NetBSD-Bugs archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
Re: port-xen/47499: recent amd64 DOM0 kernel hangs at boot
The following reply was made to PR port-xen/47499; it has been noted by GNATS.
From: Takahiro HAYASHI <t-hash%abox3.so-net.ne.jp@localhost>
To: gnats-bugs%NetBSD.org@localhost
Cc: port-xen-maintainer%NetBSD.org@localhost, gnats-admin%NetBSD.org@localhost,
netbsd-bugs%NetBSD.org@localhost
Subject: Re: port-xen/47499: recent amd64 DOM0 kernel hangs at boot
Date: Mon, 25 Mar 2013 20:35:32 +0900
Hi,
I applied chuq's patch
http://ftp.netbsd.org/pub/NetBSD/misc/chs/diff.acpi-sci.4
to 201303021320Z tree and built kernel with MPDEBUG and MPVERBOSE.
That works fine.
I updated Xen kernel to 4.1.4nb1 but it did not give significant
changes.
I attach the differences between boot logs from old and patched
kernel and whole of boot log from fixed kernel.
Thank you very much.
--- bootlog.old 2013-03-25 20:04:51.000000000 +0900
+++ bootlog.fixed 2013-03-25 20:04:23.000000000 +0900
@@ -59,7 +59,7 @@
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) Table is not found!
(XEN) Using scheduler: SMP Credit Scheduler (credit)
-(XEN) Detected 2500.186 MHz processor.
+(XEN) Detected 2500.222 MHz processor.
(XEN) Initing memory sharing.
(XEN) AMD-Vi: IOMMU not found!
(XEN) I/O virtualisation disabled
@@ -101,7 +101,7 @@
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
-NetBSD 6.99.17 (XEN3_DOM0) #0: Mon Mar 4 01:51:12 JST 2013
+NetBSD 6.99.17 (XEN3_DOM0) #0: Mon Mar 25 19:46:32 JST 2013
root@halt:/usr/build2/201303021320Z/obj.amd64/sys/arch/amd64/compile/XEN3_DOM0
total memory = 256 MB
avail memory = 232 MB
@@ -148,7 +148,7 @@
xencons0: using event channel 2
acpi0 at hypervisor0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <062310,RSDT1051,20100623>, AslId <MSFT,00000097>
-ioapic0: int9
0x19958<vector=0x58,delmode=0x1,logical,pending,level,masked,dest=0x0>
0x1000000<target=0x1>
+ioapic0: int9
0x1a958<vector=0x58,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x1000000<target=0x1>
mpacpi: found root PCI bus 0
mpacpi: found subordinate bus 0
mpacpi: found subordinate bus 0
@@ -160,47 +160,6 @@
mpacpi: configuring PCI bus 1 int routing
mpacpi: configuring PCI bus 2 int routing
mpacpi: configuring PCI bus 3 int routing
-ioapic0 reenabling
-(XEN) ioapic_guest_write: apic=0, pin=0, irq=0
-(XEN) ioapic_guest_write: new_entry=000109f0
-(XEN) ioapic_guest_write: old_entry=00010000 pirq=0
-(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
-ioapic0: int0 0x10000<vector=0x0,delmode=0x0,masked,dest=0x0> 0x0<target=0x0>
-ioapic0: int1 0x928<vector=0x28,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-(XEN) ioapic_guest_write: apic=0, pin=2, irq=0
-(XEN) ioapic_guest_write: new_entry=000109f0
-(XEN) ioapic_guest_write: old_entry=000009f0 pirq=0
-(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
-ioapic0: int2 0x9f0<vector=0xf0,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int3 0x930<vector=0x30,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-(XEN) ioapic_guest_write: apic=0, pin=4, irq=4
-(XEN) ioapic_guest_write: new_entry=000109f1
-(XEN) ioapic_guest_write: old_entry=000009f1 pirq=0
-(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
