Re: port-sgimips/57654

To: port-sgimips-maintainer%netbsd.org@localhost,gnats-admin%netbsd.org@localhost,netbsd-bugs%netbsd.org@localhost,iwama%t3.rim.or.jp@localhost
Subject: Re: port-sgimips/57654
From: <iwama%t3.rim.or.jp@localhost>
Date: Wed, 7 Aug 2024 20:55:01 +0000 (UTC)
The following reply was made to PR port-sgimips/57654; it has been noted by GNATS.

From: <iwama%t3.rim.or.jp@localhost>
To: <gnats-bugs%NetBSD.org@localhost>
Cc: 
Subject: Re: port-sgimips/57654
Date: Thu, 8 Aug 2024 05:49:56 +0900

 Additionally I tried the O2 R5000SC 180MHz with similar results to the O2
 R5000SC 200MHz and the Indy R5000SC 150MHz.
 That is, O2 boots from the 9.0 installation CD, but not from 9.1.
 Note that after a failed boot on 9.1 or later, the LED will turn amber.
 
 > hinv
                    System: IP32
                 Processor: 180 Mhz R5000, with FPU
      Primary I-cache size: 32 Kbytes
      Primary D-cache size: 32 Kbytes
      Secondary cache size: 512 Kbytes
               Memory size: 256 Mbytes
                  Graphics: CRM, Rev C
                     Audio: A3 version 1
                 SCSI Disk: scsi(0)disk(1)
                 SCSI Disk: scsi(0)disk(2)
                SCSI CDROM: scsi(0)cdrom(4)
 > version
 
 
 PROM Monitor (BE)
 Tue Oct 22 10:58:00 PDT 2002 
 VERSION 4.18
 O2 R5K/R7K/R10K/R12K
 IRIX 6.5.x IP32prom IP32PROM-v4
 
 > boot -f scsi(0)disk(1)rdisk(0)partition(8)sash
 scsi(0)disk(1)rdisk(0)partition(0)NetBSD/9.1/netbsd-INSTALL32_IP3x
 136992+22896+3248+341792+49584d+4620+6880 entry: 0x8ffa5e50
 11845456+131856 entry: 0x80069000
 [   1.0000000] phys segment: 0x5e000 @ 0x2000
 [   1.0000000] adding 0x5e000 @ 0x2000 to freelist 0
 [   1.0000000] phys segment: 0xb6c000 @ 0x60000
 [   1.0000000] adding 0x6000 @ 0x60000 to freelist 0
 [   1.0000000] skipping 0xb66000 @ 0x66000 (kernel)
 [   1.0000000] phys segment: 0x182000 @ 0xbce000
 [   1.0000000] adding 0x182000 @ 0xbce000 to freelist 0
 [   1.0000000] phys segment: 0xeb84000 @ 0x1400000
 [   1.0000000] adding 0xeb84000 @ 0x1400000 to freelist 0
 [   1.0000000] phys segment: 0x7c000 @ 0xff84000
 [   1.0000000] adding 0x7c000 @ 0xff84000 to freelist 0
 (freezed here)
 
 > boot -f scsi(0)disk(1)rdisk(0)partition(8)sash
 scsi(0)disk(1)rdisk(0)partition(0)NetBSD/9.0/netbsd-INSTALL32_IP3x
 136992+22896+3248+341792+49584d+4620+6880 entry: 0x8ffa5e50
 11815376+131840 entry: 0x80069000
 [   1.0000000] phys segment: 0x5e000 @ 0x2000
 [   1.0000000] adding 0x5e000 @ 0x2000 to freelist 0
 [   1.0000000] phys segment: 0xb64000 @ 0x60000
 [   1.0000000] adding 0x6000 @ 0x60000 to freelist 0
 [   1.0000000] skipping 0xb5e000 @ 0x66000 (kernel)
 [   1.0000000] phys segment: 0x18a000 @ 0xbc6000
 [   1.0000000] adding 0x18a000 @ 0xbc6000 to freelist 0
 [   1.0000000] phys segment: 0xeb84000 @ 0x1400000
 [   1.0000000] adding 0xeb84000 @ 0x1400000 to freelist 0
 [   1.0000000] phys segment: 0x7c000 @ 0xff84000
 [   1.0000000] adding 0x7c000 @ 0xff84000 to freelist 0
 [   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
 2004, 2005,
 [   1.0000000]     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014,
 2015, 2016, 2017,
 [   1.0000000]     2018, 2019, 2020 The NetBSD Foundation, Inc.  All rights
 reserved.
 [   1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
 [   1.0000000]     The Regents of the University of California.  All rights
 reserved.
 
