pci0 dev 7 function 0: vendor 1080 product c693 (rev. 0x00)
[ 1.0000000] cypide0 at pci0 dev 7 function 1: Cypress 82C693 IDE Controller (rev. 0x00)
[ 1.0000000] cypide0: primary channel wired to compatibility mode
[ 1.0000000] cypide0: primary channel interrupting at isa irq 14
[ 1.0000000] atabus0 at cypide0 channel 0
[ 1.0000000] cypide1 at pci0 dev 7 function 2: Cypress 82C693 IDE Controller (rev. 0x00)
[ 1.0000000] cypide1: hardware does not support DMA
[ 1.0000000] cypide1: primary channel wired to compatibility mode
[ 1.0000000] cypide1: secondary channel interrupting at isa irq 15
[ 1.0000000] atabus1 at cypide1 channel 0
[ 1.0000000] vendor 1080 product c693 (USB serial bus, OHCI) at pci0 dev 7 function 3 not configured
[ 1.0000000] mpt0 at pci0 dev 11 function 0: vendor 1000 product 0030 (rev. 0x08)
[ 1.0000000] mpt0: interrupting at dec 6600 irq 40
[ 1.0000000] scsibus0 at mpt0: 16 targets, 8 luns per target
[ 1.0000000] mpt1 at pci0 dev 11 function 1: vendor 1000 product 0030 (rev. 0x08)
[ 1.0000000] mpt1: interrupting at dec 6600 irq 41
[ 1.0000000] scsibus1 at mpt1: 16 targets, 8 luns per target
[ 1.0000000] vga0 at pci0 dev 12 function 0: vendor 1002 product 5157 (rev. 0x00)
[ 1.0000000] wsdisplay0 at vga0 (kbdmux ignored)
[ 1.0000000] drm at vga0 not configured
[ 1.0000000] wm0 at pci0 dev 13 function 0: Intel i82544EI 1000BASE-T Ethernet (rev. 0x02)
[ 1.0000000] wm0: interrupting at dec 6600 irq 32
[ 1.0000000] wm0: Ethernet address 00:02:b3:d0:61:b9
[ 1.0000000] makphy0 at wm0 phy 1: Marvell 88E1000 Gigabit PHY, rev. 0
[ 1.0000000] makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[ 1.0000000] isa0 at sio0
[ 1.0000000] com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, 16-byte FIFO
[ 1.0000000] com0: console
[ 1.0000000] com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 16-byte FIFO
[ 1.0000000] lpt0 at isa0 port 0x3bc-0x3bf irq 7
[ 1.0000000] pckbc0 at isa0 port 0x60-0x64
[ 1.0000000] pckbd0 at pckbc0 (kbd slot)
[ 1.0000000] pckbc0: using irq 1 for kbd slot
[ 1.0000000] wskbd0 at pckbd0 (mux ignored)
[ 1.0000000] pms0 at pckbc0 (aux slot)
[ 1.0000000] pckbc0: using irq 12 for aux slot
[ 1.0000000] wsmouse0 at pms0 (mux ignored)
[ 1.0000000] fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
[ 1.0000000] mcclock0 at isa0 port 0x70-0x71: mc146818 compatible time-of-day clock
[ 1.0000000] tsp1 at tsc0
[ 1.0000000] pci1 at tsp1 bus 0
[ 1.0000000] tlp0 at pci1 dev 3 function 0: DECchip 21143 Ethernet, pass 4.1
[ 1.0000000] tlp0: interrupting at dec 6600 irq 45
[ 1.0000000] tlp0: DEC, Ethernet address 08:00:2b:87:1d:b2
[ 1.0000000] tlp0: 10baseT, 10base2, 10base5, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[ 1.0000000] isp0 at pci1 dev 6 function 0: QLogic 1020 Fast Wide SCSI HBA
[ 1.0000000] isp0: interrupting at dec 6600 irq 47
[ 1.0000000] ppb0 at pci1 dev 8 function 0: vendor 1011 product 0024 (rev. 0x03)
[ 1.0000000] pci2 at ppb0 bus 2
[ 1.0000000] vendor 1106 product 3038 (USB serial bus, UHCI, revision 0x61) at pci2 dev 9 function 0 not configured
[ 1.0000000] vendor 1106 product 3038 (USB serial bus, UHCI, revision 0x61) at pci2 dev 9 function 1 not configured
[ 1.0000000] vendor 1106 product 3104 (USB serial bus, EHCI, revision 0x62) at pci2 dev 9 function 2 not configured
[ 1.0000000] vendor 1106 product 3044 (IEEE1394 serial bus, OpenHCI, revision 0x46) at pci2 dev 9 function 3 not configured
[ 1.0000000] tsciic at tsc0
[ 1.0000000] not configured
[ 1.0000000] WARNING: system needs entropy for security; see entropy(7)
[ 1.1360136] scsibus0: waiting 2 seconds for devices to settle...