-ioapic0: int4 0x9f1<vector=0xf1,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int5 0x938<vector=0x38,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int6 0x940<vector=0x40,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int7 0x948<vector=0x48,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int8 0x950<vector=0x50,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-(XEN) ioapic_guest_write: apic=0, pin=9, irq=9
-(XEN) ioapic_guest_write: new_entry=0000a958
-(XEN) ioapic_guest_write: old_entry=0000d958 pirq=200
-(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
-ioapic0: int9
0xd958<vector=0x58,delmode=0x1,logical,pending,irrpending,level,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int10 0x960<vector=0x60,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int11 0x968<vector=0x68,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int12 0x970<vector=0x70,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int13 0x978<vector=0x78,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int14 0x988<vector=0x88,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int15 0x990<vector=0x90,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
-ioapic0: int16
0x1a9b0<vector=0xb0,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
-ioapic0: int17
0x1a9b8<vector=0xb8,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
-ioapic0: int18
0x1a9c0<vector=0xc0,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
-ioapic0: int19
0x1a9c8<vector=0xc8,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
-ioapic0: int20
0x1a9d0<vector=0xd0,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
-ioapic0: int21
0x1a9d8<vector=0xd8,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
-ioapic0: int22
0x1a921<vector=0x21,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
-ioapic0: int23
0x1a929<vector=0x29,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
ioapic0: pin 2 attached to isa0 irq 0 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 1 attached to isa0 irq 1 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 3 attached to isa0 irq 3 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
@@ -411,4 +370,82 @@
timecounter: Timecounter "xen_system_time" frequency 1000000000 Hz quality
10000
Xen clock: using event channel 11
xenbus0: using event channel 12
+atapibus0 at atabus3: 2 targets
+uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
+uhub0: 3 ports with 3 removable, self powered
+uhub1 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
+uhub1: 3 ports with 3 removable, self powered
+uhub2 at usb2: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
+uhub2: 6 ports with 6 removable, self powered
+uhub3 at usb3: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
+uhub3: 3 ports with 3 removable, self powered
+uhub4 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
+uhub4: 3 ports with 3 removable, self powered
+uhub5 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
+uhub5: 6 ports with 6 removable, self powered
+uhub6 at usb6: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
+uhub6: 2 ports with 2 removable, self powered
+cd0 at atapibus0 drive 1: <PIONEER DVD-RW DVR-110, EJTO028893WL, 8.22> cdrom
removable
+cd0: 32-bit data port
+cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
+wd0 at atabus3 drive 0
+wd0: <Maxtor 6L160P0>
+wd0: drive supports 16-sector PIO transfers, LBA48 addressing
+wd0: 152 GB, 317629 cyl, 16 head, 63 sec, 512 bytes/sect x 320170943 sectors
+wd0: 32-bit data port
+wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
