NetBSD-Bugs archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: kern/57564 test after the commit
Hello
El 7/8/23 a las 21:55, Ramiro Aceves escribió:
The following reply was made to PR port-evbarm/57564; it has been noted by GNATS.
From: Ramiro Aceves <ea1abz%gmail.com@localhost>
To: gnats-bugs%netbsd.org@localhost, port-evbarm-maintainer%netbsd.org@localhost,
gnats-admin%netbsd.org@localhost, netbsd-bugs%netbsd.org@localhost
Cc:
Subject: Re: kern/57564
Date: Mon, 7 Aug 2023 21:50:07 +0200
Hello,
I have followed the great NetBSD Guide and crosscompiled a kernel from
my Debian GNU/Linux machine:
raspa-netbsd$ uname -a
NetBSD raspa-netbsd 10.99.7 NetBSD 10.99.7 (MYKERNEL) #0: Mon Aug 7
21:31:38 CEST 2023
ramiro@debian-nuc8i7:/home/ramiro/cvs/src/sys/arch/evbarm/compile/MYKERNEL
evbarm
I am going to run the CVS torture and see what happens.
Ramiro.
The last crash left a different message on dmesg:
panic: kernel diagnostic assertion "l == (l1 = curlwp)" failed: file
"../../../../sys/lwp.h",
line 544 l=0x0 curlwp=0x9bcf3b80
Here the complete messages in /var/run/dmesg.boot:
of California. All rights reserved.
NetBSD 10.99.7 (MYKERNEL) #0: Mon Aug 7 21:31:38 CEST 2023
ramiro@debian-nuc8i7:/home/ramiro/cvs/src/sys/arch/evbarm/compile/MYKERNEL
total memory = 448 MB
avail memory = 428 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
armfdt0 (roB enabled LABT
cpu0: L1 16KB/32B 4-way (128 set) VIPT Instruction cache
cpu0: L1 16KB/32B 4-way (128 set) write-back-locking-C VIPT Data cache
vfp0 at cpu0: VFP11, rounding, exceptions
fclock0 at simplebus2: 19200000 Hz fixed clock (osc)
fclock1 at simplebus2: 480000000 Hz fixed clock (otg)
bcmicu0 at simplebus1
bcmcprman0 at simplebus1: BCM283x Clock Controller
bcmtmr0 at simplebus1: VC System Timer
bcmtmr0: interrupting on icu irq 3
bcmaux0 at simplebus1
/soc/thermal@7e212000 at simplebus1 not configured
bcmgpio0 at simplebus1: GPIO controller 2835
bcmgpio0: pins 0..31 interrupting on icu irq 49
bcmgpio0: pins 32..54 interrupting on icu irq 50
gpio0 at bcmgpio0: 54 pins
bcmdmac0 at simplebus1: DMA0 DMA2 DMA4 DMA5 DMA8 DMA9 DMA10 DMA11
/soc/power at simplebus1 not configured
/wifi-pwrseq at simplebus0 not configured
/phy at simplebus0 not configured
bsciic0 at simplebus1: Broadcom Serial Controller
bsciic0: interrupting on icu irq 53
iic0 at bsciic0: I2C bus
bcmmbox0 at simplebus1: VC mailbox
bcmmbox0: interrupting on icu irq 65
vcmbox0 at bcmmbox0
/soc/firmware at simplebus1 not configured
/soc/txp@7e004000 at simplebus1 not configured
plcom0 at simplebus1: ARM PL011 UART
plcom0: txfifo 16 bytes
plcom0: interrupting on icu irq 57
bcmsdhost0 at simplebus1: SD HOST controller
bcmsdhost0: interrupting on icu irq 56
bsciic1 at simplebus1: Broadcom Serial Controller
bsciic1: interrupting on icu irq 53
iic1 at bsciic1: I2C bus
com0 at simplebus1: BCM AUX UART, 1-byte FIFO
com0: console
com0: interrupting on icu irq 29
sdhc0 at simplebus1: SDHC controller
sdhc0: interrupting on icu irq 62
bsciic2 at simplebus1: Broadcom Serial Controller
bsciic2: interrupting on icu irq 53
iic2 at bsciic2: I2C bus
dwctwo0 at simplebus1: USB controller
dwctwo0: interrupting on icu irq 9
bcmpmwdog0 at simplebus1: Power management, Reset and Watchdog controller
/soc/vec@7e806000 at simplebus1 not configured
