Current-Users archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index][Old Index]
HP DL380p Gen8 interrupt storm
Hi,
one machine I'm testing NetBSD on feels sort of sluggish, which
is strange because it's got lots of RAM (128GB) and a pair of
Xeon(R) CPU E5-2650 CPUs, for a total of 16 physical cores and 32
with hyperthreading.
It looks like one of the CPUs is using most of its time doing
interrupt processing, "systat vm" often shows ***** in "Intr" and
I have a constant buzz of 6.3% System CPU:
Proc:r d s Csw Traps SysCal Intr Soft Fault PAGING SWAPPING
1 7 557 281 355 ***** 64 277 in out in out
ops
6.3% Sy 0.0% Us 0.0% Ni 0.1% In 93.6% Id pages
| | | | | | | | | | |
=== 2 forks
2 fkppw
Checking further:
stest: {8} vmstat -i
interrupt total rate
TLB shootdown 4677209 0
cpu0 timer 1046424629 99
msix2 vec 0 62702425 5
msix6 vec 0 3294854 0
ioapic0 pin 21 84 0
ioapic0 pin 20 21074226 2
ioapic0 pin 17 3344590700017 319462
ioapic0 pin 4 12722 0
Total 3345728886166 319570
stest: {9} grep 'ioapic0 pin 17' /var/run/dmesg.boot
pciide0: using ioapic0 pin 17 for native-PCI interrupt
stest: {10}
pciide0 only has the built-in CD drive, if I see correctly.
Full dmesg attached below.
Any hints about what's going on and how to further diagnose and
eventually cure it?
Regards,
- Håvard
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017,
2018, 2019, 2020, 2021 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 9.99.81 (GENERIC) #2: Wed May 5 11:59:20 UTC 2021
he%stest.urc.uninett.no@localhost:/usr/obj/sys/arch/amd64/compile/GENERIC
total memory = 127 GB
avail memory = 123 GB
entropy: entering seed from bootloader with 256 bits of entropy
entropy: ready
timecounter: Timecounters tick every 10.000 msec
Kernelized RAIDframe activated
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
HP ProLiant DL380p Gen8
mainbus0 (root)
ACPI: RSDP 0x00000000000F4F00 000024 (v02 HP )
ACPI: XSDT 0x00000000BDDAED00 0000EC (v01 HP ProLiant 00000002 ?? 0000162E)
ACPI: FACP 0x00000000BDDAEE40 0000F4 (v03 HP ProLiant 00000002 ?? 0000162E)
Firmware Warning (ACPI): Invalid length for FADT/Pm1aControlBlock: 32, using default 16 (20210331/tbfadt-742)
Firmware Warning (ACPI): Invalid length for FADT/Pm2ControlBlock: 32, using default 8 (20210331/tbfadt-742)
ACPI: DSDT 0x00000000BDDAEF40 0026DC (v01 HP DSDT 00000001 INTL 20030228)
ACPI: FACS 0x00000000BDDAC140 000040
ACPI: SPCR 0x00000000BDDAC180 000050 (v01 HP SPCRRBSU 00000001 ?? 0000162E)
ACPI: MCFG 0x00000000BDDAC200 00003C (v01 HP ProLiant 00000001 00000000)
ACPI: HPET 0x00000000BDDAC240 000038 (v01 HP ProLiant 00000002 ?? 0000162E)
ACPI: FFFF 0x00000000BDDAC280 000064 (v02 HP ProLiant 00000002 ?? 0000162E)
ACPI: SPMI 0x00000000BDDAC300 000040 (v05 HP ProLiant 00000001 ?? 0000162E)
ACPI: FFFF 0x00000000BDDAC340 000230 (v01 HP ProLiant 00000001 ?? 0000162E)
ACPI: APIC 0x00000000BDDAC580 00026A (v01 HP ProLiant 00000002 00000000)
ACPI: SRAT 0x00000000BDDAC800 000750 (v01 HP Proliant 00000001 ?? 0000162E)
ACPI: FFFF 0x00000000BDDACF80 000176 (v01 HP ProLiant 00000001 ?? 0000162E)
ACPI: FFFF 0x00000000BDDAD100 000030 (v01 HP ProLiant 00000001 ?? 0000162E)
ACPI: FFFF 0x00000000BDDAD140 0000BC (v01 HP ProLiant 00000001 ?? 0000162E)
ACPI: DMAR 0x00000000BDDAD200 000558 (v01 HP ProLiant 00000001 ?? 0000162E)
ACPI: FFFF 0x00000000BDDAEC40 000030 (v01 HP ProLiant 00000001 00000000)
ACPI: PCCT 0x00000000BDDAEC80 00006E (v01 HP Proliant 00000001 PH 0000504D)
ACPI: SSDT 0x00000000BDDB1640 0007EA (v01 HP DEV_PCI1 00000001 INTL 20120503)
ACPI: SSDT 0x00000000BDDB1E40 000103 (v03 HP CRSPCI0 00000002 HP 00000001)
ACPI: SSDT 0x00000000BDDB1F80 000098 (v03 HP CRSPCI1 00000002 HP 00000001)
