Re: kern/37826 (Kernel sees only one SATA channel (out of four) on Abit AN52 motherboard (nvidia nf520__single chip))

[Art <develunix%gmail.com@localhost>]

The following reply was made to PR kern/37826; it has been noted by GNATS.

From: Art <develunix%gmail.com@localhost>
To: gnats-bugs%NetBSD.org@localhost
Cc: kern-bug-people%netbsd.org@localhost, netbsd-bugs%netbsd.org@localhost, 
dholland%NetBSD.org@localhost
Subject: Re: kern/37826 (Kernel sees only one SATA channel (out of four) on
        Abit AN52 motherboard (nvidia nf520__single chip))
Date: Thu, 26 Feb 2009 06:20:17 -0700

 On Thu, 2009-02-26 at 05:30 -0700, Art wrote:
 > On Sun, 2009-02-22 at 06:42 +0000, dholland%NetBSD.org@localhost wrote:
 > > Synopsis: Kernel sees only one SATA channel (out of four) on Abit AN52 
 > > motherboard (nvidia nf520__single chip)
 > > 
 > > State-Changed-From-To: open->feedback
 > > State-Changed-By: dholland%NetBSD.org@localhost
 > > State-Changed-When: Sun, 22 Feb 2009 06:42:10 +0000
 > > State-Changed-Why:
 > > This should be fixed in current and 5.0; the controller should attach as
 > > ahcisata rather than viaide regardless of BIOS setting.
 > > 
 > > Does it?
 
   Maybe it doesn't after all. I'm sorry about the premature
 announcement. It appears that it's attaching as pciide, although it
 is seeing both drives (one on the first interface and the other on
 the third). I'll make a 5.0RC2, i386 install disk with a GENERIC
 kernel and try that as soon as possible.
 
