kern/44366: poweroff doesn't work

[mihai.chelaru%ngnetworks.ro@localhost]

>Number:         44366
>Category:       kern
>Synopsis:       ACPI poweroff doesn't work
>Confidential:   no
>Severity:       non-critical
>Priority:       medium
>Responsible:    kern-bug-people
>State:          open
>Class:          sw-bug
>Submitter-Id:   net
>Arrival-Date:   Mon Jan 10 11:50:00 +0000 2011
>Originator:     Mihai Chelaru
>Release:        NetBSD 5.99.43
>Organization:
        
>Environment:
        
        
System: NetBSD kefren.ngnetworks.ro 5.99.43 NetBSD 5.99.43 (Home) #49: Fri Jan 
7 10:09:44 EET 2011 
kefren%kefren.ngnetworks.ro@localhost:/disk3/work/netbsd-current/src/sys/arch/amd64/compile/obj/Home
 amd64
Architecture: x86_64
Machine: amd64
>Description:

poweroff doesn't work in -current on some computers. Affected computers
include:

        * Dell Mini 10 (i386) - the screen turns off but fans
        are still working and power led is still on.
        * custom made (amd64) Asus mainboard - see dmesg below -
        in most cases it shuts down the HDDs and it even turns
        off the front panel LEDs (including powerled), but power
        is not cut, fans are still spinning, the video card is still
        working so I can read the "acpi: entering state 5" message.
        This is the strangest one, because twice or thrice it
        completed the shutdown.

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.43 (Home) #49: Fri Jan  7 10:09:44 EET 2011
        
