NetBSD on Compaq Armada 1530D laptop

["Ari Constancio" <ari.constancio%gmail.com@localhost>]

Hello,

I'm starting to use NetBSD and decided to try it on a Compaq Armada
1530D laptop (fairly old - came with Windows 95).

I have an external Cardbus(?) network card (Conceptronic CSP100TCL)
but it seems not to be working, even though it appears below on
dmesg(8).

Here's the output from dmesg(8):

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0 (GENERIC) #0: Sun Dec 16 00:20:10 PST 2007
        
builds@wb34:/home/builds/ab/netbsd-4-0-RELEASE/i386/200712160005Z-obj/home/builds/ab/netbsd-4-0-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 15996 KB
rbus: rbus_min_start set to 0x20000000
avail memory = 5532 KB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xf7000
mainbus0 (root)
ACPI Error (tbxfroot-0775): No valid RSDP was found [20060217]
ACPI Exception (tbxfroot-0531): AE_NOT_FOUND, RSDP structure not found
- Flags=8 [20060217]
ACPI Exception (tbxface-0162): AE_NO_ACPI_TABLES, Could not get the
RSDP [20060217]
ACPI Exception (tbxface-0211): AE_NO_ACPI_TABLES, Could not load
tables [20060217]
ACPI: unable to load tables: AE_NO_ACPI_TABLES
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium/MMX (586-class), 131.21 MHz, id 0x543
cpu0: features 8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
cpu0: features 8001bf<MMX>
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Opti 82C701 (rev. 0x20)
pcib0 at pci0 dev 1 function 0
pcib0: Opti 82C700 (rev. 0x20)
vga1 at pci0 dev 2 function 0: Cirrus Logic CL-GD7548 (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
cbb0 at pci0 dev 17 function 0: Texas Instruments PCI1131 PCI-CardBus
Bridge (rev. 0x01)
cbb1 at pci0 dev 17 function 1: Texas Instruments PCI1131 PCI-CardBus
Bridge (rev. 0x01)
optiide0 at pci0 dev 20 function 0
optiide0: OPTi 82d568 (82c621 compatible) PCI IDE controller (rev. 0x12)
optiide0: bus-master DMA support present but disabled due to chip rev. <= 0x12
optiide0: primary channel wired to compatibility mode
optiide0: primary channel interrupting at irq 14
atabus0 at optiide0 channel 0
optiide0: secondary channel wired to compatibility mode
optiide0: secondary channel ignored (disabled)
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com2 at isa0 port 0x3e8-0x3ef irq 5: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
sb0 at isa0 port 0x220-0x237 irq 5 drq 1: dsp v3.01
audio0 at sb0: half duplex, mmap, independent
midi0 at sb0: SB MIDI UART (CPU-intensive output)
opl0 at sb0: model OPL3
midi1 at opl0: SB Yamaha OPL3 (CPU-intensive output)
pcppi0 at isa0 port 0x61
pcppi0: children must have an explicit unit
midi2 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
pcppi0: attached to attimer0
isapnp0: no ISA Plug 'n Play devices found
cbb0: interrupting at irq 15
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1
pcmcia0 at cardslot0
cbb1: interrupting at irq 11
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 2
pcmcia1 at cardslot1
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
Conceptronic, 100TCL CardBus 10/100 Ethernet (manufacturer 0x0,
product 0x21b) Realtek Semiconductor 8139 10/100 Ethernet (ethernet
network, revision 0x10) at cardbus0 function 0 not configured
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <UJDA120, , 1.01> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 1
wd0 at atabus0 drive 0: <ST91420AG>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 1375 MB, 2794 cyl, 16 head, 63 sec, 512 bytes/sect x 2816352 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2
wd0(optiide0:0:0): using PIO mode 4
cd0(optiide0:0:1): using PIO mode 4
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)

I appreciate any pointers on solving this (recompiling the kernel, etc.).

Thanks in advance,
Ari Constâncio