 [   1.0000000] NetBSD 9.0 (INSTALL32_IP3x) #0: Fri Feb 14 00:06:28 UTC 2020
 [   1.0000000]
 mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/sgimips/compile/INSTALL32_IP3x
 [   1.0000000] total memory = 255 MB
 [   1.0000000] (6848 KB reserved for ARCS)
 [   1.0000000] avail memory = 235 MB
 [   1.0000000] mainbus0 (root): SGI-IP32 [SGI, 0], 1 processor
 [   1.0000000] cpu0 at mainbus0: MIPS R5000 CPU (0x2321) Rev. 2.1 with
 built-in FPU Rev. 1.0
 [   1.0000000] cpu0: 48 TLB entries, 16MB max page size
 [   1.0000000] cpu0: 32KB/32B 2-way set-associative L1 instruction cache
 [   1.0000000] cpu0: 32KB/32B 2-way set-associative write-back L1 data cache
 [   1.0000000] cpu0: 512KB/32B direct-mapped write-through L2 unified cache
 [   1.0000000] crime0 at mainbus0 addr 0x14000000: rev 1.1 (CRIME_ID: 161)
 [   1.0000000] crmfb0 at mainbus0 addr 0x16000000: SGI CRIME Graphics
 Display Engine
 [   1.0000000] crmfb0: device unusable if not setup by firmware
 [   1.0000000] mace0 at mainbus0 addr 0x1f000000
 [   1.0000000] lpt0 at mace0 offset 0x380000 intr 4 intrmask 0xf0000
 [   1.0000000] com0 at mace0 offset 0x390000 intr 4 intrmask 0x3f00000:
 ns16550a, working fifo
 [   1.0000000] com0: console
 [   1.0000000] com1 at mace0 offset 0x398000 intr 4 intrmask 0xfc000000:
 ns16550a, working fifo
 [   1.0000000] macekbc0 at mace0 offset 0x320000 intr 5 intrmask 0x0: PS2
 controller
 [   1.0000000] mcclock0 at mace0 offset 0x3a0000 intrmask 0x0
 [   1.0000000] mec0 at mace0 offset 0x280000 intr 3 intrmask 0x0: MAC-110
 Ethernet, rev 1
 [   1.0000000] mec0: Ethernet address 08:00:69:05:a4:60
 [   1.0000000] nsphy0 at mec0 phy 31: DP83840 10/100 media interface, rev. 1
 [   1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
 100baseT4, auto
 [   1.0000000] mavb0 at mace0 offset 0x300000 intr 6 intrmask 0x0: AD1843
 rev 1
 [   1.0000000] audio0 at mavb0: playback
 [   1.0000000] audio0: slinear_be:16 -> slinear_be:24 2ch 48000Hz, blk 40ms
 for playback
 [   1.0000000] spkr0 at audio0: PC Speaker (synthesized)
 [   1.0000000] wsbell at spkr0 not configured
 [   1.0000000] macepci0 at mace0 offset 0x80000 intr 7 intrmask 0x0: rev 1
 [   1.0000000] pci0 at macepci0 bus 0
 [   1.0000000] ahc0 at pci0 dev 1 function 0: Adaptec aic7880 Ultra SCSI
 adapter
 [   1.0000000] ahc0: interrupting at crime interrupt 8
 [   1.0000000] ahc0: Using left over BIOS settings
 [   1.0000000] ahc0: Host Adapter has no SEEPROM. Using default SCSI target
 parameters
 [   1.0000000] ahc0: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
 [   1.0000000] scsibus0 at ahc0: 16 targets, 8 luns per target
 [   1.0000000] ahc1 at pci0 dev 2 function 0: Adaptec aic7880 Ultra SCSI
 adapter
 [   1.0000000] ahc1: interrupting at crime interrupt 9
 [   1.0000000] ahc1: Using left over BIOS settings
 [   1.0000000] ahc1: Host Adapter has no SEEPROM. Using default SCSI target
 parameters
 [   1.0000000] ahc1: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
 [   1.0000000] scsibus1 at ahc1: 16 targets, 8 luns per target
 [   1.0000030] scsibus0: waiting 2 seconds for devices to settle...
 [   1.0718872] scsibus1: waiting 2 seconds for devices to settle...
 [   3.1341342] sd0 at scsibus0 target 1 lun 0: <FUJITSU, MAN3184MC, 0108>
 disk fixed
 [   3.2255886] sd0: 17366 MB, 30050 cyl, 2 head, 591 sec, 512 bytes/sect x
 35566483 sectors
 [   3.3238294] sd0: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
 tagged queueing
 [   3.4236492] sd1 at scsibus0 target 2 lun 0: <SEAGATE, ST373307LC, 0007>
 disk fixed
 [   3.5154881] sd1: 70007 MB, 49855 cyl, 4 head, 718 sec, 512 bytes/sect x
 143374744 sectors
 [   3.6150877] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
 tagged queueing
 [   3.9859588] cd0 at scsibus0 target 4 lun 0: <TOSHIBA, CD-ROM XM-5401TA,
 3605> cdrom removable
 [   4.0986991] cd0: sync (236.00ns offset 15), 8-bit (4.237MB/s) transfers
 [  11.0327623] WARNING: 1 error while detecting hardware; check system log.
 [  11.1135330] boot device: sd0
 [  11.1580962] root on md0a dumps on md0b
 [  11.2032820] root file system type: ffs
 [  11.2514663] kern.module.path=/stand/sgimips/9.0/modules
 Created mfs /dev (282624 byte, 480 inodes)
 -sh: tset: not found
 erase ^?, werase ^W, kill ^U, intr ^C
 