+wd0(ixpide1:1:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
+cd0(ixpide1:1:1): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
+ehci0: handing over low speed device on port 1 to ohci0
+crypto: assign driver 0, flags 2
+crypto: driver 0 registers alg 1 flags 0 maxoplen 0
+crypto: driver 0 registers alg 2 flags 0 maxoplen 0
+crypto: driver 0 registers alg 3 flags 0 maxoplen 0
+crypto: driver 0 registers alg 4 flags 0 maxoplen 0
+crypto: driver 0 registers alg 5 flags 0 maxoplen 0
+crypto: driver 0 registers alg 26 flags 0 maxoplen 0
+crypto: driver 0 registers alg 27 flags 0 maxoplen 0
+crypto: driver 0 registers alg 29 flags 0 maxoplen 0
+crypto: driver 0 registers alg 33 flags 0 maxoplen 0
+crypto: driver 0 registers alg 17 flags 0 maxoplen 0
+crypto: driver 0 registers alg 6 flags 0 maxoplen 0
+crypto: driver 0 registers alg 19 flags 0 maxoplen 0
+crypto: driver 0 registers alg 7 flags 0 maxoplen 0
+crypto: driver 0 registers alg 20 flags 0 maxoplen 0
+crypto: driver 0 registers alg 15 flags 0 maxoplen 0
+crypto: driver 0 registers alg 24 flags 0 maxoplen 0
+crypto: driver 0 registers alg 25 flags 0 maxoplen 0
+crypto: driver 0 registers alg 8 flags 0 maxoplen 0
+crypto: driver 0 registers alg 21 flags 0 maxoplen 0
+crypto: driver 0 registers alg 16 flags 0 maxoplen 0
+crypto: driver 0 registers alg 9 flags 0 maxoplen 0
+crypto: driver 0 registers alg 10 flags 0 maxoplen 0
+crypto: driver 0 registers alg 13 flags 0 maxoplen 0
+crypto: driver 0 registers alg 14 flags 0 maxoplen 0
+crypto: driver 0 registers alg 28 flags 0 maxoplen 0
+crypto: driver 0 registers alg 30 flags 0 maxoplen 0
+crypto: driver 0 registers alg 31 flags 0 maxoplen 0
+crypto: driver 0 registers alg 32 flags 0 maxoplen 0
+crypto: driver 0 registers alg 11 flags 0 maxoplen 0
+crypto: driver 0 registers alg 18 flags 0 maxoplen 0
+crypto: driver 0 registers alg 23 flags 0 maxoplen 0
+crypto: driver 0 registers alg 22 flags 0 maxoplen 0
+Kernelized RAIDframe activated
+boot device: wd0
+root on wd0a dumps on wd0b
+Your machine does not initialize mem_clusters; sparse_dumps disabled
+root file system type: ffs
+Enter pathname of shell or RETURN for /bin/sh: uhidev0 at uhub0 port 1
configuration 1 interface 0
+uhidev0: vendor 0x05c7 Generic USB K/B, rev 1.10/0.01, addr 2, iclass 3/1
+ukbd0 at uhidev0: 8 modifier keys, 6 key codes
+wskbd0 at ukbd0 mux 1
+wskbd0: connecting to wsdisplay0
+uhidev1 at uhub0 port 1 configuration 1 interface 1
+uhidev1: vendor 0x05c7 Generic USB K/B, rev 1.10/0.01, addr 2, iclass 3/1
+uhidev1: 3 report ids
+ums0 at uhidev1 reportid 1: 3 buttons and Z dir
+wsmouse0 at ums0 mux 0
+uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
+uhid1 at uhidev1 reportid 3: input=4, output=0, feature=0
+#
The whole of boot log from fixed kernel is:
>> NetBSD/x86 BIOS Boot, Revision 5.9 (from NetBSD 6.99.16)
>> Memory: 639/2030272 k
1. Boot NetBSD/i386
2. Boot NetBSD/i386 with -s
3. Boot NetBSD/amd64
4. Boot NetBSD/amd64 with -s
5. Xen4.1.3 -sv
6. Xen4.1.3 (hd0f) -asv
7. Drop to boot prompt
Choose an option; RETURN for default; SPACE to stop countdown.
Option 1 will be chosen in 0 seconds.
1448808+312472=0x1ae0c0
Loading /netbsd.xen
__ __ _ _ _ _ _
\ \/ /___ _ __ | || | / || || |
\ // _ \ '_ \ | || |_ | || || |_
/ \ __/ | | | |__ _|| ||__ _|
/_/\_\___|_| |_| |_|(_)_(_) |_|
(XEN) Xen version 4.1.4 (root@) (gcc version 4.5.3 (NetBSD nb2 20110806) ) Sat