/soc/hdmi@7e902000 at simplebus1 not configured
/soc/gpu at simplebus1 not configured
genfb0 at simplebus1: switching to framebuffer console
genfb0: framebuffer at 0x5e876000, size 1280x720, depth 32, stride 5120
wsdisplay0 at genfb0 kbdmux 1: console (default, vt100 emulation)
wsmux1: connecting to wsdisplay0
wsdisplay0: screen 1-3 added (default, vt100 emulation)
vchiq0 at simplebus1: BCM2835 VCHIQ
/arm-pmu at simplebus0 not configured
gpioleds0 at simplebus0: ACT
bcmrng0 at simplebus1: RNG
entropy: ready
timecounter: Timecounter "bcmtmr0" frequency 1000000 Hz quality 100
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
sdmmc0 at bcmsdhost0
sdhc0: SDHC 3.0, rev 153, caps <01610000/00000000>, platform DMA, 200000
kHz, HS 3.3V, re-tuning mode 1, 1024 byte blocks
sdmmc1 at sdhc0 slot 0
dwctwo0: Core Release: 2.80a (snpsid=4f54280a)
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0: NetBSD (0x0000) DWC2 root hub (0x0000), class 9/0, rev
2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
IPsec: Initialized Security Association Processing.
sdmmc0: direct I/O error 5, r=6 p=0xc96edf14 write
sdmmc0: SD card status: 4-bit, C10
ld0 at sdmmc0: <0x03:0x5344:SL16G:0x80:0xed7b3c40:0x113>
ld0: 15193 MB, 7717 cyl, 64 head, 63 sec, 512 bytes/sect x 31116288 sectors
ld0: 4-bit width, High-Speed/SDR25, 50.000 MHz
sdmmc1: 4-bit width, 50.000 MHz
bwfm0 at sdmmc1 function 1
(manufacturer 0x2d0, product 0xa9a6) at sdmmc1 function 2 not configured
bwfm1 at uhub0 port 1: Broadcom (0x0a5c) BCMUSB 802.11 Wireless Adapter
(0xbd1e), rev 2.00/0.01, addr 2
uhub0: autoconfiguration error: illegal enable change, port 1
swwdog0: software watchdog initialized
WARNING: 1 error while detecting hardware; check system log.
boot device: ld0
root on ld0a dumps on ld0b
root file system type: ffs
kern.module.path=/stand/evbarm/10.99.7/modules
vchiq0: interrupting on icu irq 66
vchiq: vchiq_init_state: slot_zero = 0xc9b30000, is_master = 0
vchiq: local ver 8 (min 3), remote ver 8.
vcaudio0 at vchiq0: auds
notice: vchiq_get_state: g_state.remote->initialised != 1 (0)
bwfm0: Firmware file default: brcmfmac43430-sdio.bin
bwfm0: Firmware file model-spec:
brcmfmac43430-sdio.raspberrypi,model-zero-w.bin
WARNING: no TOD clock present
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
audio0 at vcaudio0: playback
audio0: slinear_le:16 -> slinear_le:16 2ch 48000Hz, blk 7680 bytes
(40ms) for playback
spkr0 at audio0: PC Speaker (synthesized)
wsbell at spkr0 not configured
bwfm1: address a0:64:8f:55:f6:9c
bwfm1: wl0: Apr 3 2014 04:43:32 version 6.10.198.66 (r467479) FWID
01-32bd010e
bwfm0: Found Firmware file: brcmfmac43430-sdio.bin
bwfm0: NVRAM file default: brcmfmac43430-sdio.txt
bwfm0: NVRAM file model-spec:
brcmfmac43430-sdio.raspberrypi,model-zero-w.txt
bwfm0: Found NVRAM file: brcmfmac43430-sdio.raspberrypi,model-zero-w.txt
bwfm0: CLM file default: brcmfmac43430-sdio.clm_blob
bwfm0: CLM file model-spec:
brcmfmac43430-sdio.raspberrypi,model-zero-w.clm_blob
bwfm0: CHIPACTIVE
bwfm0: address b8:27:eb:5b:ff:03
bwfm0: wl0: Oct 23 2017 03:55:53 version 7.45.98.38 (r674442 CY) FWID
01-e58d219f
wsdisplay0: screen 4 added (default, vt100 emulation)
panic: kernel diagnostic assertion "l == (l1 = curlwp)" failed: file
"../../../../sys/lwp.h", line 544 l=0x0 curlwp=0x9bcf3b80
cpu0: Begin traceback...