 Also, after replacing the 3 files modified in PR#55139 with the 9.0 ones, O2
 boots even from the 9.1 installation CD.
 
 > boot -f scsi(0)disk(1)rdisk(0)partition(8)sash
 scsi(0)disk(1)rdisk(0)partition(0)NetBSD/9.1-r5k/netbsd-INSTALL32_IP3x
 136992+22896+3248+341792+49584d+4620+6880 entry: 0x8ffa5e50
 11845872+131824 entry: 0x80069000
 [   1.0000000] phys segment: 0x5e000 @ 0x2000
 [   1.0000000] adding 0x5e000 @ 0x2000 to freelist 0
 [   1.0000000] phys segment: 0xb6c000 @ 0x60000
 [   1.0000000] adding 0x6000 @ 0x60000 to freelist 0
 [   1.0000000] skipping 0xb66000 @ 0x66000 (kernel)
 [   1.0000000] phys segment: 0x182000 @ 0xbce000
 [   1.0000000] adding 0x182000 @ 0xbce000 to freelist 0
 [   1.0000000] phys segment: 0xeb84000 @ 0x1400000
 [   1.0000000] adding 0xeb84000 @ 0x1400000 to freelist 0
 [   1.0000000] phys segment: 0x7c000 @ 0xff84000
 [   1.0000000] adding 0x7c000 @ 0xff84000 to freelist 0
 [   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
 2004, 2005,
 [   1.0000000]     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014,
 2015, 2016, 2017,
 [   1.0000000]     2018, 2019, 2020 The NetBSD Foundation, Inc.  All rights
 reserved.
 [   1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
 [   1.0000000]     The Regents of the University of California.  All rights
 reserved.
 