ACPI: SSDT 0x00000000BDDB2040 00038A (v02 HP riser0 00000002 INTL 20030228)
ACPI: SSDT 0x00000000BDDB2400 000536 (v03 HP riser1a 00000002 INTL 20030228)
ACPI: SSDT 0x00000000BDDB2940 000537 (v03 HP riser2a 00000002 INTL 20030228)
ACPI: SSDT 0x00000000BDDB2E80 000BB9 (v01 HP pcc 00000001 INTL 20120503)
ACPI: SSDT 0x00000000BDDB3A40 000377 (v01 HP pmab 00000001 INTL 20120503)
ACPI: SSDT 0x00000000BDDB3DC0 005524 (v01 HP pcc2 00000001 INTL 20120503)
ACPI: SSDT 0x00000000BDDB9300 004604 (v01 INTEL PPM RCM 00000001 INTL 20061109)
ACPI: 11 ACPI AML tables successfully acquired and loaded
ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 0x20, 24 pins
ioapic1 at mainbus0 apid 0: pa 0xfec10000, version 0x20, 24 pins
ioapic2 at mainbus0 apid 10: pa 0xfec40000, version 0x20, 24 pins
x2APIC available but disabled by DMAR table
cpu0 at mainbus0 apid 0
cpu0: Use lfence to serialize rdtsc
cpu0: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu0: node 0, package 0, core 0, smt 0
cpu1 at mainbus0 apid 2
cpu1: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu1: node 0, package 0, core 1, smt 0
cpu2 at mainbus0 apid 4
cpu2: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu2: node 0, package 0, core 2, smt 0
cpu3 at mainbus0 apid 6
cpu3: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu3: node 0, package 0, core 3, smt 0
cpu4 at mainbus0 apid 8
cpu4: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu4: node 0, package 0, core 4, smt 0
cpu5 at mainbus0 apid 10
cpu5: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu5: node 0, package 0, core 5, smt 0
cpu6 at mainbus0 apid 12
cpu6: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu6: node 0, package 0, core 6, smt 0
cpu7 at mainbus0 apid 14
cpu7: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu7: node 0, package 0, core 7, smt 0
cpu8 at mainbus0 apid 32
cpu8: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu8: node 1, package 1, core 0, smt 0
cpu9 at mainbus0 apid 34
cpu9: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu9: node 1, package 1, core 1, smt 0
cpu10 at mainbus0 apid 36
cpu10: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu10: node 1, package 1, core 2, smt 0
cpu11 at mainbus0 apid 38
cpu11: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu11: node 1, package 1, core 3, smt 0
cpu12 at mainbus0 apid 40
cpu12: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu12: node 1, package 1, core 4, smt 0
cpu13 at mainbus0 apid 42
cpu13: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu13: node 1, package 1, core 5, smt 0
cpu14 at mainbus0 apid 44
cpu14: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu14: node 1, package 1, core 6, smt 0
cpu15 at mainbus0 apid 46
cpu15: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu15: node 1, package 1, core 7, smt 0
cpu16 at mainbus0 apid 1
cpu16: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu16: node 0, package 0, core 0, smt 1
cpu17 at mainbus0 apid 3
cpu17: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu17: node 0, package 0, core 1, smt 1
cpu18 at mainbus0 apid 5
cpu18: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu18: node 0, package 0, core 2, smt 1
cpu19 at mainbus0 apid 7
cpu19: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu19: node 0, package 0, core 3, smt 1
cpu20 at mainbus0 apid 9
cpu20: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu20: node 0, package 0, core 4, smt 1
cpu21 at mainbus0 apid 11
cpu21: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu21: node 0, package 0, core 5, smt 1
cpu22 at mainbus0 apid 13
cpu22: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu22: node 0, package 0, core 6, smt 1