0xc9c41af4: netbsd:db_panic+0xc
0xc9c41b14: netbsd:vpanic+0xf4
0xc9c41b2c: netbsd:kern_assert+0x3c
0xc9c41b84: netbsd:cache_lookup+0x7c0
0xc9c41c34: netbsd:ufs_lookup+0xcc
0xc9c41c6c: netbsd:VOP_LOOKUP+0x48
0xc9c41cc4: netbsd:lookup_once+0x1b8
0xc9c41d8c: netbsd:namei_tryemulroot+0x984
0xc9c41dc4: netbsd:namei+0x34
0xc9c41e34: netbsd:do_sys_statat+0xf0
0xc9c41eec: netbsd:sys___stat50+0x2c
0xc9c41fac: netbsd:syscall+0x188
cpu0: End traceback...
dump to dev 92,1 not possible
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 10.99.7 (MYKERNEL) #0: Mon Aug 7 21:31:38 CEST 2023
ramiro@debian-nuc8i7:/home/ramiro/cvs/src/sys/arch/evbarm/compile/MYKERNEL
total memory = 448 MB
avail memory = 428 MB
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
armfdt0 (root)
simplebus0 at armfdt0: Raspberry Pi Zero W Rev 1.1
simplebus1 at simplebus0
simplebus2 at simplebus0
simplebus3 at simplebus0
cpus0 at simplebus0
cpu0 at cpus0: 700 MHz ARM1176JZ-S r0p7 (ARM11J V6ZK core)
cpu0: DC enabled IC enabled WB enabled LABT
cpu0: L1 16KB/32B 4-way (128 set) VIPT Instruction cache
cpu0: L1 16KB/32B 4-way (128 set) write-back-locking-C VIPT Data cache
vfp0 at cpu0: VFP11, rounding, exceptions
fclock0 at simplebus2: 19200000 Hz fixed clock (osc)
fclock1 at simplebus2: 480000000 Hz fixed clock (otg)
bcmicu0 at simplebus1
bcmcprman0 at simplebus1: BCM283x Clock Controller
bcmtmr0 at simplebus1: VC System Timer
bcmtmr0: interrupting on icu irq 3
bcmaux0 at simplebus1
/soc/thermal@7e212000 at simplebus1 not configured
bcmgpio0 at simplebus1: GPIO controller 2835
bcmgpio0: pins 0..31 interrupting on icu irq 49
bcmgpio0: pins 32..54 interrupting on icu irq 50
gpio0 at bcmgpio0: 54 pins
bcmdmac0 at simplebus1: DMA0 DMA2 DMA4 DMA5 DMA8 DMA9 DMA10 DMA11
/soc/power at simplebus1 not configured
/wifi-pwrseq at simplebus0 not configured
/phy at simplebus0 not configured
bsciic0 at simplebus1: Broadcom Serial Controller
bsciic0: interrupting on icu irq 53
iic0 at bsciic0: I2C bus
bcmmbox0 at simplebus1: VC mailbox
bcmmbox0: interrupting on icu irq 65
vcmbox0 at bcmmbox0
/soc/firmware at simplebus1 not configured
/soc/txp@7e004000 at simplebus1 not configured
plcom0 at simplebus1: ARM PL011 UART
plcom0: txfifo 16 bytes
plcom0: interrupting on icu irq 57
bcmsdhost0 at simplebus1: SD HOST controller
bcmsdhost0: interrupting on icu irq 56
bsciic1 at simplebus1: Broadcom Serial Controller
bsciic1: interrupting on icu irq 53
iic1 at bsciic1: I2C bus
com0 at simplebus1: BCM AUX UART, 1-byte FIFO
com0: console
com0: interrupting on icu irq 29
sdhc0 at simplebus1: SDHC controller
sdhc0: interrupting on icu irq 62
bsciic2 at simplebus1: Broadcom Serial Controller
bsciic2: interrupting on icu irq 53
iic2 at bsciic2: I2C bus
dwctwo0 at simplebus1: USB controller
dwctwo0: interrupting on icu irq 9
bcmpmwdog0 at simplebus1: Power management, Reset and Watchdog controller
/soc/vec@7e806000 at simplebus1 not configured
/soc/hdmi@7e902000 at simplebus1 not configured
/soc/gpu at simplebus1 not configured
genfb0 at simplebus1: switching to framebuffer console
genfb0: framebuffer at 0x5e876000, size 1280x720, depth 32, stride 5120
wsdisplay0 at genfb0 kbdmux 1: console (default, vt100 emulation)
wsmux1: connecting to wsdisplay0
wsdisplay0: screen 1-3 added (default, vt100 emulation)
vchiq0 at simplebus1: BCM2835 VCHIQ
/arm-pmu at simplebus0 not configured
gpioleds0 at simplebus0: ACT
bcmrng0 at simplebus1: RNG
entropy: ready
timecounter: Timecounter "bcmtmr0" frequency 1000000 Hz quality 100
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
sdmmc0 at bcmsdhost0
sdhc0: SDHC 3.0, rev 153, caps <01610000/00000000>, platform DMA, 200000
kHz, HS 3.3V, re-tuning mode 1, 1024 byte blocks
sdmmc1 at sdhc0 slot 0
dwctwo0: Core Release: 2.80a (snpsid=4f54280a)
usb0 at dwctwo0: USB revision 2.0
uhub0 at usb0: NetBSD (0x0000) DWC2 root hub (0x0000), class 9/0, rev
2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
IPsec: Initialized Security Association Processing.
sdmmc0: direct I/O error 5, r=6 p=0xc96edf14 write
sdmmc0: SD card status: 4-bit, C10
ld0 at sdmmc0: <0x03:0x5344:SL16G:0x80:0xed7b3c40:0x113>
ld0: 15193 MB, 7717 cyl, 64 head, 63 sec, 512 bytes/sect x 31116288 sectors
ld0: 4-bit width, High-Speed/SDR25, 50.000 MHz
sdmmc1: 4-bit width, 50.000 MHz
bwfm0 at sdmmc1 function 1
(manufacturer 0x2d0, product 0xa9a6) at sdmmc1 function 2 not configured
bwfm1 at uhub0 port 1: Broadcom (0x0a5c) BCMUSB 802.11 Wireless Adapter
(0xbd1e), rev 2.00/0.01, addr 2
uhub0: autoconfiguration error: illegal enable change, port 1
swwdog0: software watchdog initialized
WARNING: 1 error while detecting hardware; check system log.
boot device: ld0
root on ld0a dumps on ld0b
root file system type: ffs
kern.module.path=/stand/evbarm/10.99.7/modules
vchiq0: interrupting on icu irq 66
vchiq: vchiq_init_state: slot_zero = 0xc9b30000, is_master = 0
vchiq: local ver 8 (min 3), remote ver 8.
vcaudio0 at vchiq0: auds
notice: vchiq_get_state: g_state.remote->initialised != 1 (0)
bwfm0: Firmware file default: brcmfmac43430-sdio.bin
bwfm0: Firmware file model-spec:
brcmfmac43430-sdio.raspberrypi,model-zero-w.bin
WARNING: no TOD clock present
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
audio0 at vcaudio0: playback
audio0: slinear_le:16 -> slinear_le:16 2ch 48000Hz, blk 7680 bytes
(40ms) for playback
spkr0 at audio0: PC Speaker (synthesized)
wsbell at spkr0 not configured
bwfm1: address a0:64:8f:55:f6:9c
bwfm1: wl0: Apr 3 2014 04:43:32 version 6.10.198.66 (r467479) FWID
01-32bd010e
bwfm0: Found Firmware file: brcmfmac43430-sdio.bin
bwfm0: NVRAM file default: brcmfmac43430-sdio.txt
bwfm0: NVRAM file model-spec:
brcmfmac43430-sdio.raspberrypi,model-zero-w.txt
bwfm0: Found NVRAM file: brcmfmac43430-sdio.raspberrypi,model-zero-w.txt
bwfm0: CLM file default: brcmfmac43430-sdio.clm_blob
bwfm0: CLM file model-spec:
brcmfmac43430-sdio.raspberrypi,model-zero-w.clm_blob
bwfm0: CHIPACTIVE
bwfm0: address b8:27:eb:5b:ff:03
bwfm0: wl0: Oct 23 2017 03:55:53 version 7.45.98.38 (r674442 CY) FWID
01-e58d219f
wsdisplay0: screen 4 added (default, vt100 emulation)
Home |
Main Index |
Thread Index |
Old Index