Mar 16 22:41:41 JST 2013
(XEN) Latest ChangeSet: unavailable
(XEN) Bootloader: unknown
(XEN) Command line: dom0_mem=256M console=com1 com1=115200,8n1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: V2; EDID transfer time: 1 seconds
(XEN) EDID info not retrieved because of reasons unknown
(XEN) Disc information:
(XEN) Found 1 MBR signatures
(XEN) Found 1 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009fc00 (usable)
(XEN) 000000000009fc00 - 00000000000a0000 (reserved)
(XEN) 00000000000e6000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 000000007bfb0000 (usable)
(XEN) 000000007bfb0000 - 000000007bfbe000 (ACPI data)
(XEN) 000000007bfbe000 - 000000007bfe0000 (ACPI NVS)
(XEN) 000000007bfe0000 - 000000007c000000 (reserved)
(XEN) 00000000ff700000 - 0000000100000000 (reserved)
(XEN) System RAM: 1983MB (2030908kB)
(XEN) ACPI: RSDP 000FAF00, 0014 (r0 ACPIAM)
(XEN) ACPI: RSDT 7BFB0000, 0040 (r1 062310 RSDT1051 20100623 MSFT 97)
(XEN) ACPI: FACP 7BFB0200, 0084 (r1 062310 FACP1051 20100623 MSFT 97)
(XEN) ACPI Warning (tbfadt-0444): Optional field "Pm2ControlBlock" has zero
address or length: 0000000000000000/1 [20070126]
(XEN) ACPI: DSDT 7BFB0450, 931F (r1 RS78D RS78D40B 40B INTL 20051117)
(XEN) ACPI: FACS 7BFBE000, 0040
(XEN) ACPI: APIC 7BFB0390, 007C (r1 062310 APIC1051 20100623 MSFT 97)
(XEN) ACPI: MCFG 7BFB0410, 003C (r1 062310 OEMMCFG 20100623 MSFT 97)
(XEN) ACPI: OEMB 7BFBE040, 0072 (r1 062310 OEMB1051 20100623 MSFT 97)
(XEN) ACPI: SRAT 7BFB9770, 00A0 (r3 AMD FAM_F_10 2 AMD 1)
(XEN) ACPI: HPET 7BFB9810, 0038 (r1 062310 OEMHPET 20100623 MSFT 97)
(XEN) ACPI: SSDT 7BFB9850, 028A (r1 A M I POWERNOW 1 AMD 1)
(XEN) Domain heap initialised
(XEN) Processor #0 15:11 APIC version 16
(XEN) Processor #1 15:11 APIC version 16
(XEN) IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) Table is not found!
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2500.222 MHz processor.
(XEN) Initing memory sharing.
(XEN) AMD-Vi: IOMMU not found!
(XEN) I/O virtualisation disabled
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) Platform timer is 14.318MHz HPET
(XEN) Allocated console ring of 16 KiB.
(XEN) HVM: ASIDs enabled.
(XEN) SVM: Supported advanced features:
(XEN) - Last Branch Record (LBR) Virtualisation
(XEN) HVM: SVM enabled
(XEN) AMD: Disabling C1 Clock Ramping Node #0
(XEN) Brought up 2 CPUs
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, lsb, paddr 0xffffffff80000000 -> 0xffffffff80e5d000
(XEN) Dom0 symbol map 0xffffffff80e5d000 -> 0xffffffff80f7d888
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000076000000->0000000078000000 (57344 pages to be
allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff80000000->ffffffff80f7d888
(XEN) Init. ramdisk: ffffffff80f7e000->ffffffff80f7e000
(XEN) Phys-Mach map: ffffffff80f7e000->ffffffff80ffe000
(XEN) Start info: ffffffff80ffe000->ffffffff80ffe4b4
(XEN) Page tables: ffffffff80fff000->ffffffff8100c000
(XEN) Boot stack: ffffffff8100c000->ffffffff8100d000
(XEN) TOTAL: ffffffff80000000->ffffffff81400000
(XEN) ENTRY ADDRESS: ffffffff80100000
(XEN) Dom0 has maximum 2 VCPUs
(XEN) Scrubbing Free RAM: .................done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: Errors and warnings
(XEN) Guest Loglevel: Nothing (Rate-limited: Errors and warnings)
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to
Xen)
(XEN) Freed 212kB init memory.
