Re: bin/53961: dhcpcd doesn't work with bge*

[John Klos <john%klos.com@localhost>]

The following reply was made to PR bin/53961; it has been noted by GNATS.

From: John Klos <john%klos.com@localhost>
To: gnats-bugs%netbsd.org@localhost
Cc: roy%netbsd.org@localhost, gnats-admin%netbsd.org@localhost, netbsd-bugs%netbsd.org@localhost
Subject: Re: bin/53961: dhcpcd doesn't work with bge*
Date: Tue, 9 Apr 2019 19:27:23 +0000 (UTC)

 > Can you post the output of `ifconfig bge0` on the troublesome system please?
 
 Sure. VLANs weren't in use until after trying to run dhcpcd:
 
 bge0: flags=0x8b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST> mtu 1500
          capabilities=3f80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx>
          capabilities=3f80<UDP4CSUM_Rx,UDP4CSUM_Tx>
          enabled=3f80<TSO4,IP4CSUM_Rx,IP4CSUM_Tx,TCP4CSUM_Rx,TCP4CSUM_Tx>
          enabled=3f80<UDP4CSUM_Rx,UDP4CSUM_Tx>
          ec_capabilities=7<VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU>
          ec_enabled=3<VLAN_MTU,VLAN_HWTAGGING>
          address: 00:10:18:e4:20:e0
          media: Ethernet autoselect (1000baseT full-duplex)
          status: active
          inet 23.130.97.130/30 broadcast 23.130.97.131 flags 0x0
          inet6 fe80::210:18ff:fee4:20e0%bge0/64 flags 0x0 scopeid 0x1
 
 This system is in a datacenter now, so I can't try updating, but another 
 system I have has the same issue with re0. It's an amd64 system. I've 
 updated to -8 from today (9-April-2019) and get:
 
 re0 at pci5 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet (rev. 0x06)
 re0: interrupting at msi1 vec 0
 re0: Ethernet address 30:b5:c2:05:07:97
 re0: using 256 tx descriptors
 rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 4
 ...
 re1 at pci8 dev 0 function 0: RealTek 8168/8111 PCIe Gigabit Ethernet (rev. 0x11)
 re1: interrupting at msi3 vec 0
 re1: Ethernet address 70:85:c2:7f:83:05
 re1: using 256 tx descriptors
 rgephy1 at re1 phy 7: RTL8251 1000BASE-T media interface, rev. 0
 
 One is the motherboard ethernet and the other is a PCIe ethernet.
 
 re0: interface not found or invalid
 dhcpcd exited
 
 dhcpcd re1
 re1: interface not found or invalid
 dhcpcd exited
 
 If it's easier, I can give you a shell on this machine.
 
 John Klos