cpu23 at mainbus0 apid 15
cpu23: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu23: node 0, package 0, core 7, smt 1
cpu24 at mainbus0 apid 33
cpu24: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu24: node 1, package 1, core 0, smt 1
cpu25 at mainbus0 apid 35
cpu25: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu25: node 1, package 1, core 1, smt 1
cpu26 at mainbus0 apid 37
cpu26: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu26: node 1, package 1, core 2, smt 1
cpu27 at mainbus0 apid 39
cpu27: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu27: node 1, package 1, core 3, smt 1
cpu28 at mainbus0 apid 41
cpu28: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu28: node 1, package 1, core 4, smt 1
cpu29 at mainbus0 apid 43
cpu29: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu29: node 1, package 1, core 5, smt 1
cpu30 at mainbus0 apid 45
cpu30: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu30: node 1, package 1, core 6, smt 1
cpu31 at mainbus0 apid 47
cpu31: Intel(R) Xeon(R) CPU E5-2650 0 @ 2.00GHz, id 0x206d7
cpu31: node 1, package 1, core 7, smt 1
acpi0 at mainbus0: Intel ACPICA 20210331
acpi0: X/RSDT: OemId <HP ,ProLiant,00000002>, AslId < <2147483602>^D,0000162e>
acpi0: MCFG: segment 0, bus 0-255, address 0x00000000c0000000
acpi0: SCI interrupting at int 9
acpi0: fixed power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
ipmi_acpi0 at acpi0 (MI0, IPI0001-0): io 0xca2-0xca3
ipmi0 at ipmi_acpi0
attimer1 at acpi0 (TIME, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (BEEP, PNP0800): io 0x61
spkr0 at pcppi1: PC Speaker
wsbell at spkr0 not configured
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
COMA (PNP0501) at acpi0 not configured
pckbc1 at acpi0 (KBD, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (PS2M, PNP0F13) (aux port): irq 12
PMI0 (ACPI000D) at acpi0 not configured
acpitz0 at acpi0 (THM0): cpu0
acpitz0: levels: critical 31.3 C, passive 9.8 C, passive cooling
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0 mux 1
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: Intel E5 Host (rev. 0x07)
ppb0 at pci0 dev 1 function 0: Intel E5 PCIe x8 or x4 (rev. 0x07)
ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x8 @ 8.0GT/s
ppb0: link is x8 @ 5.0GT/s
pci1 at ppb0 bus 7
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ixg0 at pci1 dev 0 function 0: Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 4.0.1-k
ixg0: clearing prefetchable bit
ixg0: device 82599EB
ixg0: ETrackID 80000208
ixg0: for TX/RX, interrupting at msix0 vec 0, bound queue 0 to cpu 0
ixg0: for TX/RX, interrupting at msix0 vec 1, bound queue 1 to cpu 1
ixg0: for TX/RX, interrupting at msix0 vec 2, bound queue 2 to cpu 2
ixg0: for TX/RX, interrupting at msix0 vec 3, bound queue 3 to cpu 3
ixg0: for TX/RX, interrupting at msix0 vec 4, bound queue 4 to cpu 4
ixg0: for TX/RX, interrupting at msix0 vec 5, bound queue 5 to cpu 5
ixg0: for TX/RX, interrupting at msix0 vec 6, bound queue 6 to cpu 6
ixg0: for TX/RX, interrupting at msix0 vec 7, bound queue 7 to cpu 7
ixg0: for TX/RX, interrupting at msix0 vec 8, bound queue 8 to cpu 8
ixg0: for TX/RX, interrupting at msix0 vec 9, bound queue 9 to cpu 9
ixg0: for TX/RX, interrupting at msix0 vec 10, bound queue 10 to cpu 10
ixg0: for TX/RX, interrupting at msix0 vec 11, bound queue 11 to cpu 11
ixg0: for TX/RX, interrupting at msix0 vec 12, bound queue 12 to cpu 12
ixg0: for TX/RX, interrupting at msix0 vec 13, bound queue 13 to cpu 13
ixg0: for TX/RX, interrupting at msix0 vec 14, bound queue 14 to cpu 14
ixg0: for TX/RX, interrupting at msix0 vec 15, bound queue 15 to cpu 15
ixg0: for TX/RX, interrupting at msix0 vec 16, bound queue 16 to cpu 16
ixg0: for TX/RX, interrupting at msix0 vec 17, bound queue 17 to cpu 17
ixg0: for TX/RX, interrupting at msix0 vec 18, bound queue 18 to cpu 18
ixg0: for TX/RX, interrupting at msix0 vec 19, bound queue 19 to cpu 19
ixg0: for TX/RX, interrupting at msix0 vec 20, bound queue 20 to cpu 20
ixg0: for TX/RX, interrupting at msix0 vec 21, bound queue 21 to cpu 21
ixg0: for TX/RX, interrupting at msix0 vec 22, bound queue 22 to cpu 22
ixg0: for TX/RX, interrupting at msix0 vec 23, bound queue 23 to cpu 23
ixg0: for TX/RX, interrupting at msix0 vec 24, bound queue 24 to cpu 24
ixg0: for TX/RX, interrupting at msix0 vec 25, bound queue 25 to cpu 25
ixg0: for TX/RX, interrupting at msix0 vec 26, bound queue 26 to cpu 26
ixg0: for TX/RX, interrupting at msix0 vec 27, bound queue 27 to cpu 27
ixg0: for TX/RX, interrupting at msix0 vec 28, bound queue 28 to cpu 28
ixg0: for TX/RX, interrupting at msix0 vec 29, bound queue 29 to cpu 29
ixg0: for TX/RX, interrupting at msix0 vec 30, bound queue 30 to cpu 30
ixg0: for TX/RX, interrupting at msix0 vec 31, bound queue 31 to cpu 31
ixg0: for link, interrupting at msix0 vec 32, affinity to cpu 0
ixg0: Using MSI-X interrupts with 33 vectors
ixg0: Ethernet address 0c:c4:7a:1f:82:dc
ixg0: PCI Express Bus: Speed 5.0GT/s Width x8
ixg0: feature cap 0x1780<LEGACY_TX,FDIR,MSI,MSIX,LEGACY_IRQ>
ixg0: feature ena 0x400<MSIX>
ixg1 at pci1 dev 0 function 1: Intel(R) PRO/10GbE PCI-Express Network Driver, Version - 4.0.1-k
ixg1: clearing prefetchable bit
ixg1: device 82599EB
ixg1: ETrackID 80000208
ixg1: for TX/RX, interrupting at msix1 vec 0, bound queue 0 to cpu 0
ixg1: for TX/RX, interrupting at msix1 vec 1, bound queue 1 to cpu 1
ixg1: for TX/RX, interrupting at msix1 vec 2, bound queue 2 to cpu 2
ixg1: for TX/RX, interrupting at msix1 vec 3, bound queue 3 to cpu 3
ixg1: for TX/RX, interrupting at msix1 vec 4, bound queue 4 to cpu 4
ixg1: for TX/RX, interrupting at msix1 vec 5, bound queue 5 to cpu 5
ixg1: for TX/RX, interrupting at msix1 vec 6, bound queue 6 to cpu 6
ixg1: for TX/RX, interrupting at msix1 vec 7, bound queue 7 to cpu 7
ixg1: for TX/RX, interrupting at msix1 vec 8, bound queue 8 to cpu 8
ixg1: for TX/RX, interrupting at msix1 vec 9, bound queue 9 to cpu 9
ixg1: for TX/RX, interrupting at msix1 vec 10, bound queue 10 to cpu 10
ixg1: for TX/RX, interrupting at msix1 vec 11, bound queue 11 to cpu 11
ixg1: for TX/RX, interrupting at msix1 vec 12, bound queue 12 to cpu 12
ixg1: for TX/RX, interrupting at msix1 vec 13, bound queue 13 to cpu 13
ixg1: for TX/RX, interrupting at msix1 vec 14, bound queue 14 to cpu 14
ixg1: for TX/RX, interrupting at msix1 vec 15, bound queue 15 to cpu 15
ixg1: for TX/RX, interrupting at msix1 vec 16, bound queue 16 to cpu 16
ixg1: for TX/RX, interrupting at msix1 vec 17, bound queue 17 to cpu 17
ixg1: for TX/RX, interrupting at msix1 vec 18, bound queue 18 to cpu 18
ixg1: for TX/RX, interrupting at msix1 vec 19, bound queue 19 to cpu 19
ixg1: for TX/RX, interrupting at msix1 vec 20, bound queue 20 to cpu 20
ixg1: for TX/RX, interrupting at msix1 vec 21, bound queue 21 to cpu 21
ixg1: for TX/RX, interrupting at msix1 vec 22, bound queue 22 to cpu 22
ixg1: for TX/RX, interrupting at msix1 vec 23, bound queue 23 to cpu 23
ixg1: for TX/RX, interrupting at msix1 vec 24, bound queue 24 to cpu 24
ixg1: for TX/RX, interrupting at msix1 vec 25, bound queue 25 to cpu 25
ixg1: for TX/RX, interrupting at msix1 vec 26, bound queue 26 to cpu 26
ixg1: for TX/RX, interrupting at msix1 vec 27, bound queue 27 to cpu 27
ixg1: for TX/RX, interrupting at msix1 vec 28, bound queue 28 to cpu 28
ixg1: for TX/RX, interrupting at msix1 vec 29, bound queue 29 to cpu 29
ixg1: for TX/RX, interrupting at msix1 vec 30, bound queue 30 to cpu 30
ixg1: for TX/RX, interrupting at msix1 vec 31, bound queue 31 to cpu 31
ixg1: for link, interrupting at msix1 vec 32, affinity to cpu 0
ixg1: Using MSI-X interrupts with 33 vectors
ixg1: Ethernet address 0c:c4:7a:1f:82:dd
ixg1: PCI Express Bus: Speed 5.0GT/s Width x8
ixg1: feature cap 0x1780<LEGACY_TX,FDIR,MSI,MSIX,LEGACY_IRQ>
ixg1: feature ena 0x400<MSIX>
ppb1 at pci0 dev 1 function 1: Intel E5 PCIe x8 or x4 (rev. 0x07)
ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci2 at ppb1 bus 19
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci0 dev 2 function 0: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb2: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x8 @ 8.0GT/s
ppb2: link is x4 @ 5.0GT/s
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci3 dev 0 function 0: Broadcom BCM5719 Gigabit Ethernet
bge0: APE firmware NCSI 1.0.88.0
bge0: interrupting at msix2 vec 0
bge0: HW config 002b11d4, 00006014, 0002aa08, 00000000 00000000
bge0: ASIC unknown BCM5719 (0x5719001), Ethernet address ac:16:2d:79:1c:d8
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5719C 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1 at pci3 dev 0 function 1: Broadcom BCM5719 Gigabit Ethernet
bge1: APE firmware NCSI 1.0.88.0
bge1: interrupting at msix3 vec 0
bge1: HW config 002b11d4, 00006014, 0002aa08, 00000000 00000000
bge1: ASIC unknown BCM5719 (0x5719001), Ethernet address ac:16:2d:79:1c:d9
bge1: setting short Tx thresholds
brgphy1 at bge1 phy 2: BCM5719C 1000BASE-T media interface, rev. 0
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge2 at pci3 dev 0 function 2: Broadcom BCM5719 Gigabit Ethernet
bge2: APE firmware NCSI 1.0.88.0
bge2: interrupting at msix4 vec 0
bge2: HW config 002b11d4, 00006014, 0002aa08, 00000000 00000000
bge2: ASIC unknown BCM5719 (0x5719001), Ethernet address ac:16:2d:79:1c:da
bge2: setting short Tx thresholds
brgphy2 at bge2 phy 3: BCM5719C 1000BASE-T media interface, rev. 0
brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge3 at pci3 dev 0 function 3: Broadcom BCM5719 Gigabit Ethernet
bge3: APE firmware NCSI 1.0.88.0
bge3: interrupting at msix5 vec 0
bge3: HW config 002b11d4, 00006014, 0002aa08, 00000000 00000000
bge3: ASIC unknown BCM5719 (0x5719001), Ethernet address ac:16:2d:79:1c:db
bge3: setting short Tx thresholds
brgphy3 at bge3 phy 4: BCM5719C 1000BASE-T media interface, rev. 0
brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ppb3 at pci0 dev 2 function 1: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb3: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci4 at ppb3 bus 20
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 2 function 2: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb4: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x8 @ 8.0GT/s
pci5 at ppb4 bus 2
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
ciss0 at pci5 dev 0 function 0: HP Smart Array 12
ciss0: interrupting at msix6 vec 0
ciss0: 2 LDs, HW rev 1, FW 7.02/7.02, 64bit fifo rro, method perf 0x20000005
scsibus0 at ciss0: 2 targets, 1 lun per target
ppb5 at pci0 dev 2 function 3: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb5: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci6 at ppb5 bus 21
pci6: i/o space, memory space enabled, rd/line, wr/inv ok
ppb6 at pci0 dev 3 function 0: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb6: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 8.0GT/s
pci7 at ppb6 bus 4
pci7: i/o space, memory space enabled, rd/line, wr/inv ok
ppb7 at pci0 dev 3 function 1: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb7: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci8 at ppb7 bus 22
pci8: i/o space, memory space enabled, rd/line, wr/inv ok
ppb8 at pci0 dev 3 function 2: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb8: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci9 at ppb8 bus 23
pci9: i/o space, memory space enabled, rd/line, wr/inv ok
ppb9 at pci0 dev 3 function 3: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb9: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci10 at ppb9 bus 24
pci10: i/o space, memory space enabled, rd/line, wr/inv ok
Intel E5 DMA (miscellaneous system, revision 0x07) at pci0 dev 4 function 0 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci0 dev 4 function 1 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci0 dev 4 function 2 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci0 dev 4 function 3 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci0 dev 4 function 4 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci0 dev 4 function 5 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci0 dev 4 function 6 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci0 dev 4 function 7 not configured
Intel E5 Address Map (miscellaneous system, revision 0x07) at pci0 dev 5 function 0 not configured
Intel E5 Error Reporting (miscellaneous system, revision 0x07) at pci0 dev 5 function 2 not configured
Intel E5 I/O APIC (interrupt system, IO(x) APIC, revision 0x07) at pci0 dev 5 function 4 not configured
ppb10 at pci0 dev 17 function 0: Intel C600 Virtual PCIe (rev. 0x05)
ppb10: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 2.5GT/s
pci11 at ppb10 bus 26
pci11: i/o space, memory space enabled, rd/line, wr/inv ok
ehci0 at pci0 dev 26 function 0: Intel C600 USB (rev. 0x05)
ehci0: interrupting at ioapic0 pin 21
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
usb0 at ehci0: USB revision 2.0
ppb11 at pci0 dev 28 function 0: Intel C600/X79 PCIe (rev. 0xb5)
ppb11: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 5.0GT/s
pci12 at ppb11 bus 10
pci12: i/o space, memory space enabled, rd/line, wr/inv ok
ppb12 at pci0 dev 28 function 7: Intel C600/X79 PCIe (rev. 0xb5)
ppb12: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
ppb12: link is x1 @ 2.5GT/s
pci13 at ppb12 bus 1
pci13: i/o space, memory space enabled, rd/line, wr/inv ok
Hewlett-Packard iLO3 Slave (miscellaneous system, revision 0x05) at pci13 dev 0 function 0 not configured
vga0 at pci13 dev 0 function 1: Matrox MGA G200eH (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1
wsmux1: connecting to wsdisplay0
pckbd_enable: command error
drm at vga0 not configured
Hewlett-Packard iLO3 Management (miscellaneous system, revision 0x05) at pci13 dev 0 function 2 not configured
uhci0 at pci13 dev 0 function 4: Hewlett-Packard iLO3 Virtual USB (rev. 0x02)
allocated pic msi7 type edge pin 0 level 6 to cpu1 slot 2 idt entry 98
uhci0: interrupting at msi7 vec 0
usb1 at uhci0: USB revision 1.0
ehci1 at pci0 dev 29 function 0: Intel C600 USB (rev. 0x05)
ehci1: interrupting at ioapic0 pin 20
ehci1: BIOS has given up ownership
ehci1: EHCI version 1.0
usb2 at ehci1: USB revision 2.0
ppb13 at pci0 dev 30 function 0: Intel 82801BA Hub-PCI Bridge (rev. 0xa5)
pci14 at ppb13 bus 25
pci14: i/o space, memory space enabled
ichlpcib0 at pci0 dev 31 function 0: Intel C600 LPC (rev. 0x05)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
tco0 at ichlpcib0: TCO (watchdog) timer configured.
tco0: autoconfiguration error: TCO timer reboot disabled by hardware; hope SMBIOS properly handles it.
tco0: Min/Max interval 1/367 seconds
pciide0 at pci0 dev 31 function 2: Intel C600/X79 SATA (rev. 0x05)
pciide0: bus-master DMA support present, but unused (no driver support)
pciide0: primary channel configured to native-PCI mode
pciide0: using ioapic0 pin 17 for native-PCI interrupt
atabus0 at pciide0 channel 0
pciide0: secondary channel configured to native-PCI mode
atabus1 at pciide0 channel 1
isa0 at ichlpcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, 1-byte FIFO
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 1-byte FIFO
pci15 at mainbus0 bus 32
pci15: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
ppb14 at pci15 dev 0 function 0: Intel E5 PCIe x4 (DMI2 Mode) (rev. 0x07)
ppb14: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 2.5GT/s
pci16 at ppb14 bus 49
pci16: i/o space, memory space enabled
ppb15 at pci15 dev 1 function 0: Intel E5 PCIe x8 or x4 (rev. 0x07)
ppb15: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci17 at ppb15 bus 42
pci17: i/o space, memory space enabled, rd/line, wr/inv ok
ppb16 at pci15 dev 1 function 1: Intel E5 PCIe x8 or x4 (rev. 0x07)
ppb16: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci18 at ppb16 bus 43
pci18: i/o space, memory space enabled, rd/line, wr/inv ok
ppb17 at pci15 dev 2 function 0: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb17: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x8 @ 8.0GT/s
pci19 at ppb17 bus 39
pci19: i/o space, memory space enabled, rd/line, wr/inv ok
ppb18 at pci15 dev 2 function 1: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb18: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci20 at ppb18 bus 44
pci20: i/o space, memory space enabled, rd/line, wr/inv ok
ppb19 at pci15 dev 2 function 2: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb19: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x8 @ 8.0GT/s
pci21 at ppb19 bus 36
pci21: i/o space, memory space enabled, rd/line, wr/inv ok
ppb20 at pci15 dev 2 function 3: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb20: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci22 at ppb20 bus 45
pci22: i/o space, memory space enabled, rd/line, wr/inv ok
ppb21 at pci15 dev 3 function 0: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb21: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 8.0GT/s
pci23 at ppb21 bus 33
pci23: i/o space, memory space enabled, rd/line, wr/inv ok
ppb22 at pci15 dev 3 function 1: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb22: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci24 at ppb22 bus 46
pci24: i/o space, memory space enabled, rd/line, wr/inv ok
ppb23 at pci15 dev 3 function 2: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb23: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci25 at ppb23 bus 47
pci25: i/o space, memory space enabled, rd/line, wr/inv ok
ppb24 at pci15 dev 3 function 3: Intel E5 PCIe x16, x8 or x4 (rev. 0x07)
ppb24: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 8.0GT/s
pci26 at ppb24 bus 48
pci26: i/o space, memory space enabled, rd/line, wr/inv ok
Intel E5 DMA (miscellaneous system, revision 0x07) at pci15 dev 4 function 0 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci15 dev 4 function 1 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci15 dev 4 function 2 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci15 dev 4 function 3 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci15 dev 4 function 4 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci15 dev 4 function 5 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci15 dev 4 function 6 not configured
Intel E5 DMA (miscellaneous system, revision 0x07) at pci15 dev 4 function 7 not configured
Intel E5 Address Map (miscellaneous system, revision 0x07) at pci15 dev 5 function 0 not configured
Intel E5 Error Reporting (miscellaneous system, revision 0x07) at pci15 dev 5 function 2 not configured
Intel E5 I/O APIC (interrupt system, IO(x) APIC, revision 0x07) at pci15 dev 5 function 4 not configured
acpicpu0 at cpu0: ACPI CPU
acpicpu0: C1: FFH, lat 1 us, pow 1000 mW
coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=90
acpicpu1 at cpu1: ACPI CPU
coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=90
acpicpu2 at cpu2: ACPI CPU
coretemp2 at cpu2: thermal sensor, 1 C resolution, Tjmax=90
acpicpu3 at cpu3: ACPI CPU
coretemp3 at cpu3: thermal sensor, 1 C resolution, Tjmax=90
acpicpu4 at cpu4: ACPI CPU
coretemp4 at cpu4: thermal sensor, 1 C resolution, Tjmax=90
acpicpu5 at cpu5: ACPI CPU
coretemp5 at cpu5: thermal sensor, 1 C resolution, Tjmax=90
acpicpu6 at cpu6: ACPI CPU
coretemp6 at cpu6: thermal sensor, 1 C resolution, Tjmax=90
acpicpu7 at cpu7: ACPI CPU
coretemp7 at cpu7: thermal sensor, 1 C resolution, Tjmax=90
acpicpu8 at cpu8: ACPI CPU
coretemp8 at cpu8: thermal sensor, 1 C resolution, Tjmax=90
acpicpu9 at cpu9: ACPI CPU
coretemp9 at cpu9: thermal sensor, 1 C resolution, Tjmax=90
acpicpu10 at cpu10: ACPI CPU
coretemp10 at cpu10: thermal sensor, 1 C resolution, Tjmax=90
acpicpu11 at cpu11: ACPI CPU
coretemp11 at cpu11: thermal sensor, 1 C resolution, Tjmax=90
acpicpu12 at cpu12: ACPI CPU
coretemp12 at cpu12: thermal sensor, 1 C resolution, Tjmax=90
acpicpu13 at cpu13: ACPI CPU
coretemp13 at cpu13: thermal sensor, 1 C resolution, Tjmax=90
acpicpu14 at cpu14: ACPI CPU
coretemp14 at cpu14: thermal sensor, 1 C resolution, Tjmax=90
acpicpu15 at cpu15: ACPI CPU
coretemp15 at cpu15: thermal sensor, 1 C resolution, Tjmax=90
acpicpu16 at cpu16: ACPI CPU
acpicpu17 at cpu17: ACPI CPU
acpicpu18 at cpu18: ACPI CPU
acpicpu19 at cpu19: ACPI CPU
acpicpu20 at cpu20: ACPI CPU
acpicpu21 at cpu21: ACPI CPU
acpicpu22 at cpu22: ACPI CPU
acpicpu23 at cpu23: ACPI CPU
acpicpu24 at cpu24: ACPI CPU
acpicpu25 at cpu25: ACPI CPU
acpicpu26 at cpu26: ACPI CPU
acpicpu27 at cpu27: ACPI CPU
acpicpu28 at cpu28: ACPI CPU
acpicpu29 at cpu29: ACPI CPU
acpicpu30 at cpu30: ACPI CPU
acpicpu31 at cpu31: ACPI CPU
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 1995000000 Hz quality 3000
scsibus0: waiting 2 seconds for devices to settle...
