Re: kern/55243: panic at usb_transfer_complete() on raspberry pi 4

[Kouichi Hashikawa <hashikaw%mail.ru@localhost>]

dmesg is following.
if I use ure0 or other USB ethernet (like axen0), panic occurred.



rebooting...
pool redzone disabled for 'kmem-04096'
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
    2018, 2019, 2020 The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.
NetBSD 9.99.56 (GENERIC64) #0: Thu Apr 16 09:51:57 UTC 2020
        mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/evbarm/compile/GENERIC64
total memory = 3939 MB
avail memory = 3812 MB
pool redzone disabled for 'buf4k'
pool redzone disabled for 'buf64k'
timecounter: Timecounters tick every 10.000 msec
running cgd selftest aes-xts-256 aes-xts-512 done
armfdt0 (root)
simplebus0 at armfdt0: Raspberry Pi 4 Model B Rev 1.2
simplebus1 at simplebus0
simplebus2 at simplebus0
cpus0 at simplebus0
simplebus3 at simplebus0
simplebus4 at simplebus0
cpu0 at cpus0: Arm Cortex-A72 r0p3 (v8-A), id 0x0
cpu0: IC enabled, DC enabled, EL0/EL1 stack Alignment check enabled
cpu0: Cache Writeback Granule 16B, Exclusives Reservation Granule 16B
cpu0: Dcache line 64, Icache line 64
cpu0: L1 48KB/64B 3-way read-allocate PIPT Instruction cache
cpu0: L1 32KB/64B 2-way write-back read-allocate write-allocate PIPT Data cache
cpu0: L2 1024KB/64B 16-way write-back read-allocate write-allocate PIPT Unified cache
cpu0: revID=0x0, PMCv3, 4k table, 64k table, 16bit ASID
cpu0: auxID=0x10000, FP, CRC32, NEON, rounding, NaN propagation, denormals, 32x64bitRegs, Fused Multiply-Add
cpu1 at cpus0: Arm Cortex-A72 r0p3 (v8-A), id 0x1
cpu2 at cpus0: Arm Cortex-A72 r0p3 (v8-A), id 0x2
cpu3 at cpus0: Arm Cortex-A72 r0p3 (v8-A), id 0x3
simplebus5 at simplebus1
gic0 at simplebus1: GIC
armgic0 at gic0: Generic Interrupt Controller, 256 sources (247 valid)
armgic0: 16 Priorities, 224 SPIs, 7 PPIs, 16 SGIs
syscon0 at simplebus1: System Controller Registers
fclock0 at simplebus2: 54000000 Hz fixed clock (osc)
bcmcprman0 at simplebus1: BCM283x Clock Controller
bcmaux0 at simplebus1
fclock1 at simplebus2: 480000000 Hz fixed clock (otg)
bcmicu0 at simplebus1: Multiprocessor
gtmr0 at simplebus0: Generic Timer
gtmr0: interrupting on GIC irq 27
armgtmr0 at gtmr0: Generic Timer (54000 kHz, virtual)
timecounter: Timecounter "armgtmr0" frequency 54000000 Hz quality 500
bcmgpio0 at simplebus1: GPIO controller 2838
bcmgpio0: pins 0..31 interrupting on GIC irq 145
bcmgpio0: pins 32..58 interrupting on GIC irq 146
gpio0 at bcmgpio0: 58 pins
gregulator0 at simplebus0: vdd-sd-io
gregulator0: autoconfiguration error: cannot get pin 0
plcom0 at simplebus1: ARM PL011 UART
plcom0: txfifo disabled
plcom0: interrupting on GIC irq 153
com0 at simplebus1: BCM AUX UART, working fifo
com0: console
com0: interrupting on GIC irq 125
mmcpwrseq0 at simplebus0autoconfiguration error: : couldn't get reset GPIOs
/soc/avs-monitor@7d5d2000/thermal at syscon0 not configured
/soc/firmware/gpio at simplebus5 not configured
/soc/power at simplebus1 not configured
/phy at simplebus0 not configured
bcmmbox0 at simplebus1: VC mailbox
bcmmbox0: interrupting on GIC irq 65
vcmbox0 at bcmmbox0
/scb/pcie@7d500000 at simplebus3 not configured
genet0 at simplebus3: GENETv5.0
genet0: Ethernet address ....
