Re: port-sgimips/57654

To: port-sgimips-maintainer%netbsd.org@localhost,gnats-admin%netbsd.org@localhost,netbsd-bugs%netbsd.org@localhost,iwama%t3.rim.or.jp@localhost
Subject: Re: port-sgimips/57654
From: <iwama%t3.rim.or.jp@localhost>
Date: Wed, 3 Jul 2024 04:10:02 +0000 (UTC)
The following reply was made to PR port-sgimips/57654; it has been noted by GNATS.

From: <iwama%t3.rim.or.jp@localhost>
To: <gnats-bugs%NetBSD.org@localhost>
Cc: 
Subject: Re: port-sgimips/57654
Date: Wed, 3 Jul 2024 13:07:10 +0900

 I tried it on O2 with R5000SC 200MHz, with similar results as Indy R5000SC
 150MHz.
 That is, O2 boots from the 9.0 installation CD, but not from 9.1.
 Note that after a failed boot on 9.1 or later, the LED will turn amber.
 
 > hinv
                    System: IP32
                 Processor: 200 Mhz R5000, with FPU
      Primary I-cache size: 32 Kbytes
      Primary D-cache size: 32 Kbytes
      Secondary cache size: 1024 Kbytes
               Memory size: 256 Mbytes
                  Graphics: CRM, Rev C
                     Audio: A3 version 1
                 SCSI Disk: scsi(0)disk(1)
                 SCSI Disk: scsi(0)disk(2)
                SCSI CDROM: scsi(0)cdrom(4)
 > version
 
 
 PROM Monitor (BE)
 Tue Oct 22 10:58:00 PDT 2002 
 VERSION 4.18
 O2 R5K/R7K/R10K/R12K
 IRIX 6.5.x IP32prom IP32PROM-v4
 
 > boot -f scsi(0)disk(1)rdisk(0)partition(8)sash
 scsi(0)disk(1)rdisk(0)partition(0)NetBSD/9.1/netbsd-INSTALL32_IP3x
 136992+22896+3248+341792+49584d+4620+6880 entry: 0x8ffa5e50
 11845456+131856 entry: 0x80069000
 [   1.0000000] phys segment: 0x5e000 @ 0x2000
 [   1.0000000] adding 0x5e000 @ 0x2000 to freelist 0
 [   1.0000000] phys segment: 0xb6c000 @ 0x60000
 [   1.0000000] adding 0x6000 @ 0x60000 to freelist 0
 [   1.0000000] skipping 0xb66000 @ 0x66000 (kernel)
 [   1.0000000] phys segment: 0x182000 @ 0xbce000
 [   1.0000000] adding 0x182000 @ 0xbce000 to freelist 0
 [   1.0000000] phys segment: 0xeb84000 @ 0x1400000
 [   1.0000000] adding 0xeb84000 @ 0x1400000 to freelist 0
 [   1.0000000] phys segment: 0x7c000 @ 0xff84000
 [   1.0000000] adding 0x7c000 @ 0xff84000 to freelist 0
 (freezed here)
 
 
 > boot -f scsi(0)disk(1)rdisk(0)partition(8)sash
 scsi(0)disk(1)rdisk(0)partition(0)NetBSD/9.0/netbsd-INSTALL32_IP3x
 136992+22896+3248+341792+49584d+4620+6880 entry: 0x8ffa5e50
 11815376+131840 entry: 0x80069000
 [   1.0000000] phys segment: 0x5e000 @ 0x2000
 [   1.0000000] adding 0x5e000 @ 0x2000 to freelist 0
 [   1.0000000] phys segment: 0xb64000 @ 0x60000
 [   1.0000000] adding 0x6000 @ 0x60000 to freelist 0
 [   1.0000000] skipping 0xb5e000 @ 0x66000 (kernel)
 [   1.0000000] phys segment: 0x18a000 @ 0xbc6000
 [   1.0000000] adding 0x18a000 @ 0xbc6000 to freelist 0
 [   1.0000000] phys segment: 0xeb84000 @ 0x1400000
 [   1.0000000] adding 0xeb84000 @ 0x1400000 to freelist 0
 [   1.0000000] phys segment: 0x7c000 @ 0xff84000
 [   1.0000000] adding 0x7c000 @ 0xff84000 to freelist 0
 [   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
 2004, 2005,
 [   1.0000000]     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014,
 2015, 2016, 2017,
 [   1.0000000]     2018, 2019, 2020 The NetBSD Foundation, Inc.  All rights
 reserved.
 [   1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
 [   1.0000000]     The Regents of the University of California.  All rights
 reserved.
 
 [   1.0000000] NetBSD 9.0 (INSTALL32_IP3x) #0: Fri Feb 14 00:06:28 UTC 2020
 [   1.0000000]
 mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/sgimips/compile/INSTALL32_IP3x
 [   1.0000000] total memory = 255 MB
 [   1.0000000] (6848 KB reserved for ARCS)
 [   1.0000000] avail memory = 235 MB
 [   1.0000000] mainbus0 (root): SGI-IP32 [SGI, 0], 1 processor
 [   1.0000000] cpu0 at mainbus0: MIPS R5000 CPU (0x2321) Rev. 2.1 with
 built-in FPU Rev. 1.0
 [   1.0000000] cpu0: 48 TLB entries, 16MB max page size
 [   1.0000000] cpu0: 32KB/32B 2-way set-associative L1 instruction cache
 [   1.0000000] cpu0: 32KB/32B 2-way set-associative write-back L1 data cache
 [   1.0000000] cpu0: 1024KB/32B direct-mapped write-through L2 unified cache
 [   1.0000000] crime0 at mainbus0 addr 0x14000000: rev 1.1 (CRIME_ID: 161)
 [   1.0000000] crmfb0 at mainbus0 addr 0x16000000: SGI CRIME Graphics
 Display Engine
 [   1.0000000] crmfb0: device unusable if not setup by firmware
 [   1.0000000] mace0 at mainbus0 addr 0x1f000000
 [   1.0000000] lpt0 at mace0 offset 0x380000 intr 4 intrmask 0xf0000
 [   1.0000000] com0 at mace0 offset 0x390000 intr 4 intrmask 0x3f00000:
 ns16550a, working fifo
 [   1.0000000] com0: console
 [   1.0000000] com1 at mace0 offset 0x398000 intr 4 intrmask 0xfc000000:
 ns16550a, working fifo
 [   1.0000000] macekbc0 at mace0 offset 0x320000 intr 5 intrmask 0x0: PS2
 controller
 [   1.0000000] mcclock0 at mace0 offset 0x3a0000 intrmask 0x0
 [   1.0000000] mec0 at mace0 offset 0x280000 intr 3 intrmask 0x0: MAC-110
 Ethernet, rev 1
 [   1.0000000] mec0: Ethernet address 08:00:69:05:a4:60
 [   1.0000000] nsphy0 at mec0 phy 31: DP83840 10/100 media interface, rev. 1
 [   1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
 100baseT4, auto
 [   1.0000000] mavb0 at mace0 offset 0x300000 intr 6 intrmask 0x0: AD1843
 rev 1
 [   1.0000000] audio0 at mavb0: playback
 [   1.0000000] audio0: slinear_be:16 -> slinear_be:24 2ch 48000Hz, blk 40ms
 for playback
 [   1.0000000] spkr0 at audio0: PC Speaker (synthesized)
 [   1.0000000] wsbell at spkr0 not configured
 [   1.0000000] macepci0 at mace0 offset 0x80000 intr 7 intrmask 0x0: rev 1
 [   1.0000000] pci0 at macepci0 bus 0
 [   1.0000000] ahc0 at pci0 dev 1 function 0: Adaptec aic7880 Ultra SCSI
 adapter
 [   1.0000000] ahc0: interrupting at crime interrupt 8
 [   1.0000000] ahc0: Using left over BIOS settings
 [   1.0000000] ahc0: Host Adapter has no SEEPROM. Using default SCSI target
 parameters
 [   1.0000000] ahc0: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
 [   1.0000000] scsibus0 at ahc0: 16 targets, 8 luns per target
 [   1.0000000] ahc1 at pci0 dev 2 function 0: Adaptec aic7880 Ultra SCSI
 adapter
 [   1.0000000] ahc1: interrupting at crime interrupt 9
 [   1.0000000] ahc1: Using left over BIOS settings
 [   1.0000000] ahc1: Host Adapter has no SEEPROM. Using default SCSI target
 parameters
 [   1.0000000] ahc1: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
 [   1.0000000] scsibus1 at ahc1: 16 targets, 8 luns per target
 [   1.0000030] scsibus0: waiting 2 seconds for devices to settle...
 [   1.0716421] scsibus1: waiting 2 seconds for devices to settle...
 [   3.1338890] sd0 at scsibus0 target 1 lun 0: <FUJITSU, MAN3184MC, 0108>
 disk fixed
 [   3.2252320] sd0: 17366 MB, 30050 cyl, 2 head, 591 sec, 512 bytes/sect x
 35566483 sectors
 [   3.3233646] sd0: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
 tagged queueing
 [   3.4230806] sd1 at scsibus0 target 2 lun 0: <MAXTOR, ATLAS10K5_73SCA,
 JS03> disk fixed
 [   3.5177480] sd1: 69809 MB, 81782 cyl, 2 head, 874 sec, 512 bytes/sect x
 142969680 sectors
 [   3.6180813] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
 tagged queueing
 [   3.9888445] cd0 at scsibus0 target 4 lun 0: <TOSHIBA, CD-ROM XM-5401TA,
 3605> cdrom removable
 [   4.1016871] cd0: sync (236.00ns offset 15), 8-bit (4.237MB/s) transfers
 [  11.0357456] WARNING: 1 error while detecting hardware; check system log.
 [  11.1164956] boot device: sd0
 [  11.1610577] root on md0a dumps on md0b
 [  11.2086529] root file system type: ffs
 [  11.2568358] kern.module.path=/stand/sgimips/9.0/modules
 [  11.3196714] WARNING: clock lost 8809 days
 [  11.3678488] WARNING: using filesystem time
 [  11.4170792] WARNING: CHECK AND RESET THE DATE!
 Created mfs /dev (282624 byte, 480 inodes)
 -sh: tset: not found
 erase ^?, werase ^W, kill ^U, intr ^C
 
 Also, after replacing the 3 files modified in PR#55139 with the 9.0 ones, O2
 boots even from the 9.1 installation CD.
 
 > boot -f scsi(0)cdrom(4)partition(8)ip3xboot
 54464+1792 entry: 0x80002000
 
 NetBSD/sgimips 9.1 Bootstrap, Revision 1.5 (Wed Oct 11 17:23:46 UTC 2023)
 
 devopen: scsi(0)cdrom(4)partition(0) type scsi file ip3x
 11845872+131824=0xb6c878
 [   1.0000000] phys segment: 0xe000 @ 0x2000
 [   1.0000000] adding 0xe000 @ 0x2000 to freelist 0
 [   1.0000000] phys segment: 0xd40000 @ 0x10000
 [   1.0000000] adding 0x56000 @ 0x10000 to freelist 0
 [   1.0000000] adding 0x182000 @ 0xbce000 to freelist 0
 [   1.0000000] phys segment: 0xec00000 @ 0x1400000
 [   1.0000000] adding 0xec00000 @ 0x1400000 to freelist 0
 [   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
 2004, 2005,
 [   1.0000000]     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014,
 2015, 2016, 2017,
 [   1.0000000]     2018, 2019, 2020 The NetBSD Foundation, Inc.  All rights
 reserved.
 [   1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
 [   1.0000000]     The Regents of the University of California.  All rights
 reserved.
 
 [   1.0000000] NetBSD 9.1 (INSTALL32_IP3x) #0: Thu Oct 12 02:55:22 JST 2023
 [   1.0000000]
 iwama%netbsd-v.led.t3.rim.or.jp@localhost:/home/iwama/NetBSD-9.1-sgimips-indy/usr/obj/
 sys/arch/sgimips/compile/INSTALL32_IP3x
 [   1.0000000] total memory = 255 MB
 [   1.0000000] (6848 KB reserved for ARCS)
 [   1.0000000] avail memory = 235 MB
 [   1.0000000] mainbus0 (root): SGI-IP32 [SGI, 0], 1 processor
 [   1.0000000] cpu0 at mainbus0: MIPS R5000 CPU (0x2321) Rev. 2.1 with
 built-in FPU Rev. 1.0
 [   1.0000000] cpu0: 48 TLB entries, 16MB max page size
 [   1.0000000] cpu0: 32KB/32B 2-way set-associative L1 instruction cache
 [   1.0000000] cpu0: 32KB/32B 2-way set-associative write-back L1 data cache
 [   1.0000000] cpu0: 1024KB/32B direct-mapped write-through L2 unified cache
 [   1.0000000] crime0 at mainbus0 addr 0x14000000: rev 1.1 (CRIME_ID: 161)
 [   1.0000000] crmfb0 at mainbus0 addr 0x16000000: SGI CRIME Graphics
 Display Engine
 [   1.0000000] crmfb0: device unusable if not setup by firmware
 [   1.0000000] mace0 at mainbus0 addr 0x1f000000
 [   1.0000000] lpt0 at mace0 offset 0x380000 intr 4 intrmask 0xf0000
 [   1.0000000] com0 at mace0 offset 0x390000 intr 4 intrmask 0x3f00000:
 ns16550a, working fifo
 [   1.0000000] com0: console
 [   1.0000000] com1 at mace0 offset 0x398000 intr 4 intrmask 0xfc000000:
 ns16550a, working fifo
 [   1.0000000] macekbc0 at mace0 offset 0x320000 intr 5 intrmask 0x0: PS2
 controller
 [   1.0000000] mcclock0 at mace0 offset 0x3a0000 intrmask 0x0
 [   1.0000000] mec0 at mace0 offset 0x280000 intr 3 intrmask 0x0: MAC-110
 Ethernet, rev 1
 [   1.0000000] mec0: Ethernet address 08:00:69:05:a4:60
 [   1.0000000] nsphy0 at mec0 phy 31: DP83840 10/100 media interface, rev. 1
 [   1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
 100baseT4, auto
 [   1.0000000] mavb0 at mace0 offset 0x300000 intr 6 intrmask 0x0: AD1843
 rev 1
 [   1.0000000] audio0 at mavb0: playback
 [   1.0000000] audio0: slinear_be:16 -> slinear_be:24 2ch 48000Hz, blk 3840
 bytes (10ms) for playback
 [   1.0000000] spkr0 at audio0: PC Speaker (synthesized)
 [   1.0000000] wsbell at spkr0 not configured
 [   1.0000000] macepci0 at mace0 offset 0x80000 intr 7 intrmask 0x0: rev 1
 [   1.0000000] pci0 at macepci0 bus 0
 [   1.0000000] ahc0 at pci0 dev 1 function 0: Adaptec aic7880 Ultra SCSI
 adapter
 [   1.0000000] ahc0: interrupting at crime interrupt 8
 [   1.0000000] ahc0: Using left over BIOS settings
 [   1.0000000] ahc0: Host Adapter has no SEEPROM. Using default SCSI target
 parameters
 [   1.0000000] ahc0: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
 [   1.0000000] scsibus0 at ahc0: 16 targets, 8 luns per target
 [   1.0000000] ahc1 at pci0 dev 2 function 0: Adaptec aic7880 Ultra SCSI
 adapter
 [   1.0000000] ahc1: interrupting at crime interrupt 9
 [   1.0000000] ahc1: Using left over BIOS settings
 [   1.0000000] ahc1: Host Adapter has no SEEPROM. Using default SCSI target
 parameters
 [   1.0000000] ahc1: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
 [   1.0000000] scsibus1 at ahc1: 16 targets, 8 luns per target
 [   1.0000030] scsibus0: waiting 2 seconds for devices to settle...
 [   1.0716207] scsibus1: waiting 2 seconds for devices to settle...
 [   3.1338656] sd0 at scsibus0 target 1 lun 0: <FUJITSU, MAN3184MC, 0108>
 disk fixed
 [   3.2250875] sd0: 17366 MB, 30050 cyl, 2 head, 591 sec, 512 bytes/sect x
 35566483 sectors
 [   3.3233260] sd0: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
 tagged queueing
 [   3.4230386] sd1 at scsibus0 target 2 lun 0: <MAXTOR, ATLAS10K5_73SCA,
 JS03> disk fixed
 [   3.5177076] sd1: 69809 MB, 81782 cyl, 2 head, 874 sec, 512 bytes/sect x
 142969680 sectors
 [   3.6180393] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
 tagged queueing
 [   3.9886950] cd0 at scsibus0 target 4 lun 0: <TOSHIBA, CD-ROM XM-5401TA,
 3605> cdrom removable
 [   4.1015337] cd0: sync (236.00ns offset 15), 8-bit (4.237MB/s) transfers
 [  16.0253745] WARNING: 1 error while detecting hardware; check system log.
 [  16.1071668] boot device: <unknown>
 [  16.1480027] root on md0a dumps on md0b
 [  16.1898947] root file system type: ffs
 [  16.2380823] kern.module.path=/stand/sgimips/9.1/modules
 [  16.3009134] WARNING: clock lost 10145 days
 [  16.3501358] WARNING: using filesystem time
 [  16.3993676] WARNING: CHECK AND RESET THE DATE!
 Created mfs /dev (282624 byte, 480 inodes)
 -sh: tset: not found
 erase ^?, werase ^W, kill ^U, intr ^C
Prev by Date: Re: kern/58382 (url(4): kernel panic after ifconfig url0 up on NetBSD 10.0)
Next by Date: install/58392: sysinst upgrade to 10.99.11 fails
Previous by Thread: lib/58391: re-adding syslog_ss() to syslog.h and syslog.3
Next by Thread: Re: port-sgimips/57654
Indexes:
Home | Main Index | Thread Index | Old Index