uhub0 at usb1: NetBSD (0x0000) UHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb2: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb0: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
IPsec: Initialized Security Association Processing.
aes: Intel AES-NI
chacha: x86 SSE2 ChaCha
adiantum: self-test passed
aes_ccm: self-test passed
blake2s: self-test passed
sd0 at scsibus0 target 0 lun 0: <HP, LOGICAL VOLUME, 7.02> disk fixed
sd0: 931 GB, 65535 cyl, 255 head, 116 sec, 512 bytes/sect x 1953459632 sectors
sd0: async, 8-bit transfers, tagged queueing
sd1 at scsibus0 target 1 lun 0: <HP, LOGICAL VOLUME, 7.02> disk fixed
sd1: 1862 GB, 65535 cyl, 255 head, 233 sec, 512 bytes/sect x 3906917808 sectors
sd1: async, 8-bit transfers, tagged queueing
uhub3 at uhub1 port 1: vendor 8087 (0x8087) product 0024 (0x0024), class 9/0, rev 2.00/0.00, addr 2
uhub3: single transaction translator
uhub3: 8 ports with 8 removable, self powered
uhub4 at uhub2 port 1: vendor 8087 (0x8087) product 0024 (0x0024), class 9/0, rev 2.00/0.00, addr 2
uhub4: single transaction translator
uhub4: 6 ports with 6 removable, self powered
uhub5 at uhub3 port 3: vendor 0424 (0x0424) product 2660 (0x2660), class 9/0, rev 2.00/8.01, addr 3
uhub5: single transaction translator
uhub5: 2 ports with 1 removable, self powered
uhidev0 at uhub4 port 3 configuration 1 interface 0
uhidev0: HEWLETT-PACKARD (0x03f0) Hewlett-Packard TFT7600 RKM (0x1f07), rev 1.10/1.04, addr 3, iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 3 configuration 1 interface 1
uhidev1: HEWLETT-PACKARD (0x03f0) Hewlett-Packard TFT7600 RKM (0x1f07), rev 1.10/1.04, addr 3, iclass 3/1
ums0 at uhidev1: 3 buttons and Z dir
wsmouse1 at ums0 mux 0
uhub5: detached
uhub5: at uhub3 port 3 (addr 3) disconnected
uhub5 at uhub3 port 3: vendor 0424 (0x0424) product 2660 (0x2660), class 9/0, rev 2.00/8.01, addr 3
uhub5: single transaction translator
uhub5: 2 ports with 1 removable, self powered
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <hp DVD A DS8A8SH, 627225049827, KHE4> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
cgd: self-test aes-xts-256
cgd: self-test aes-xts-512
cgd: self-test aes-cbc-128
cgd: self-test aes-cbc-256
cgd: self-test 3des-cbc-192
cgd: self-test blowfish-cbc-448
cgd: self-test aes-cbc-128 (encblkno8)
cgd: self-tests passed
WARNING: 1 error while detecting hardware; check system log.
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
kern.module.path=/stand/amd64/9.99.81/modules
ipmi0: version 32.0 interface KCS iobase 0xca2/0x2 spacing 1
ipmi0: ID 19.2 IPMI 2.0 Available
ipmi0: Additional Chassis FRU SEL SDR Sensor
ipmi0: Manufacturer 0000b Product 200b
ipmi0: Firmware 2.0
ciss0: normal state on 'ciss0:0' (online)
ciss0: normal state on 'ciss0:1' (online)
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
Home |
Main Index |
Thread Index |
Old Index