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.99.17 (XEN3_DOM0) #0: Mon Mar 25 19:46:32 JST 2013
root@halt:/usr/build2/201303021320Z/obj.amd64/sys/arch/amd64/compile/XEN3_DOM0
total memory = 256 MB
avail memory = 232 MB
timecounter: Timecounters tick every 10.000 msec
mainbus0 (root)
mainbus0: scanning 0x9fc00 to 0x9fff0 for MP signature
mainbus0: scanning 0x9f800 to 0x9fbf0 for MP signature
mainbus0: scanning 0xf0000 to 0xffff0 for MP signature
mainbus0: MP floating pointer found in bios at 0xff780
mainbus0: MP config table at 0xe5e10, 364 bytes long
ACPI Warning: Optional field Pm2ControlBlock has zero address or length:
0x0000000000000000/0x1 (20110623/tbfadt-586)
cpu0 at mainbus0 apid 0
cpu1 at mainbus0 apid 1
ioapic0 at mainbus0 apid 2: pa 0xfec00000, virtual wire mode, version 21, 24
pins
(XEN) ioapic_guest_write: apic=0, pin=0, irq=0
(XEN) ioapic_guest_write: new_entry=000109f0
(XEN) ioapic_guest_write: old_entry=00010000 pirq=0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) ioapic_guest_write: apic=0, pin=2, irq=0
(XEN) ioapic_guest_write: new_entry=000109f0
(XEN) ioapic_guest_write: old_entry=000009f0 pirq=0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) irq.c:1624: dom0: pirq 0 or irq 3 already mapped
(XEN) ioapic_guest_write: apic=0, pin=4, irq=4
(XEN) ioapic_guest_write: new_entry=000109f1
(XEN) ioapic_guest_write: old_entry=000009f1 pirq=0
(XEN) ioapic_guest_write: Attempt to modify IO-APIC pin for in-use IRQ!
(XEN) irq.c:1624: dom0: pirq 0 or irq 5 already mapped
(XEN) irq.c:1624: dom0: pirq 0 or irq 6 already mapped
(XEN) irq.c:1624: dom0: pirq 0 or irq 7 already mapped
(XEN) irq.c:1624: dom0: pirq 0 or irq 8 already mapped
(XEN) irq.c:1624: dom0: pirq 0 or irq 9 already mapped
(XEN) irq.c:1624: dom0: pirq 0 or irq 10 already mapped
(XEN) irq.c:1624: dom0: pirq 0 or irq 11 already mapped
(XEN) irq.c:1624: dom0: pirq 0 or irq 12 already mapped
(XEN) irq.c:1624: dom0: pirq 0 or irq 13 already mapped
hypervisor0 at mainbus0: Xen version 4.1.4
VIRQ_DEBUG interrupt using event channel 1
vcpu0 at hypervisor0: AMD Athlon(tm) Dual Core Processor 4850e, id 0x60fb2
vcpu0: idle lwp at 0xffffa0000071a840, idle sp at 0x0xffffa0000c2dfc50
xenbus0 at hypervisor0: Xen Virtual Bus Interface
xencons0 at hypervisor0: Xen Virtual Console Driver
xencons0: console major 143, unit 0
xencons0: using event channel 2
acpi0 at hypervisor0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <062310,RSDT1051,20100623>, AslId <MSFT,00000097>
ioapic0: int9
0x1a958<vector=0x58,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x1000000<target=0x1>
mpacpi: found root PCI bus 0
mpacpi: found subordinate bus 0
mpacpi: found subordinate bus 0
mpacpi: found subordinate bus 0
mpacpi: 4 PCI busses
mpacpi: ISA interrupt override 0 -> 2 (0/0)
mpacpi: ISA interrupt override 9 -> 9 (3/3)
mpacpi: configuring PCI bus 0 int routing
mpacpi: configuring PCI bus 1 int routing
mpacpi: configuring PCI bus 2 int routing
mpacpi: configuring PCI bus 3 int routing
ioapic0: pin 2 attached to isa0 irq 0 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 1 attached to isa0 irq 1 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 3 attached to isa0 irq 3 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 4 attached to isa0 irq 4 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 5 attached to isa0 irq 5 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 6 attached to isa0 irq 6 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 7 attached to isa0 irq 7 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 8 attached to isa0 irq 8 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 9 attached to isa0 irq 9 (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 10 attached to isa0 irq 10 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 11 attached to isa0 irq 11 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 12 attached to isa0 irq 12 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 13 attached to isa0 irq 13 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 14 attached to isa0 irq 14 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 15 attached to isa0 irq 15 (type 0x0<type=0x0> flags
0x0<pol=0x0,trig=0x0>)
ioapic0: pin 18 attached to pci0 device 2 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 2 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 2 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 2 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 3 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 3 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 3 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 3 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 4 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 4 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 4 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 4 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 5 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 5 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 5 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 5 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 6 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 6 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 6 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 6 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 7 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 7 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 7 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 7 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 9 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 9 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 9 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 9 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 10 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 10 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 10 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 10 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 11 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 11 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 11 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 11 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 12 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 12 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 12 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 12 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 20 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 20 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 20 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 20 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 18 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 18 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 18 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 18 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci0 device 19 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci0 device 19 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci0 device 19 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci0 device 19 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 22 attached to pci0 device 17 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 18 attached to pci1 device 5 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 19 attached to pci1 device 5 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 16 attached to pci1 device 5 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 17 attached to pci1 device 5 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 20 attached to pci3 device 5 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 21 attached to pci3 device 5 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 22 attached to pci3 device 5 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 23 attached to pci3 device 5 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 21 attached to pci3 device 6 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 22 attached to pci3 device 6 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 23 attached to pci3 device 6 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 20 attached to pci3 device 6 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 22 attached to pci3 device 7 INT_A (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 23 attached to pci3 device 7 INT_B (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 20 attached to pci3 device 7 INT_C (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
ioapic0: pin 21 attached to pci3 device 7 INT_D (type 0x0<type=0x0> flags
0xf<pol=0x3=Act Lo,trig=0x3=Level>)
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
BROD (PNP0C02) at acpi0 not configured
TMR (PNP0100) at acpi0 not configured
pcppi0 at acpi0 (SPKR, PNP0800): io 0x61
UAR1 (PNP0501) at acpi0 not configured
HPET (PNP0103) at acpi0 not configured
OMSC (PNP0C02) at acpi0 not configured
RMSC (PNP0C02) at acpi0 not configured
SIOR (PNP0C02) at acpi0 not configured
PCIE (PNP0C02) at acpi0 not configured
RMEM (PNP0C01) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
AOD (PNP0C14) at acpi0 not configured
pci0 at hypervisor0 bus 0: configuration mode 1
hypervisor0: added to list as bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0: vendor 0x1022 product 0x9600 (rev. 0x00)
ppb0 at pci0 dev 1 function 0: vendor 0x1022 product 0x9602 (rev. 0x00)
pci1 at ppb0 bus 1
ppb0: added to list as bus 1
pci1: i/o space, memory space enabled
vga0 at pci1 dev 5 function 0: vendor 0x1002 product 0x9610 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
ppb1 at pci0 dev 4 function 0: vendor 0x1022 product 0x9604 (rev. 0x00)
ppb1: PCI Express 2.0 <Root Port of PCI-E Root Complex> x1 @ 5.0Gb/s
> x1 @ 2.5Gb/s
pci2 at ppb1 bus 2
ppb1: added to list as bus 2
pci2: i/o space, memory space enabled
mskc0 at pci2 dev 0 function 0ioapic0: int16
0x1a9b0<vector=0xb0,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
, Yukon-2 EC Ultra (0x5): ioapic0 pin 16, event channel 4
msk0 at mskc0 port A: Ethernet address 00:e0:61:xx:xx:xx
ukphy0 at msk0 phy 0: OUI 0x000ac2, model 0x000b, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
ixpide0 at pci0 dev 17 function 0: ATI Technologies IXP IDE Controller (rev.
0x00)
ixpide0: bus-master DMA support present
ixpide0: primary channel configured to native-PCI mode
ioapic0: int22
0x1a921<vector=0x21,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
ixpide0: using ioapic0 pin 22, event channel 5 for native-PCI interrupt
atabus0 at ixpide0 channel 0
ixpide0: secondary channel configured to native-PCI mode
atabus1 at ixpide0 channel 1
ohci0 at pci0 dev 18 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 16, event channel 4
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 18 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 16, event channel 4
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ehci0 at pci0 dev 18 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci0: applying AMD SB600/SB700 USB freeze workaround
ioapic0: int17
0x1a9b8<vector=0xb8,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
ehci0: interrupting at ioapic0 pin 17, event channel 6
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
ohci2 at pci0 dev 19 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ioapic0: int18
0x1a9c0<vector=0xc0,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
ohci2: interrupting at ioapic0 pin 18, event channel 7
ohci2: OHCI version 1.0, legacy support
usb3 at ohci2: USB revision 1.0
ohci3 at pci0 dev 19 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci3: interrupting at ioapic0 pin 18, event channel 7
ohci3: OHCI version 1.0, legacy support
usb4 at ohci3: USB revision 1.0
ehci1 at pci0 dev 19 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci1: applying AMD SB600/SB700 USB freeze workaround
ioapic0: int19
0x1a9c8<vector=0xc8,delmode=0x1,logical,actlo,level,masked,dest=0x0>
0x3000000<target=0x3>
ehci1: interrupting at ioapic0 pin 19, event channel 8
ehci1: dropped intr workaround enabled
ehci1: EHCI version 1.0
ehci1: companion controllers, 3 ports each: ohci2 ohci3
usb5 at ehci1: USB revision 2.0
vendor 0x1002 product 0x4385 (SMBus serial bus, revision 0x3a) at pci0 dev 20
function 0 not configured
ixpide1 at pci0 dev 20 function 1: ATI Technologies IXP IDE Controller (rev.
0x00)
ixpide1: bus-master DMA support present
ixpide1: primary channel configured to compatibility mode
ioapic0: int14 0x988<vector=0x88,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
ixpide1: primary channel interrupting at ioapic0 pin 14, event channel 9
atabus2 at ixpide1 channel 0
ixpide1: secondary channel configured to compatibility mode
ioapic0: int15 0x990<vector=0x90,delmode=0x1,logical,dest=0x0>
0x1000000<target=0x1>
ixpide1: secondary channel interrupting at ioapic0 pin 15, event channel 10
atabus3 at ixpide1 channel 1
hdaudio0 at pci0 dev 20 function 2: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 16, event channel 4
hdafg0 at hdaudio0: Realtek ALC888
hdafg0: DAC00 8ch: Speaker [Jack]
hdafg0: DAC01 2ch: HP Out [Jack]
hdafg0: DIG02 2ch: SPDIF Out [Jack]
hdafg0: ADC03 2ch: Line In [Jack], Mic In [Jack]
hdafg0: ADC04 2ch: Mic In [Jack]
hdafg0: DIG-In05 2ch: SPDIF In [Jack]
hdafg0: 8ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
audio0 at hdafg0: full duplex, playback, capture, independent
pcib0 at pci0 dev 20 function 3: vendor 0x1002 product 0x439d (rev. 0x00)
ppb2 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x00)
pci3 at ppb2 bus 3
ppb2: added to list as bus 3
pci3: i/o space, memory space enabled
ppb3 at pci3 dev 6 function 0: vendor 0x12d8 product 0xe111 (rev. 0x02)
ppb3: PCI Express 1.0 <PCI/PCI-X to PCI-E Bridge> x1 @ 2.5Gb/s
pci4 at ppb3 bus 4
ppb3: added to list as bus 4
pci4: i/o space, memory space enabled
vendor 0x1033 product 0x0194 (USB serial bus, interface 0x30, revision 0x04)
at pci4 dev 0 function 0 not configured
ohci4 at pci0 dev 20 function 5: vendor 0x1002 product 0x4399 (rev. 0x00)
ohci4: interrupting at ioapic0 pin 18, event channel 7
ohci4: OHCI version 1.0, legacy support
usb6 at ohci4: USB revision 1.0
pchb1 at pci0 dev 24 function 0: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb2 at pci0 dev 24 function 1: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb3 at pci0 dev 24 function 2: vendor 0x1022 product 0x1102 (rev. 0x00)