brgphy0 at genet0 phy 1: BCM54213PE 1000BASE-T media interface, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
genet0: interrupting on GIC irq 189
/soc/timer@7e003000 at simplebus1 not configured
/soc/txp@7e004000 at simplebus1 not configured
bsciic0 at simplebus1: Broadcom Serial Controller
bsciic0: interrupting on GIC irq 149
iic0 at bsciic0: I2C bus
sdhc0 at simplebus1: SDHC controller
sdhc0: interrupting on GIC irq 158
bsciic1 at simplebus1: Broadcom Serial Controller
bsciic1: interrupting on GIC irq 149
iic1 at bsciic1: I2C bus
/soc/vec@7e806000 at simplebus1 not configured
dwctwo0 at simplebus1: USB controller
dwctwo0: interrupting on GIC irq 105
bcmdmac0 at simplebus1: DMA0 DMA2 DMA4 DMA5 DMA6 DMA7
bcmpmwdog0 at simplebus1: Power management, Reset and Watchdog controller
/soc/pwm@7e20c800 at simplebus1 not configured
/soc/mailbox@7e00b840 at simplebus1 not configured
sdhc1 at simplebus4: SDHC controller
sdhc1: interrupting on GIC irq 158
/chosen at simplebus0 not configured
armpmu0 at simplebus0: Performance Monitor Unit
gpioleds0 at simplebus0: ACT
/soc/hvs@7e400000 at simplebus1 not configured
/soc/rng@7e104000 at simplebus1 not configured
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
cpu2: IC enabled, DC enabled, EL0/EL1 stack Alignment check enabled
cpu2: Cache Writeback Granule 16B, Exclusives Reservation Granule 16B
cpu2: Dcache line 64, Icache line 64
cpu2: L1 48KB/64B 3-way read-allocate PIPT Instruction cache
cpu2: L1 32KB/64B 2-way write-back read-allocate write-allocate PIPT Data cache
cpu2: L2 1024KB/64B 16-way write-back read-allocate write-allocate PIPT Unified cache
cpu2: revID=0x0, PMCv3, 4k table, 64k table, 16bit ASID
cpu2: auxID=0x10000, FP, CRC32, NEON, rounding, NaN propagation, denormals, 32x64bitRegs, Fused Multiply-Add
cpu1: IC enabled, DC enabled, EL0/EL1 stack Alignment check enabled
cpu1: Cache Writeback Granule 16B, Exclusives Reservation Granule 16B
cpu1: Dcache line 64, Icache line 64
cpu1: L1 48KB/64B 3-way read-allocate PIPT Instruction cache
cpu1: L1 32KB/64B 2-way write-back read-allocate write-allocate PIPT Data cache
cpu1: L2 1024KB/64B 16-way write-back read-allocate write-allocate PIPT Unified cache
cpu1: revID=0x0, PMCv3, 4k table, 64k table, 16bit ASID
cpu1: auxID=0x10000, FP, CRC32, NEON, rounding, NaN propagation, denormals, 32x64bitRegs, Fused Multiply-Add
cpu3: IC enabled, DC enabled, EL0/EL1 stack Alignment check enabled
cpu3: Cache Writeback Granule 16B, Exclusives Reservation Granule 16B
cpu3: Dcache line 64, Icache line 64
cpu3: L1 48KB/64B 3-way read-allocate PIPT Instruction cache
cpu3: L1 32KB/64B 2-way write-back read-allocate write-allocate PIPT Data cache
cpu3: L2 1024KB/64B 16-way write-back read-allocate write-allocate PIPT Unified cache
cpu3: revID=0x0, PMCv3, 4k table, 64k table, 16bit ASID
cpu3: auxID=0x10000, FP, CRC32, NEON, rounding, NaN propagation, denormals, 32x64bitRegs, Fused Multiply-Add
sdhc0: SDHC 3.0, rev 153, PIO, 250000 kHz, HS 3.3V, re-tuning mode 1, 1024 byte blocks
sdmmc0 at sdhc0 slot 0
dwctwo0: Core Release: 2.80a (snpsid=4f54280a)
usb0 at dwctwo0: USB revision 2.0
sdhc1: SDHC 3.0, rev 16, PIO, 100000 kHz, HS 3.3V, re-tuning mode 1, 1024 byte blocks
sdmmc1 at sdhc1 slot 0
armpmu0: interrupting on GIC irq 48
armpmu0: interrupting on GIC irq 49
armpmu0: interrupting on GIC irq 50
armpmu0: interrupting on GIC irq 51
uhub0 at usb0: NetBSD (0x0000) DWC2 root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
IPsec: Initialized Security Association Processing.
sdmmc1: SD card status: 4-bit, C10, U1
ld1 at sdmmc1: <....>
ld1: 59376 MB, 7569 cyl, 255 head, 63 sec, 512 bytes/sect x 121602048 sectors
ld1: 4-bit width, High-Speed/SDR25, 50.000 MHz
sdmmc0: 4-bit width, 50.000 MHz
sdmmc0: SDIO function
bwfm0 at sdmmc0 function 1
(manufacturer 0x2d0, product 0xa9a6) at sdmmc0 function 2 not configured
(manufacturer 0x2d0, product 0xa9a6, standard function interface code 0x2) at sdmmc0 function 3 not configured
uhub1 at uhub0 port 1: VIA Labs, Inc. (0x2109) USB2.0 Hub (0x2813), class 9/0, rev 2.10/90.14, addr 2
uhub1: single transaction translator
uhub1: 4 ports with 4 removable, self powered
ure0 at uhub1 port 1
ure0: Realtek (0x0bda) USB 10/100/1000 LAN (0x8153), rev 2.10/30.00, addr 3
ure0: RTL8153 ver 5c30
rgephy0 at ure0 phy 0: RTL8251 1000BASE-T media interface, rev. 0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, auto
ure0: Ethernet address ....
umass0 at uhub1 port 2 configuration 1 interface 0
umass0: Logitec (0x0789) LGB USB Device (0x0275), rev 2.10/66.01, addr 4
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0uhub0: autoconfiguration error: illegal enable change, port 1
 target 0 lun 0: <....> disk fixed
sd0: fabricating a geometry
sd0: 232 GB, 238475 cyl, 64 head, 32 sec, 512 bytes/sect x 488397168 sectors
sd0: fabricating a geometry
WARNING: 3 errors while detecting hardware; check system log.
boot device: ld1
root on ld1a dumps on ld1b
root file system type: ffs
kern.module.path=/stand/evbarm/9.99.56/modules
bwfm0: Firmware file default:    brcmfmac43455-sdio.bin
WARNING: no TOD clock present
bwfm0: Firmware file model-spec: brcmfmac43455-sdio.raspberrypi,4-model-b.bin
WARNING: using filesystem time
WARNING: CHECK AND RESET THE DATE!
bwfm0: Found Firmware file: brcmfmac43455-sdio.bin
bwfm0: NVRAM file default:    brcmfmac43455-sdio.txt
bwfm0: NVRAM file model-spec: brcmfmac43455-sdio.raspberrypi,4-model-b.txt
bwfm0: Found NVRAM file: brcmfmac43455-sdio.raspberrypi,4-model-b.txt
bwfm0: CHIPACTIVE
bwfm0: wl0: Mar  1 2015 07:29:38 version 7.45.18 (r538002) FWID 01-6a2c8ad4
bwfm0: address ....
 

-- 
Kouichi Hashikawa