 [   1.0000000] NetBSD 9.1 (INSTALL32_IP3x) #0: Thu Oct 12 02:55:22 JST 2023
 [   1.0000000]
 iwama%netbsd-v.led.t3.rim.or.jp@localhost:/home/iwama/NetBSD-9.1-sgimips-indy/usr/obj/
 sys/arch/sgimips/compile/INSTALL32_IP3x
 [   1.0000000] total memory = 255 MB
 [   1.0000000] (6848 KB reserved for ARCS)
 [   1.0000000] avail memory = 235 MB
 [   1.0000000] mainbus0 (root): SGI-IP32 [SGI, 0], 1 processor
 [   1.0000000] cpu0 at mainbus0: MIPS R5000 CPU (0x2321) Rev. 2.1 with
 built-in FPU Rev. 1.0
 [   1.0000000] cpu0: 48 TLB entries, 16MB max page size
 [   1.0000000] cpu0: 32KB/32B 2-way set-associative L1 instruction cache
 [   1.0000000] cpu0: 32KB/32B 2-way set-associative write-back L1 data cache
 [   1.0000000] cpu0: 512KB/32B direct-mapped write-through L2 unified cache
 [   1.0000000] crime0 at mainbus0 addr 0x14000000: rev 1.1 (CRIME_ID: 161)
 [   1.0000000] crmfb0 at mainbus0 addr 0x16000000: SGI CRIME Graphics
 Display Engine
 [   1.0000000] crmfb0: device unusable if not setup by firmware
 [   1.0000000] mace0 at mainbus0 addr 0x1f000000
 [   1.0000000] lpt0 at mace0 offset 0x380000 intr 4 intrmask 0xf0000
 [   1.0000000] com0 at mace0 offset 0x390000 intr 4 intrmask 0x3f00000:
 ns16550a, working fifo
 [   1.0000000] com0: console
 [   1.0000000] com1 at mace0 offset 0x398000 intr 4 intrmask 0xfc000000:
 ns16550a, working fifo
 [   1.0000000] macekbc0 at mace0 offset 0x320000 intr 5 intrmask 0x0: PS2
 controller
 [   1.0000000] mcclock0 at mace0 offset 0x3a0000 intrmask 0x0
 [   1.0000000] mec0 at mace0 offset 0x280000 intr 3 intrmask 0x0: MAC-110
 Ethernet, rev 1
 [   1.0000000] mec0: Ethernet address 08:00:69:05:a4:60
 [   1.0000000] nsphy0 at mec0 phy 31: DP83840 10/100 media interface, rev. 1
 [   1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
 100baseT4, auto
 [   1.0000000] mavb0 at mace0 offset 0x300000 intr 6 intrmask 0x0: AD1843
 rev 1
 [   1.0000000] audio0 at mavb0: playback
 [   1.0000000] audio0: slinear_be:16 -> slinear_be:24 2ch 48000Hz, blk 3840
 bytes (10ms) for playback
 [   1.0000000] spkr0 at audio0: PC Speaker (synthesized)
 [   1.0000000] wsbell at spkr0 not configured
 [   1.0000000] macepci0 at mace0 offset 0x80000 intr 7 intrmask 0x0: rev 1
 [   1.0000000] pci0 at macepci0 bus 0
 [   1.0000000] ahc0 at pci0 dev 1 function 0: Adaptec aic7880 Ultra SCSI
 adapter
 [   1.0000000] ahc0: interrupting at crime interrupt 8
 [   1.0000000] ahc0: Using left over BIOS settings
 [   1.0000000] ahc0: Host Adapter has no SEEPROM. Using default SCSI target
 parameters
 [   1.0000000] ahc0: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
 [   1.0000000] scsibus0 at ahc0: 16 targets, 8 luns per target
 [   1.0000000] ahc1 at pci0 dev 2 function 0: Adaptec aic7880 Ultra SCSI
 adapter
 [   1.0000000] ahc1: interrupting at crime interrupt 9
 [   1.0000000] ahc1: Using left over BIOS settings
 [   1.0000000] ahc1: Host Adapter has no SEEPROM. Using default SCSI target
 parameters
 [   1.0000000] ahc1: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
 [   1.0000000] scsibus1 at ahc1: 16 targets, 8 luns per target
 [   1.0000030] scsibus0: waiting 2 seconds for devices to settle...
 [   1.0718763] scsibus1: waiting 2 seconds for devices to settle...
 [   3.1341192] sd0 at scsibus0 target 1 lun 0: <FUJITSU, MAN3184MC, 0108>
 disk fixed
 [   3.2258829] sd0: 17366 MB, 30050 cyl, 2 head, 591 sec, 512 bytes/sect x
 35566483 sectors
 [   3.3242277] sd0: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
 tagged queueing
 [   3.4240459] sd1 at scsibus0 target 2 lun 0: <SEAGATE, ST373307LC, 0007>
 disk fixed
 [   3.5158872] sd1: 70007 MB, 49855 cyl, 4 head, 718 sec, 512 bytes/sect x
 143374744 sectors
 [   3.6154874] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
 tagged queueing
 [   3.9862513] cd0 at scsibus0 target 4 lun 0: <TOSHIBA, CD-ROM XM-5401TA,
 3605> cdrom removable
 [   4.0999308] cd0: sync (236.00ns offset 15), 8-bit (4.237MB/s) transfers
 [  11.0338882] WARNING: 1 error while detecting hardware; check system log.
 [  11.1148593] boot device: sd0
 [  11.1594195] root on md0a dumps on md0b
 [  11.2079572] root file system type: ffs
 [  11.2561496] kern.module.path=/stand/sgimips/9.1/modules
 [  11.3189794] WARNING: clock lost 10145 days
 [  11.3682037] WARNING: using filesystem time
 [  11.4174354] WARNING: CHECK AND RESET THE DATE!
 Created mfs /dev (282624 byte, 480 inodes)
 -sh: tset: not found
 erase ^?, werase ^W, kill ^U, intr ^C
Prev by Date: NetBSD Nightly Trouble Ticket Report
Next by Date: lib/58562: libedit should register signal handlers with SA_ONSTACK flag
Previous by Thread: Re: port-sgimips/57654
Next by Thread: install/58392: sysinst upgrade to 10.99.11 fails
Indexes:
Home | Main Index | Thread Index | Old Index