amdnb_misc0 at pci0 dev 24 function 3: AMD NB Misc Configuration
amdtemp0 at amdnb_misc0: AMD CPU Temperature Sensors (K8: core rev BH-G2,
socket AM2)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "xen_system_time" frequency 1000000000 Hz quality
10000
Xen clock: using event channel 11
xenbus0: using event channel 12
atapibus0 at atabus3: 2 targets
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
uhub2 at usb2: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
uhub3 at usb3: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 3 ports with 3 removable, self powered
uhub4 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 3 ports with 3 removable, self powered
uhub5 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 6 ports with 6 removable, self powered
uhub6 at usb6: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
cd0 at atapibus0 drive 1: <PIONEER DVD-RW DVR-110, EJTO028893WL, 8.22> cdrom
removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0 at atabus3 drive 0
wd0: <Maxtor 6L160P0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 152 GB, 317629 cyl, 16 head, 63 sec, 512 bytes/sect x 320170943 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(ixpide1:1:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
cd0(ixpide1:1:1): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
ehci0: handing over low speed device on port 1 to ohci0
crypto: assign driver 0, flags 2
crypto: driver 0 registers alg 1 flags 0 maxoplen 0
crypto: driver 0 registers alg 2 flags 0 maxoplen 0
crypto: driver 0 registers alg 3 flags 0 maxoplen 0
crypto: driver 0 registers alg 4 flags 0 maxoplen 0
crypto: driver 0 registers alg 5 flags 0 maxoplen 0
crypto: driver 0 registers alg 26 flags 0 maxoplen 0
crypto: driver 0 registers alg 27 flags 0 maxoplen 0
crypto: driver 0 registers alg 29 flags 0 maxoplen 0
crypto: driver 0 registers alg 33 flags 0 maxoplen 0
crypto: driver 0 registers alg 17 flags 0 maxoplen 0
crypto: driver 0 registers alg 6 flags 0 maxoplen 0
crypto: driver 0 registers alg 19 flags 0 maxoplen 0
crypto: driver 0 registers alg 7 flags 0 maxoplen 0
crypto: driver 0 registers alg 20 flags 0 maxoplen 0
crypto: driver 0 registers alg 15 flags 0 maxoplen 0
crypto: driver 0 registers alg 24 flags 0 maxoplen 0
crypto: driver 0 registers alg 25 flags 0 maxoplen 0
crypto: driver 0 registers alg 8 flags 0 maxoplen 0
crypto: driver 0 registers alg 21 flags 0 maxoplen 0
crypto: driver 0 registers alg 16 flags 0 maxoplen 0
crypto: driver 0 registers alg 9 flags 0 maxoplen 0
crypto: driver 0 registers alg 10 flags 0 maxoplen 0
crypto: driver 0 registers alg 13 flags 0 maxoplen 0
crypto: driver 0 registers alg 14 flags 0 maxoplen 0
crypto: driver 0 registers alg 28 flags 0 maxoplen 0
crypto: driver 0 registers alg 30 flags 0 maxoplen 0
crypto: driver 0 registers alg 31 flags 0 maxoplen 0
crypto: driver 0 registers alg 32 flags 0 maxoplen 0
crypto: driver 0 registers alg 11 flags 0 maxoplen 0
crypto: driver 0 registers alg 18 flags 0 maxoplen 0
crypto: driver 0 registers alg 23 flags 0 maxoplen 0
crypto: driver 0 registers alg 22 flags 0 maxoplen 0
Kernelized RAIDframe activated
boot device: wd0
root on wd0a dumps on wd0b
Your machine does not initialize mem_clusters; sparse_dumps disabled
root file system type: ffs
Enter pathname of shell or RETURN for /bin/sh: uhidev0 at uhub0 port 1
configuration 1 interface 0
uhidev0: vendor 0x05c7 Generic USB K/B, rev 1.10/0.01, addr 2, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd0 at ukbd0 mux 1
wskbd0: connecting to wsdisplay0
uhidev1 at uhub0 port 1 configuration 1 interface 1
uhidev1: vendor 0x05c7 Generic USB K/B, rev 1.10/0.01, addr 2, iclass 3/1
uhidev1: 3 report ids
ums0 at uhidev1 reportid 1: 3 buttons and Z dir
wsmouse0 at ums0 mux 0
uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=4, output=0, feature=0
#
--
t-hash
Home |
Main Index |
Thread Index |
Old Index