kefren%kefren.ngnetworks.ro@localhost:/disk3/work/netbsd-current/src/sys/arch/amd64/compile/obj/Home
total memory = 4095 MB
avail memory = 3952 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
System manufacturer P5Q-E (System Version)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2499MHz, id 0x10677
cpu1 at mainbus0 apid 1: Intel 686-class, 2499MHz, id 0x10677
cpu2 at mainbus0 apid 2: Intel 686-class, 2499MHz, id 0x10677
cpu3 at mainbus0 apid 3: Intel 686-class, 2499MHz, id 0x10677
ioapic0 at mainbus0 apid 4: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20100528
acpi0: X/RSDT: OemId <A_M_I_,OEMRSDT ,04000906>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
acpicpu0 at acpi0 (P001): ACPI CPU
ACPI Warning: Incorrect checksum in table [OEMB] - 0xF7, should be 0xEE 
(20100528/tbutils-354)
acpicpu1 at acpi0 (P002): ACPI CPU
acpicpu2 at acpi0 (P003): ACPI CPU
acpicpu3 at acpi0 (P004): ACPI CPU
MCH (PNP0C01) at acpi0 not configured
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
FDC (PNP0700) at acpi0 not configured
SIOR (PNP0C02) at acpi0 not configured
RMSC (PNP0C02) at acpi0 not configured
aibs0 at acpi0 (ASOC, ATK0110-16843024): ASUSTeK AI Booster
aibs0: V0: 0x06020000        Vcore Voltage   800 /  1600  0x1
aibs0: V1: 0x06020001         +3.3 Voltage  2970 /  3630  0x1
aibs0: V2: 0x06020002           +5 Voltage  4500 /  5500  0x1
aibs0: V3: 0x06020003          +12 Voltage 10200 / 13800  0x1
aibs0: T0: 0x06030000      CPU Temperature   600 /   950  0x10001
aibs0: T1: 0x06030001       MB Temperature   450 /   950  0x10001
aibs0: F0: 0x06040000        CPU FAN Speed   600 /  7200  0x10001
aibs0: F1: 0x06040001   CHASSIS1 FAN Speed   600 /  7200  0x10001
aibs0: F2: 0x06040002   CHASSIS2 FAN Speed   600 /  7200  0x10001
aibs0: F3: 0x06040003   CHASSIS3 FAN Speed   600 /  7200  0x10001
aibs0: F4: 0x06040004      POWER FAN Speed   600 /  7200  0x10001
hpet0 at acpi0 (HPET, PNP0103): mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
FWH (INT0800) at acpi0 not configured
FWHE (PNP0C02) at acpi0 not configured
UAR1 (PNP0501) at acpi0 not configured
OMSC (PNP0C02) at acpi0 not configured
PCIE (PNP0C02) at acpi0 not configured
RMEM (PNP0C01) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x8086 product 0x2e20 (rev. 0x02)
agp0 at pchb0: can't find internal VGA device config space
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x2e21 (rev. 0x02)
ppb0: unsupported PCI Express version
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci1 dev 0 function 0: vendor 0x1002 product 0x9598 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
radeondrm0 at vga0: ATI ATI Radeon HD 3600 XT
radeondrm0: Initialized radeon 1.29.0 20080613
hdaudio0 at pci1 dev 0 function 1: HD Audio Controller
hdaudio0: interrupting at ioapic0 pin 17
hdafg0 at hdaudio0: ATI RS600 HDMI
hdafg0: DAC00 2ch: Digital Out [Jack]
hdafg0: 2ch/0ch 48000Hz 16/16
audio0 at hdafg0: half duplex, playback
uhci0 at pci0 dev 26 function 0: vendor 0x8086 product 0x3a37 (rev. 0x00)
uhci0: interrupting at ioapic0 pin 16
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 26 function 1: vendor 0x8086 product 0x3a38 (rev. 0x00)
uhci1: interrupting at ioapic0 pin 21
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 26 function 2: vendor 0x8086 product 0x3a39 (rev. 0x00)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 26 function 7: vendor 0x8086 product 0x3a3c (rev. 0x00)
ehci0: interrupting at ioapic0 pin 18
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
hdaudio1 at pci0 dev 27 function 0: HD Audio Controller
hdaudio1: interrupting at ioapic0 pin 22
hdafg1 at hdaudio1: ADI AD1989B
hdafg1: DAC00 8ch: Speaker [Jack]
hdafg1: ADC01 2ch: CD [Built-In], Line In [Jack], Mic In [Jack]
hdafg1: DAC02 2ch: HP Out [Jack]
hdafg1: DAC03 2ch: SPDIF Out [Jack]
hdafg1: DAC04 2ch: Digital Out [Jack]
hdafg1: 8ch/2ch 8000Hz 11025Hz 16000Hz 22050Hz 32000Hz 44100Hz 48000Hz 88200Hz 
96000Hz 192000Hz 16/16 20/32 24/32
audio1 at hdafg1: full duplex, playback, capture, independent
ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x3a40 (rev. 0x00)
pci2 at ppb1 bus 4
pci2: memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 28 function 4: vendor 0x8086 product 0x3a48 (rev. 0x00)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ahcisata0 at pci3 dev 0 function 0: vendor 0x11ab product 0x6121
ahcisata0: interrupting at ioapic0 pin 16
ahcisata0: 64-bit DMA
ahcisata0: AHCI revision 1.0, 3 ports, 32 command slots, features 0xca226000
atabus0 at ahcisata0 channel 0
atabus1 at ahcisata0 channel 1
atabus2 at ahcisata0 channel 2
ppb3 at pci0 dev 28 function 5: vendor 0x8086 product 0x3a4a (rev. 0x00)
pci4 at ppb3 bus 2
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
mskc0 at pci4 dev 0 function 0, Yukon-2 EC Ultra rev. B0 (0x3): ioapic0 pin 17
msk0 at mskc0 port A: Ethernet address 00:22:15:80:9f:02
makphy0 at msk0 phy 0: Marvell 88E1149 Gigabit PHY, rev. 1
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
uhci3 at pci0 dev 29 function 0: vendor 0x8086 product 0x3a34 (rev. 0x00)
uhci3: interrupting at ioapic0 pin 23
usb4 at uhci3: USB revision 1.0
uhci4 at pci0 dev 29 function 1: vendor 0x8086 product 0x3a35 (rev. 0x00)
uhci4: interrupting at ioapic0 pin 19
usb5 at uhci4: USB revision 1.0
uhci5 at pci0 dev 29 function 2: vendor 0x8086 product 0x3a36 (rev. 0x00)
uhci5: interrupting at ioapic0 pin 18
usb6 at uhci5: USB revision 1.0
ehci1 at pci0 dev 29 function 7: vendor 0x8086 product 0x3a3a (rev. 0x00)
ehci1: interrupting at ioapic0 pin 23
ehci1: EHCI version 1.0
ehci1: companion controllers, 2 ports each: uhci3 uhci4 uhci5
usb7 at ehci1: USB revision 2.0
ppb4 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0x90)
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled
clcs0 at pci5 dev 0 function 0: vendor 0x1013 product 0x6003 (rev. 0x01)
clcs0: interrupting at ioapic0 pin 16
clcs0: ac97: Crystal CS4294 codec; headphone, 20 bit DAC, 18 bit ADC, Crystal 