[ 1.2058331] scsibus1: waiting 2 seconds for devices to settle...
[ 1.2776171] scsibus2 at isp0: 16 targets, 8 luns per target
[ 1.3489067] stray isa irq 14
[ 1.3821142] scsibus2: waiting 2 seconds for devices to settle...
[ 1.4535961] atapibus0 at atabus0: 2 targets
[ 1.5035184] stray isa irq 14
[ 1.5520380] cd0 at atapibus0 drive 0: <MATSHITADVD-RAM SW-9585, , B100> cdrom removable
[ 3.6204537] sd0 at scsibus0 target 0 lun 0: <COMPAQ, BF0369B272, HPB9> disk fixed
[ 3.7102998] sd0: 34732 MB, 36070 cyl, 2 head, 986 sec, 512 bytes/sect x 71132000 sectors
[ 3.8079587] sd0: sync (6.25ns offset 127), 16-bit (320.000MB/s) transfers, tagged queueing
[ 4.1370692] fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
[ 18.9685423] sd1 at scsibus2 target 1 lun 0: <QUANTUM, ATLAS 10K 9WLS, UCHK> disk fixed
[ 19.0622960] sd1: 8683 MB, 10042 cyl, 6 head, 295 sec, 512 bytes/sect x 17783240 sectors
[ 19.1580011] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 25.7695153] WARNING: can't figure what device matches "IDE 0 107 0 0 0 0 0"
[ 25.8517396] root on md0a dumps on md0b
[ 25.8964712] root file system type: ffs
[ 25.9411866] kern.module.path=/stand/alpha/11.99.5/modules
Terminal type? [vt100] [ 26.1220649] entropy: best effort
Erase set to backspace.
erase ^?, werase ^W, kill ^U, intr ^C
2-2)John's patched 11.0_RC1 image
>>>boot dqa0 -fl A
(boot dqa0.0.0.107.0 -flags A)
block 0 of dqa0.0.0.107.0 is a valid boot block
reading 13 blocks from dqa0.0.0.107.0
bootstrap code read in
base = 1b2000, image_start = 0, image_bytes = 1a00
initializing HWRPB at 2000
initializing page table at 7ffee000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
NetBSD/alpha 11.0_RC1 ISO 9660 Primary Bootstrap
Jumping to entry point...
NetBSD/alpha 11.0_RC1 Secondary Bootstrap, Revision 1.13 (Tue Feb 17 02:52:46 UTC 2026)
VMS PAL rev: 0x1001b00010158
OSF PAL rev: 0x1001600020153
Switch to OSF PAL code succeeded.
Boot flags: A
11290976+255344=0xb034d0
Entering netbsd at 0xfffffc0000a01410...
[ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[ 1.0000000] 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[ 1.0000000] 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[ 1.0000000] 2024, 2025, 2026
[ 1.0000000] The NetBSD Foundation, Inc. All rights reserved.
[ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.0000000] The Regents of the University of California. All rights reserved.
[ 1.0000000] NetBSD 11.0_RC1 (INSTALL) #0: Tue Feb 17 02:57:57 UTC 2026
[ 1.0000000] john%platypus.zia.io@localhost:/usr/obj-alpha/sys/arch/alpha/compile/INSTALL
[ 1.0000000] COMPAQ Professional Workstation XP1000, 666MHz, s/n AY0
[ 1.0000000] 8192 byte page size, 1 processor.
[ 1.0000000] total memory = 2048 MB
[ 1.0000000] (1816 KB reserved for PROM, 2046 MB used by NetBSD)
[ 1.0000000] avail memory = 2006 MB
[ 1.0000000] mainbus0 (root)
[ 1.0000000] cpu0 at mainbus0: ID 0 (primary), 21264A-8 (EV67)
[ 1.0000000] cpu0: Architecture extensions: 0x307<PAT,MVI,CIX,FIX,BWX>
[ 1.0000000] tsc0 at mainbus0: 21272 Core Logic Chipset, Cchip rev 0
[ 1.0000000] tsc0: 4 Dchips, 1 memory bus of 32 bytes
[ 1.0000000] tsc0: arrays present: 1024MB, 1024MB (split), 0MB, 0MB, Dchip 0 rev 1
[ 1.0000000] tsp0 at tsc0
[ 1.0000000] pci0 at tsp0 bus 0
[ 1.0000000] sio0 at pci0 dev 7 function 0: vendor 1080 product c693 (rev. 0x00)
[ 1.0000000] cypide0 at pci0 dev 7 function 1: Cypress 82C693 IDE Controller (rev. 0x00)
[ 1.0000000] cypide0: primary channel wired to compatibility mode
[ 1.0000000] cypide0: primary channel interrupting at isa irq 14
[ 1.0000000] atabus0 at cypide0 channel 0
[ 1.0000000] cypide1 at pci0 dev 7 function 2: Cypress 82C693 IDE Controller (rev. 0x00)
[ 1.0000000] cypide1: hardware does not support DMA
[ 1.0000000] cypide1: primary channel wired to compatibility mode
[ 1.0000000] cypide1: secondary channel interrupting at isa irq 15
[ 1.0000000] atabus1 at cypide1 channel 0
[ 1.0000000] vendor 1080 product c693 (USB serial bus, OHCI) at pci0 dev 7 function 3 not configured
[ 1.0000000] mpt0 at pci0 dev 11 function 0: vendor 1000 product 0030 (rev. 0x08)
[ 1.0000000] mpt0: interrupting at dec 6600 irq 40
[ 1.0000000] scsibus0 at mpt0: 16 targets, 8 luns per target
[ 1.0000000] mpt1 at pci0 dev 11 function 1: vendor 1000 product 0030 (rev. 0x08)
[ 1.0000000] mpt1: interrupting at dec 6600 irq 41
[ 1.0000000] scsibus1 at mpt1: 16 targets, 8 luns per target
[ 1.0000000] vga0 at pci0 dev 12 function 0: vendor 1002 product 5157 (rev. 0x00)
[ 1.0000000] wsdisplay0 at vga0 (kbdmux ignored)
[ 1.0000000] drm at vga0 not configured
[ 1.0000000] wm0 at pci0 dev 13 function 0: Intel i82544EI 1000BASE-T Ethernet (rev. 0x02)
[ 1.0000000] wm0: interrupting at dec 6600 irq 32
[ 1.0000000] wm0: Ethernet address 00:02:b3:d0:61:b9
[ 1.0000000] makphy0 at wm0 phy 1: Marvell 88E1000 Gigabit PHY, rev. 0
[ 1.0000000] makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[ 1.0000000] isa0 at sio0
[ 1.0000000] lpt0 at isa0 port 0x3bc-0x3bf irq 7
[ 1.0000000] com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, 16-byte FIFO
[ 1.0000000] com0: console
[ 1.0000000] com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 16-byte FIFO
[ 1.0000000] pckbc0 at isa0 port 0x60-0x64
[ 1.0000000] pckbd0 at pckbc0 (kbd slot)
[ 1.0000000] pckbc0: using irq 1 for kbd slot
[ 1.0000000] wskbd0 at pckbd0 (mux ignored)
[ 1.0000000] pms0 at pckbc0 (aux slot)
[ 1.0000000] pckbc0: using irq 12 for aux slot
[ 1.0000000] wsmouse0 at pms0 (mux ignored)
[ 1.0000000] fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
[ 1.0000000] mcclock0 at isa0 port 0x70-0x71: mc146818 compatible time-of-day clock
[ 1.0000000] tsp1 at tsc0
[ 1.0000000] pci1 at tsp1 bus 0
[ 1.0000000] tlp0 at pci1 dev 3 function 0: DECchip 21143 Ethernet, pass 4.1
[ 1.0000000] tlp0: interrupting at dec 6600 irq 45
[ 1.0000000] tlp0: DEC, Ethernet address 08:00:2b:87:1d:b2
[ 1.0000000] tlp0: 10baseT, 10base2, 10base5, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[ 1.0000000] isp0 at pci1 dev 6 function 0: QLogic 1020 Fast Wide SCSI HBA
[ 1.0000000] isp0: interrupting at dec 6600 irq 47
[ 1.0000000] ppb0 at pci1 dev 8 function 0: vendor 1011 product 0024 (rev. 0x03)
[ 1.0000000] pci2 at ppb0 bus 2
[ 1.0000000] vendor 1106 product 3038 (USB serial bus, UHCI, revision 0x61) at pci2 dev 9 function 0 not configured
[ 1.0000000] vendor 1106 product 3038 (USB serial bus, UHCI, revision 0x61) at pci2 dev 9 function 1 not configured
[ 1.0000000] vendor 1106 product 3104 (USB serial bus, EHCI, revision 0x62) at pci2 dev 9 function 2 not configured
[ 1.0000000] vendor 1106 product 3044 (IEEE1394 serial bus, OpenHCI, revision 0x46) at pci2 dev 9 function 3 not configured
[ 1.0000000] tsciic at tsc0
[ 1.0000000] not configured
[ 1.0000000] WARNING: system needs entropy for security; see entropy(7)
[ 1.1350024] scsibus0: waiting 2 seconds for devices to settle...
[ 1.2054330] scsibus1: waiting 2 seconds for devices to settle...
[ 1.2775836] scsibus2 at isp0: 16 targets, 8 luns per target
[ 1.3488701] stray isa irq 14
[ 1.3814261] scsibus2: waiting 2 seconds for devices to settle...
[ 1.4531872] atapibus0 at atabus0: 2 targets
[ 1.5031705] stray isa irq 14
[ 1.5519967] cd0 at atapibus0 drive 0: <MATSHITADVD-RAM SW-9585, , B100> cdrom removable
[ 3.6203437] sd0 at scsibus0 target 0 lun 0: <COMPAQ, BF0369B272, HPB9> disk fixed
[ 3.7101873] sd0: 34732 MB, 36070 cyl, 2 head, 986 sec, 512 bytes/sect x 71132000 sectors
[ 3.8078422] sd0: sync (6.25ns offset 127), 16-bit (320.000MB/s) transfers, tagged queueing
[ 4.1369421] fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
[ 18.9679356] sd1 at scsibus2 target 1 lun 0: <QUANTUM, ATLAS 10K 9WLS, UCHK> disk fixed
[ 19.0616852] sd1: 8683 MB, 10042 cyl, 6 head, 295 sec, 512 bytes/sect x 17783240 sectors
[ 19.1573883] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 25.7686892] WARNING: can't figure what device matches "IDE 0 107 0 0 0 0 0"
[ 25.8507186] root on md0a dumps on md0b
[ 25.8956422] root file system type: ffs
[ 25.9401134] kern.module.path=/stand/alpha/11.0/modules
Terminal type? [vt100] [ 26.1290390] entropy: best effort
Erase set to backspace.
erase ^?, werase ^W, kill ^U, intr ^C
2-3)Thorpej's patched image
>>>boot dqa0 -fl A
(boot dqa0.0.0.107.0 -flags A)
block 0 of dqa0.0.0.107.0 is a valid boot block
reading 13 blocks from dqa0.0.0.107.0
bootstrap code read in
base = 1b2000, image_start = 0, image_bytes = 1a00
initializing HWRPB at 2000
initializing page table at 7ffee000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
NetBSD/alpha 11.99.5 ISO 9660 Primary Bootstrap
Jumping to entry point...
NetBSD/alpha 11.99.5 Secondary Bootstrap, Revision 1.13 (Wed Apr 22 03:25:12 UTC 2026)
VMS PAL rev: 0x1001b00010158
OSF PAL rev: 0x1001600020153
Switch to OSF PAL code succeeded.
Boot flags: A
11314192+254592=0xb08d40
Entering netbsd at 0xfffffc0000a01410...
[ 1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[ 1.0000000] 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[ 1.0000000] 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[ 1.0000000] 2024, 2025, 2026
[ 1.0000000] The NetBSD Foundation, Inc. All rights reserved.
[ 1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.0000000] The Regents of the University of California. All rights reserved.
[ 1.0000000] NetBSD 11.99.5 (INSTALL) #1: Wed Apr 22 04:27:07 PDT 2026
[ 1.0000000] thorpej@the-ripe-vessel:/nbsd/objdir/alpha/sys/arch/alpha/compile/INSTALL
[ 1.0000000] COMPAQ Professional Workstation XP1000, 666MHz, s/n AY0
[ 1.0000000] 8192 byte page size, 1 processor.
[ 1.0000000] total memory = 2048 MB
[ 1.0000000] (1816 KB reserved for PROM, 2046 MB used by NetBSD)
[ 1.0000000] avail memory = 2006 MB
[ 1.0000000] mainbus0 (root)
[ 1.0000000] cpu0 at mainbus0: ID 0 (primary), 21264A-8 (EV67)
[ 1.0000000] cpu0: Architecture extensions: 0x307<PAT,MVI,CIX,FIX,BWX>
[ 1.0000000] tsc0 at mainbus0: 21272 Core Logic Chipset, Cchip rev 0
[ 1.0000000] tsc0: 4 Dchips, 1 memory bus of 32 bytes
[ 1.0000000] tsc0: arrays present: 1024MB, 1024MB (split), 0MB, 0MB, Dchip 0 rev 1
[ 1.0000000] tsp0 at tsc0
[ 1.0000000] pci0 at tsp0 bus 0
[ 1.0000000] sio0 at pci0 dev 7 function 0: vendor 1080 product c693 (rev. 0x00)
[ 1.0000000] cypide0 at pci0 dev 7 function 1: Cypress 82C693 IDE Controller (rev. 0x00)
[ 1.0000000] cypide0: primary channel wired to compatibility mode
[ 1.0000000] cypide0: primary channel interrupting at isa irq 14
[ 1.0000000] atabus0 at cypide0 channel 0
[ 1.0000000] cypide1 at pci0 dev 7 function 2: Cypress 82C693 IDE Controller (rev. 0x00)
[ 1.0000000] cypide1: hardware does not support DMA
[ 1.0000000] cypide1: primary channel wired to compatibility mode
[ 1.0000000] cypide1: secondary channel interrupting at isa irq 15
[ 1.0000000] atabus1 at cypide1 channel 0
[ 1.0000000] vendor 1080 product c693 (USB serial bus, OHCI) at pci0 dev 7 function 3 not configured
[ 1.0000000] mpt0 at pci0 dev 11 function 0: vendor 1000 product 0030 (rev. 0x08)
[ 1.0000000] mpt0: interrupting at dec 6600 irq 40
[ 1.0000000] scsibus0 at mpt0: 16 targets, 8 luns per target
[ 1.0000000] mpt1 at pci0 dev 11 function 1: vendor 1000 product 0030 (rev. 0x08)
[ 1.0000000] mpt1: interrupting at dec 6600 irq 41
[ 1.0000000] scsibus1 at mpt1: 16 targets, 8 luns per target
[ 1.0000000] vga0 at pci0 dev 12 function 0: vendor 1002 product 5157 (rev. 0x00)
[ 1.0000000] wsdisplay0 at vga0 (kbdmux ignored)
[ 1.0000000] drm at vga0 not configured
[ 1.0000000] wm0 at pci0 dev 13 function 0: Intel i82544EI 1000BASE-T Ethernet (rev. 0x02)
[ 1.0000000] wm0: interrupting at dec 6600 irq 32
[ 1.0000000] wm0: Ethernet address 00:02:b3:d0:61:b9
[ 1.0000000] makphy0 at wm0 phy 1: Marvell 88E1000 Gigabit PHY, rev. 0
[ 1.0000000] makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[ 1.0000000] isa0 at sio0
[ 1.0000000] com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, 16-byte FIFO
[ 1.0000000] com0: console
[ 1.0000000] com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 16-byte FIFO
[ 1.0000000] lpt0 at isa0 port 0x3bc-0x3bf irq 7
[ 1.0000000] pckbc0 at isa0 port 0x60-0x64
[ 1.0000000] pckbd0 at pckbc0 (kbd slot)
[ 1.0000000] pckbc0: using irq 1 for kbd slot
[ 1.0000000] wskbd0 at pckbd0 (mux ignored)
[ 1.0000000] pms0 at pckbc0 (aux slot)
[ 1.0000000] pckbc0: using irq 12 for aux slot
[ 1.0000000] wsmouse0 at pms0 (mux ignored)
[ 1.0000000] fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
[ 1.0000000] mcclock0 at isa0 port 0x70-0x71: mc146818 compatible time-of-day clock
[ 1.0000000] tsp1 at tsc0
[ 1.0000000] pci1 at tsp1 bus 0
[ 1.0000000] tlp0 at pci1 dev 3 function 0: DECchip 21143 Ethernet, pass 4.1
[ 1.0000000] tlp0: interrupting at dec 6600 irq 45
[ 1.0000000] tlp0: DEC, Ethernet address 08:00:2b:87:1d:b2
[ 1.0000000] tlp0: 10baseT, 10base2, 10base5, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[ 1.0000000] isp0 at pci1 dev 6 function 0: QLogic 1020 Fast Wide SCSI HBA
[ 1.0000000] isp0: interrupting at dec 6600 irq 47
[ 1.0000000] ppb0 at pci1 dev 8 function 0: vendor 1011 product 0024 (rev. 0x03)
[ 1.0000000] pci2 at ppb0 bus 2
[ 1.0000000] vendor 1106 product 3038 (USB serial bus, UHCI, revision 0x61) at pci2 dev 9 function 0 not configured
[ 1.0000000] vendor 1106 product 3038 (USB serial bus, UHCI, revision 0x61) at pci2 dev 9 function 1 not configured
[ 1.0000000] vendor 1106 product 3104 (USB serial bus, EHCI, revision 0x62) at pci2 dev 9 function 2 not configured
[ 1.0000000] vendor 1106 product 3044 (IEEE1394 serial bus, OpenHCI, revision 0x46) at pci2 dev 9 function 3 not configured
[ 1.0000000] tsciic at tsc0
[ 1.0000000] not configured
[ 1.0000000] WARNING: system needs entropy for security; see entropy(7)
[ 1.1359970] scsibus0: waiting 2 seconds for devices to settle...
[ 1.2063132] scsibus1: waiting 2 seconds for devices to settle...
[ 1.2785805] scsibus2 at isp0: 16 targets, 8 luns per target
[ 1.3498679] stray isa irq 14
[ 1.3822839] scsibus2: waiting 2 seconds for devices to settle...
[ 1.4540472] atapibus0 at atabus0: 2 targets
[ 1.5039676] stray isa irq 14
[ 1.5529963] cd0 at atapibus0 drive 0: <MATSHITADVD-RAM SW-9585, , B100> cdrom removable
[ 3.6203810] sd0 at scsibus0 target 0 lun 0: <COMPAQ, BF0369B272, HPB9> disk fixed
[ 3.7092470] sd0: 34732 MB, 36070 cyl, 2 head, 986 sec, 512 bytes/sect x 71132000 sectors
[ 3.8069033] sd0: sync (6.25ns offset 127), 16-bit (320.000MB/s) transfers, tagged queueing
[ 4.1360053] fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
[ 18.9671086] sd1 at scsibus2 target 1 lun 0: <QUANTUM, ATLAS 10K 9WLS, UCHK> disk fixed
[ 19.0608588] sd1: 8683 MB, 10042 cyl, 6 head, 295 sec, 512 bytes/sect x 17783240 sectors
[ 19.1565621] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers, tagged queueing
[ 25.7679118] WARNING: can't figure what device matches "IDE 0 107 0 0 0 0 0"
[ 25.8499432] root on md0a dumps on md0b
[ 25.8948673] root file system type: ffs
[ 25.9393455] kern.module.path=/stand/alpha/11.99.5/modules
Terminal type? [vt100] [ 26.1282647] entropy: best effort
Erase set to backspace.
erase ^?, werase ^W, kill ^U, intr ^C
--
Yoshihiko Iwama
Home |
Main Index |
Thread Index |
Old Index