Hi, Robert Elz wrote: > Date: Wed, 13 Nov 2013 10:23:11 +0100 > From: Riccardo Mottola <riccardo.mottola%libero.it@localhost> > Message-ID: <528344FF.4090603%libero.it@localhost> > > | Life without X11 is boring :) The only thing which I could still try is > | to leave the network card in, but remove/rename the ifconfig.xx0 file. > > I doubt that will make a difference - it sounds as if you have a hardware > resource conflict of some kind. It was worth the try: no difference, that confirms the suspicion of some kind of conflict between X and my network card. > > Post a dmesg for this system from soon after it has booted (the content > of /var/run/dmesg.boot should be fine) - there's no need to attempt starting > X for this, just want to see what interrupts, etc, have been assigned > for your network and display adaptor. Attached. I just logged in remotely, copied the file and used another machine to send email :) > > If you have (or can) install sysutils/acpidump, run that, and include its > output as well. Installed, acpidump -dt attached. R
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.1.2 (GENERIC)
total memory = 191 MB
avail memory = 175 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Generic PC
mainbus0 (root)
cpu0 at mainbus0: Intel 586-class, 232MHz, id 0x581
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <IBM ,TP600 ,00000001>, AslId < ,00000000>
LNKD: ACPI: Found matching pin for 0.1.INTD at func 2: 11
LNKA: ACPI: Found matching pin for 0.2.INTA at func 0: 255
LNKB: ACPI: Found matching pin for 0.2.INTB at func 1: 255
LNKA: ACPI: Found matching pin for 0.3.INTA at func 0: 11
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
acpiec0 at acpi0 (EC0, PNP0C09): io 0x62,0x66
acpilid0 at acpi0 (LID0, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
FDC0 (PNP0700) at acpi0 not configured
LPT (PNP0400) at acpi0 not configured
FIR (IBM0071) at acpi0 not configured
CS10 (CSC0010) at acpi0 not configured
CS00 (CSC0000) at acpi0 not configured
joy0 at acpi0 (CS01, CSC0001): io 0x200-0x207
joy0: joystick not connected
attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
MBRD (PNP0C02) at acpi0 not configured
npx1 at acpi0 (MPRC, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
pckbc1 at acpi0 (KBD0, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (MOU0, IBM3780) (aux port): irq 12
acpibat0 at acpi0 (BAT0, PNP0C0A-0): ACPI Battery
acpiacad0 at acpi0 (AC, ACPI0003-0): ACPI AC Adapter
acpifan0 at acpi0 (FAN0, PNP0C0B-0): ACPI Fan
acpifan1 at acpi0 (FAN1, PNP0C0B-1): ACPI Fan
acpitz0 at acpi0 (THM0)
acpitz0: active cooling level 0: 65.0C
acpitz0: active cooling level 1: 62.0C
acpitz0: levels: critical 68.0 C, passive 57.0 C
acpitz1 at acpi0 (THM2)
acpitz1: active cooling level 0: 66.0C
acpitz1: active cooling level 1: 63.0C
acpitz1: levels: critical 69.0 C
acpitz2 at acpi0 (THM6)
acpitz2: active cooling level 0: 60.0C
acpitz2: active cooling level 1: 57.0C
acpitz2: levels: critical 63.0 C
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x7100 (rev. 0x01)
pcib0 at pci0 dev 1 function 0: vendor 0x8086 product 0x7110 (rev. 0x01)
piixide0 at pci0 dev 1 function 1: Intel 82371AB IDE controller (PIIX4) (rev.
0x01)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
uhci0 at pci0 dev 1 function 2: vendor 0x8086 product 0x7112 (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
piixpm0 at pci0 dev 1 function 3: vendor 0x8086 product 0x7113 (rev. 0x01)
timecounter: Timecounter "piixpm0" frequency 3579545 Hz quality 900
piixpm0: 24-bit timer
piixpm0: interrupting at SMI, polling
iic0 at piixpm0: I2C bus
cbb0 at pci0 dev 2 function 0: vendor 0x104c product 0xac16 (rev. 0x02)
cbb1 at pci0 dev 2 function 1: vendor 0x104c product 0xac16 (rev. 0x02)
vga1 at pci0 dev 3 function 0: vendor 0x10c8 product 0x0004 (rev. 0x01)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
isa0 at pcib0
lpt2 at isa0 port 0x3bc-0x3bf irq : polled
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
sb0 at isa0 port 0x220-0x237 irq 5 drq 1: dsp v3.02
audio0 at sb0: half duplex, playback, capture, mmap, independent
midi1 at sb0: SB MIDI UART
opl0 at sb0: model OPL3
midi2 at opl0: SB Yamaha OPL3
isapnp0 at isa0 port 0x279
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
cbb0: cacheline 0x8 lattimer 0xa8
cbb0: bhlc 0x82a808
cbb0: interrupting at irq 11
cardslot0 at cbb0
cardbus0 at cardslot0: bus 1
pcmcia0 at cardslot0
cbb1: cacheline 0x8 lattimer 0xa8
cbb1: bhlc 0x82a808
cbb1: interrupting at irq 11
cardslot1 at cbb1
cardbus1 at cardslot1: bus 4
pcmcia1 at cardslot1
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 232121080 Hz quality 3000
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
acpiacad0: AC adapter online.
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
tlp0 at cardbus1 function 0: Xircom X3201-3 Ethernet, pass 0.3
tlp0: Ethernet address 00:10:a4:9f:1c:21
tqphy0 at tlp0 phy 0: 78Q2120 10/100 media interface, rev. 11
tqphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
wd0 at atabus0 drive 0
wd0: <IBM-DJSA-210>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 5729 MB, 12416 cyl, 15 head, 63 sec, 512 bytes/sect x 11733120 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <TOSHIBA CD-ROM XM-1702BC, , 1562> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2
cd0(piixide0:1:0): using PIO mode 4, DMA mode 2 (using DMA)
Kernelized RAIDframe activated
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
Attachment:
acpidump.Z
Description: Binary data