 >   It appears that it does! See wd1, below. The following resulted after
 > I commented the "viaide*" line out in the GENERIC kernel
 > configuration file and recompiled. The rest of the configuration file is
 > original as issued. I might try a fresh amd64 install and update to
 > 5.0RC2 (amd64) with that now, to see if it works.  ;-)
 > 
 > ================
 > 
 > Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004,
 > 2005,
 >    2006, 2007, 2008
 >    The NetBSD Foundation, Inc.  All rights reserved.
 > Copyright (c) 1982, 1986, 1989, 1991, 1993
 >    The Regents of the University of California.  All rights reserved.
 > 
 > NetBSD 5.0_RC2 (GENERIC) #0: Thu Feb 26 03:53:42 MST 2009
 >        elijah@noah:/usr/obj/sys/arch/i386/compile/GENERIC
 > total memory = 2046 MB
 > avail memory = 1999 MB
 > timecounter: Timecounters tick every 10.000 msec
 > timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
 > Unknow Unknow (Unknow)
 > mainbus0 (root)
 > cpu0 at mainbus0 apid 0: AMD 686-class, 2109MHz, id 0x60fb1
 > cpu0: AMD PowerNow! Technology 2100 MHz
 > cpu0: available frequencies (Mhz): 1000 1800 2000 2100
 > cpu1 at mainbus0 apid 1: AMD 686-class, 2109MHz, id 0x60fb1
 > ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 11, 24 pins
 > acpi0 at mainbus0: Intel ACPICA 20080321
 > acpi0: X/RSDT: OemId <Nvidia,NVDAACPI,42302e31>, AslId <NVDA,00000000>
 > acpi0: SCI interrupting at int 9
 > acpi0: fixed-feature power button present
 > timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
 > ACPI-Fast 24-bit timer
 > acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
 > attimer1 at acpi0 (TMR, PNP0100): AT Timer
 > attimer1: io 0x40-0x43
 > hpet0 at acpi0 (HPET, PNP0103)
 > hpet0: mem 0xfeff0000-0xfeff03ff irq 0,8
 > timecounter: Timecounter "hpet0" frequency 25000000 Hz quality 2000
 > pcppi1 at acpi0 (SPKR, PNP0800)
 > pcppi1: io 0x61
 > midi0 at pcppi1: PC speaker (CPU-intensive output)
 > sysbeep0 at pcppi1
 > npx1 at acpi0 (COPR, PNP0C04)
 > npx1: io 0xf0-0xff irq 13
 > npx1: reported by CPUID; using exception 16
 > FDC0 (PNP0700) at acpi0 not configured
 > UAR1 (PNP0501) at acpi0 not configured
 > pckbc1 at acpi0 (PS2M, PNP0F13): aux port
 > pckbc1: irq 12
 > pckbc2 at acpi0 (PS2K, PNP0303): kbd port
 > pckbc2: io 0x60,0x64 irq 1
 > FAN (PNP0C0B) at acpi0 not configured
 > acpitz0 at acpi0 (THRM): active cooling level 0: 48.0C critical 60.0C
 > passive 42.0C
 > apm0 at acpi0: Power Management spec V1.2
 > attimer1: attached to pcppi1
 > pckbd0 at pckbc2 (kbd slot)
 > pckbc2: using irq 1 for kbd slot
 > wskbd0 at pckbd0: console keyboard
 > pms0 at pckbc2 (aux slot)
 > pckbc2: using irq 12 for aux slot
 > wsmouse0 at pms0 mux 0
 > pci0 at mainbus0 bus 0: configuration mode 1
 > pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
 > vendor 0x10de product 0x0444 (RAM memory, revision 0xa3) at pci0 dev 0
 > function 0 not configured
 > pcib0 at pci0 dev 1 function 0
 > pcib0: vendor 0x10de product 0x0441 (rev. 0xa3)
 > nfsmbc0 at pci0 dev 1 function 1: vendor 0x10de product 0x0446 (rev.
 > 0xa1)
 > nfsmb0 at nfsmbc0 SMBus 1
 > iic0 at nfsmb0: I2C bus
 > nfsmb1 at nfsmbc0 SMBus 2
 > iic1 at nfsmb1: I2C bus
 > vendor 0x10de product 0x0445 (RAM memory, revision 0xa1) at pci0 dev 1
 > function 2 not configured
 > ohci0 at pci0 dev 2 function 0: vendor 0x10de product 0x0454 (rev. 0xa3)
 > AUBA: Picked IRQ 20 with weight 0
 > ohci0: interrupting at ioapic0 pin 20
 > ohci0: OHCI version 1.0, legacy support
 > usb0 at ohci0: USB revision 1.0
 > ehci0 at pci0 dev 2 function 1: vendor 0x10de product 0x0455 (rev. 0xa3)
 > AUB2: Picked IRQ 21 with weight 0
 > ehci0: interrupting at ioapic0 pin 21
 > ehci0: EHCI version 1.0
 > ehci0: companion controller, 10 ports each: ohci0
 > usb1 at ehci0: USB revision 2.0
 > azalia0 at pci0 dev 7 function 0: Generic High Definition Audio
 > Controller
 > AAZA: Picked IRQ 22 with weight 0
 > azalia0: interrupting at ioapic0 pin 22
 > azalia0: host: 0x10de/0x044a (rev. 161), HDA rev. 1.0
 > ppb0 at pci0 dev 8 function 0: vendor 0x10de product 0x0449 (rev. 0xa1)
 > pci1 at ppb0 bus 1
 > pci1: i/o space, memory space enabled
 > bktr0 at pci1 dev 10 function 0
 > APC3: Picked IRQ 18 with weight 0
 > bktr0: interrupting at ioapic0 pin 18
 > bktr0: Warning - card vendor 0x0000 (model 0x0000) unknown.
 > bktr0: Detected a DPL34-1@-@0 at 0x84
 > bktr0: Intel Smart Video III/VideoLogic Captivator PCI, <no> tuner,
 > dpl3518a dolby.
 > vendor 0x109e product 0x0878 (miscellaneous multimedia, revision 0x11)
 > at pci1 dev 10 function 1 not configured
 > pciide0 at pci0 dev 9 function 0
 > pciide0: vendor 0x10de product 0x0448 (rev. 0xa1)
 > pciide0: bus-master DMA support present, but unused (no driver support)
 > pciide0: primary channel configured to compatibility mode
 > pciide0: primary channel interrupting at ioapic0 pin 14
 > atabus0 at pciide0 channel 0
 > pciide0: secondary channel configured to compatibility mode
 > pciide0: secondary channel ignored (not responding; disabled or no
 > drives?)
 > pciide1 at pci0 dev 10 function 0
 > pciide1: vendor 0x10de product 0x045d (rev. 0xa3)
 > pciide1: bus-master DMA support present, but unused (no driver support)
 > pciide1: primary channel wired to native-PCI mode
 > APSI: Picked IRQ 23 with weight 0
 > pciide1: using ioapic0 pin 23 for native-PCI interrupt
 > atabus1 at pciide1 channel 0
 > pciide1: secondary channel wired to native-PCI mode
 > atabus2 at pciide1 channel 1
 > ppb1 at pci0 dev 11 function 0: vendor 0x10de product 0x045b (rev. 0xa1)
 > pci2 at ppb1 bus 2
 > pci2: i/o space, memory space enabled, rd/line, wr/inv ok
 > mskc0 at pci2 dev 0 function 0APC6: Picked IRQ 16 with weight 0
 > mskc0: interrupt moderation is 0 us
 > , Yukon-2 EC Ultra rev. B0 (0x3): ioapic0 pin 16
 > msk0 at mskc0 port A: Ethernet address 00:50:8d:b0:b4:ef
 > ukphy0 at msk0 phy 0: Generic IEEE 802.3u media interface
 > ukphy0: OUI 0x000ac2, model 0x000b, rev. 1
 > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
 > 1000baseT-FDX, auto
 > ppb2 at pci0 dev 12 function 0: vendor 0x10de product 0x045a (rev. 0xa1)
 > pci3 at ppb2 bus 3
 > pci3: i/o space, memory space enabled, rd/line, wr/inv ok
 > ppb3 at pci0 dev 13 function 0: vendor 0x10de product 0x0458 (rev. 0xa1)
 > pci4 at ppb3 bus 4
 > pci4: i/o space, memory space enabled, rd/line, wr/inv ok
 > vga1 at pci4 dev 0 function 0: vendor 0x1002 product 0x5b62 (rev. 0x00)
 > vga1: WARNING: ignoring 64-bit BAR @ 0x10
 > vga1: WARNING: ignoring 64-bit BAR @ 0x18
 > wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using
 > wskbd0
 > wsmux1: connecting to wsdisplay0
 > drm at vga1 not configured
 > vendor 0x1002 product 0x5b72 (miscellaneous display) at pci4 dev 0
 > function 1 not configured
 > ppb4 at pci0 dev 14 function 0: vendor 0x10de product 0x0459 (rev. 0xa1)
 > pci5 at ppb4 bus 5
 > pci5: i/o space, memory space enabled, rd/line, wr/inv ok
 > pchb0 at pci0 dev 24 function 0
 > pchb0: vendor 0x1022 product 0x1100 (rev. 0x00)
 > pchb1 at pci0 dev 24 function 1
 > pchb1: vendor 0x1022 product 0x1101 (rev. 0x00)
 > pchb2 at pci0 dev 24 function 2
 > pchb2: vendor 0x1022 product 0x1102 (rev. 0x00)
 > amdtemp0 at pci0 dev 24 function 3
 > amdtemp0: AMD CPU Temperature Sensors (K8: core rev BH-G1, socket AM2)
 > isa0 at pcib0
 > com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
 > fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
 > timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
 > azalia0: codec[0]: Realtek ALC883 (rev. 0.2), HDA rev. 1.0
 > audio0 at azalia0: full duplex, independent
 > atapibus0 at atabus0: 2 targets
 > uhub0 at usb0: vendor 0x10de OHCI root hub, class 9/0, rev 1.00/1.00,
 > addr 1
 > uhub0: 10 ports with 10 removable, self powered
 > uhub1 at usb1: vendor 0x10de EHCI root hub, class 9/0, rev 2.00/1.00,
 > addr 1
 > uhub1: 10 ports with 10 removable, self powered
 > cd0 at atapibus0 drive 0: <LITE-ON DVDRW SOHW-1673S, , JS07> cdrom
 > removable
 > cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
 > wd0 at atabus1 drive 0: <HDS728080PLA380>
 > wd0: drive supports 16-sector PIO transfers, LBA48 addressing
 > wd0: 78533 MB, 159560 cyl, 16 head, 63 sec, 512 bytes/sect x 160836480
 > sectors
 > wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
 > wd1 at atabus2 drive 0: <HDS728080PLA380>
 > wd1: drive supports 16-sector PIO transfers, LBA48 addressing
 > wd1: 78533 MB, 159560 cyl, 16 head, 63 sec, 512 bytes/sect x 160836480
 > sectors
 > wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
 > Kernelized RAIDframe activated
 > pad0: outputs: 44100Hz, 16-bit, stereo
 > audio1 at pad0: half duplex
 > raid0: RAID Level 1
 > raid0: Components: /dev/wd0a component1[**FAILED**]
 > raid0: Total Sectors: 160836096 (78533 MB)
 > boot device: raid0
 > root on raid0a dumps on raid0b
 > root file system type: ffs
 > mskc0: interrupt moderation is 1000 us
 > wsdisplay0: screen 1 added (80x25, vt100 emulation)
 > wsdisplay0: screen 2 added (80x25, vt100 emulation)
 > wsdisplay0: screen 3 added (80x25, vt100 emulation)
 > wsdisplay0: screen 4 added (80x25, vt100 emulation)
 > raid0: Error re-writing parity!
 > 
 >