Semi 3D
audio2 at clcs0: full duplex, playback, capture, independent
midi1 at clcs0: CS4280 MIDI UART
skc0 at pci5 dev 2 function 0: ioapic0 pin 18
skc0: interrupt moderation is 0 us
skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
sk0 at skc0 port A: Ethernet address 00:22:15:80:ac:e8
makphy1 at sk0 phy 0: Marvell 88E1011 Gigabit PHY, rev. 5
makphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
pcib0 at pci0 dev 31 function 0: vendor 0x8086 product 0x3a16 (rev. 0x00)
piixide0 at pci0 dev 31 function 2: Intel 82801JI Serial ATA Controller (ICH10) 
(rev. 0x00)
piixide0: bus-master DMA support present
piixide0: primary channel configured to native-PCI mode
piixide0: using ioapic0 pin 19 for native-PCI interrupt
atabus3 at piixide0 channel 0
piixide0: secondary channel configured to native-PCI mode
atabus4 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x3a30 (rev. 0x00)
ichsmb0: interrupting at ioapic0 pin 18
iic0 at ichsmb0: I2C bus
spdmem0 at iic0 addr 0x52
spdmem0: DDR2 SDRAM, no parity or ECC, 2GB, 800MHz (PC2-6400)
spdmem0: 14 rows, 10 cols, 2 ranks, 8 banks/chip, 2.50ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 5-5-5-18
spdmem0: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
piixide1 at pci0 dev 31 function 5: Intel 82801JI Serial ATA Controller (ICH10) 
(rev. 0x00)
piixide1: bus-master DMA support present
piixide1: primary channel wired to native-PCI mode
piixide1: using ioapic0 pin 19 for native-PCI interrupt
atabus5 at piixide1 channel 0
piixide1: secondary channel wired to native-PCI mode
atabus6 at piixide1 channel 1
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
uhub4 at usb4: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 2 ports with 2 removable, self powered
uhub6 at usb6: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
IPsec: Initialized Security Association Processing.
uhub7 at usb7: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub7: 6 ports with 6 removable, self powered
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
wd0 at atabus3 drive 0: <ST3320620AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd1 at atabus3 drive 1: <WDC WD5000AAJS-00YFA0>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd1(piixide0:0:1): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd2 at atabus4 drive 1: <WDC WD1001FALS-00J7B0>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors
wd2: 32-bit data port
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd2(piixide0:1:1): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio3 at pad0: half duplex, playback, capture
boot device: wd2
root on wd2e dumps on wd1b
root file system type: ffs
uhidev0 at uhub0 port 1 configuration 1 interface 0
uhidev0: Logitech USB Receiver, rev 2.00/5.00, addr 2, iclass 3/1
ums0 at uhidev0: 16 buttons, W and Z dirs
wsmouse0 at ums0 mux 0
uhidev1 at uhub0 port 1 configuration 1 interface 1
uhidev1: Logitech USB Receiver, rev 2.00/5.00, addr 2, iclass 3/0
uhidev1: 17 report ids
uhid0 at uhidev1 reportid 3: input=4, output=0, feature=0
uhid1 at uhidev1 reportid 16: input=6, output=6, feature=0
uhid2 at uhidev1 reportid 17: input=19, output=19, feature=0
uhidev2 at uhub1 port 1 configuration 1 interface 0
uhidev2: Logitech Logitech Illuminated Keyboard, rev 2.00/55.00, addr 2, iclass 
3/1
ukbd0 at uhidev2
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev3 at uhub1 port 1 configuration 1 interface 1
uhidev3: Logitech Logitech Illuminated Keyboard, rev 2.00/55.00, addr 2, iclass 
3/0
uhidev3: 16 report ids
uhid3 at uhidev3 reportid 3: input=7, output=0, feature=0
uhid4 at uhidev3 reportid 16: input=6, output=6, feature=0
skc0: interrupt moderation is 1000 us
uhub4: device problem, disabling port 2
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x25, vt100 emulation)
wsdisplay0: screen 6 added (80x25, vt100 emulation)
wsdisplay0: screen 7 added (80x25, vt100 emulation)
info: [drm] Setting GART location based on new memory map
info: [drm] Loading RV635 Microcode
info: [drm] Resetting GPU
info: [drm] writeback test succeeded in 1 usecs
wd2: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors
wd2: 32-bit data port
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd2(piixide0:1:1): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio3 at pad0: half duplex, playback, capture
boot device: wd2
root on wd2e dumps on wd1b
root file system type: ffs
uhidev0 at uhub0 port 1 configuration 1 interface 0
uhidev0: Logitech USB Receiver, rev 2.00/5.00, addr 2, iclass 3/1
ums0 at uhidev0: 16 buttons, W and Z dirs
wsmouse0 at ums0 mux 0
uhidev1 at uhub0 port 1 configuration 1 interface 1
uhidev1: Logitech USB Receiver, rev 2.00/5.00, addr 2, iclass 3/0
uhidev1: 17 report ids
uhid0 at uhidev1 reportid 3: input=4, output=0, feature=0
uhid1 at uhidev1 reportid 16: input=6, output=6, feature=0
uhid2 at uhidev1 reportid 17: input=19, output=19, feature=0
uhidev2 at uhub1 port 1 configuration 1 interface 0
uhidev2: Logitech Logitech Illuminated Keyboard, rev 2.00/55.00, addr 2, iclass 
3/1
ukbd0 at uhidev2
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev3 at uhub1 port 1 configuration 1 interface 1
uhidev3: Logitech Logitech Illuminated Keyboard, rev 2.00/55.00, addr 2, iclass 
3/0
uhidev3: 16 report ids
uhid3 at uhidev3 reportid 3: input=7, output=0, feature=0
uhid4 at uhidev3 reportid 16: input=6, output=6, feature=0
skc0: interrupt moderation is 1000 us
uhub4: device problem, disabling port 2
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsdisplay0: screen 5 added (80x25, vt100 emulation)
wsdisplay0: screen 6 added (80x25, vt100 emulation)
wsdisplay0: screen 7 added (80x25, vt100 emulation)
info: [drm] Setting GART location based on new memory map
info: [drm] Loading RV635 Microcode
info: [drm] Resetting GPU
info: [drm] writeback test succeeded in 1 usecs
radeondrm0: interrupting at ioapic0 pin 16


>How-To-Repeat:
        
>Fix:
        

>Unformatted: